3D-Printed Fluidic Devices for Nanoparticle Preparation and Flow-Injection Amperometry Using Integrated Prussian Blue Nanoparticle-Modified Electrodes.

A consumer-grade fused filament fabrication (FFF) 3D printer was used to construct fluidic devices for nanoparticle preparation and electrochemical sensing. Devices were printed using poly(ethylene terephthalate) and featured threaded ports to connect polyetheretherketone (PEEK) tubing via printed fittings prepared from acrylonitrile butadiene styrene (ABS). These devices included channels designed to have 800 µm × 800 µm square cross sections and were semitransparent to allow visualization of the solution-filled channels. A 3D-printed device with a Y-shaped mixing channel was used to prepare Prussian blue nanoparticles (PBNPs) under flow rates of 100 to 2000 µL min(-1). PBNPs were then attached to gold electrodes for hydrogen peroxide sensing. 3D-printed devices used for electrochemical measurements featured threaded access ports into which a fitting equipped with reference, counter, and PBNP-modified working electrodes could be inserted. PBNP-modified electrodes enabled amperometric detection of H2O2 in the 3D-printed channel by flow-injection analysis, exhibiting a detection limit of 100 nM and linear response up to 20 µM. These experiments show that a consumer-grade FFF printer can be used to fabricate low-cost fluidic devices for applications similar to those that have been reported with more expensive 3D-printing methods.

Electrochemical study on the effects of epigenetic cytosine methylation on anti-benzo[a]pyrene diol epoxide damage at TP53 oligomers.

Anti-benzo[a]pyrene-r-7,t-8-dihydrodiol-t-9,10-epoxide (anti-BPDE) is a known carcinogen that damages DNA, and this damage is influenced by the DNA sequence and epigenetic factors. The influence of epigenetic cytosine methylation on the reaction with anti-BPDE at a known hotspot DNA damage site was studied electrochemically. Gold electrodes were modified with thiolated DNA oligomers spanning codons 270-276 of the TP53 gene. The oligomers exhibited 5-carbon cytosine methylation at the codon 273 location on the bound probe, the acquired complementary target, or both. Redox active diviologen compounds of the form C(12)H(25)V(2+)C(6)H(12)V(2+)C(12)H(25) (V(2+) = 4,4'-bipyridyl or viologen, C12-Viologen) were employed to detect anti-BPDE damage to DNA. DNA was exposed to racemic (±)- or enantiomerically pure (+)-anti-BPDE solutions followed by electrochemical interrogation in the presence of C12-Viologen. Background subtracted square wave voltammograms (SWV) showed the appearance of two peaks at approximately -0.38 V and -0.55 V vs Ag/AgCl upon anti-BPDE exposure. The acquired voltammetry is consistent with singly reduced C12-Viologen dimers bound at two different DNA environments, which arise from BPDE damage and are influenced by cytosine methylation and BPDE stereochemical considerations. UV spectroscopic and mass spectrometric methods employed to validate the electrochemical responses showed that (+)-anti-BPDE primarily adopts a minor groove bound orientation within the oligomers while selectively targeting the nontranscribed ssDNA sequence within the duplexes.

Electrochemical detection of anti-benzo[a]pyrene diol epoxide DNA damage on TP53 codon 273 oligomers.

DNA damage from (+/-)-anti-benzo[a]pyrene-7,8-dihydrodiol-9,10-epoxide (BPDE) at a hotspot TP53 gene sequence was electrochemically detected. BPDE was exposed to gold electrode immobilized double-stranded DNA oligomers followed by voltammetric measurements in the presence of redox-active C(12)H(25)V(2+)C(6)H(12)V(2+)C(12)H(25) (V(2+) = 4,4'-bipyridyl or viologen, C12-viologen). Square wave voltammograms from BPDE-exposed DNA-modified electrodes showed the emergence of a C12-viologen-DNA complex at -0.37 V versus Ag/AgCl. The peak current intensity of this redox wave was dependent on both BPDE concentration and exposure time. Controls with alternate xenobiotics and DNA sequences showed this redox wave to be primarily due to BPDE damage at the wild-type DNA sequence. The detection limit was determined to be approximately 170 nM BPDE. Mass spectrometry and UV thermal melting experiments provided insight into the BPDE reaction and mirrored the sensor results. This report demonstrates that an electrochemical hybridization sensor can be used to detect sequence-related xenobiotic DNA damage.