RESUMO
Antiviral and non-toxic effects of silver nanoparticles onto in vitro cells infected with coronavirus were evaluated in this study using High-Resolution Magic-Angle Spinning Nuclear Magnetic Resonance (HR-MAS NMR) spectroscopy. Silver nanoparticles were designed and synthesized using an orange flavonoid-hesperetin (HST)-for reduction of silver(I) and stabilization of as obtained nanoparticles. The bio-inspired process is a simple, clean, and sustainable way to synthesize biogenic silver nanoparticles (AgNP@HST) with diameters of â¼20 nm and low zeta potential (-40 mV), with great colloidal stability monitored for 2 years. The nanoparticles were used for the fabrication of two types of antiviral materials: colloids (AgNP@HST spray) and 3D flexible nanostructured composites. The composites, decorated with AgNP@HST (0.05 mmol L-1), were made using cellulose nanofibers (CNF) obtained from orange peel and graphene oxide (GO), being denominated CNF@GO@AgNP@HST. Both materials showed high virucidal activity against coronaviruses in cell infection in vitro models and successfully inhibited the viral activity in cells. HR-MAS 1H-NMR technique was used for determining nanomaterials' effects on living cells and their influences on metabolic pathways, as well as to study viral effects on cells. It was proven that none of the manufactured materials showed toxicity towards the intact cells used. Furthermore, viral infection was reverted when cells, infected with the coronavirus, were treated using the as-fabricated nanomaterials. These significant results open possibilities for antiviral application of 3D flexible nanostructured composite such as packaging papers and filters for facial masks, while the colloidal AgNP@HST spray can be used for disinfecting surfaces, as well as a nasal, mouth, and eye spray.
RESUMO
In this article we report a new laser processing method, combining the in situ graphitization of polyimide with simultaneous transfer of the graphene patterns to arbitrary substrates. The synthesis conditions are similar to those normally used for the well-known laser-induced graphene method. The approach is based on the enclosure of polyimide sheets between microscope glass slides. Graphene patterns have been successfully generated on glass and on PDMS, as well as graphene decorated with metals and oxides. In order to illustrate the usefulness of the proposed approach, the method was applied to the fabrication of hybrid supercapacitors, which exhibited very good electrochemical performance.
RESUMO
In this work we propose multilayer graphene (MLG) nanobelts for high current interconnections with single wall carbon nanotubes (SWCNT) and compare these with metal contacts. MLG contacts were directly printed on the SWCNT, without any additional metal parts, demonstrating the possibility to use these materials as interconnections in microelectronics. Different work function metals Al, Ti and Pd were probed for the lowest contact resistance with the SWCNT. Ti contacts demonstrated the best results among the metals owing to its work function being closest to the SWCNT and therefore giving the lowest Schottky barrier. Even though Ti contacts show the lowest contact resistance, the current density for MLG contacts was higher, giving the best results for high current interconnection applications. Moreover, MLG contacts show a stable and repeatable resistance decrease under high current conditions. Heat treatment of the MLG and metal contacts was completed in vacuum, in order to further reduce the contact resistance and optimal heat treatment conditions were found at 600 °C.
RESUMO
Palladium nanoparticles decorated reduced graphene oxide (Pd-rGO) and palladium nanoparticles intercalated inside nitrogen doped reduced graphene oxide (Pd-NrGO) hybrids have been synthesized by applying a very simple, fast and economic route using microwave-assisted in-situ reduction and exfoliation method. The Pd-NrGO hybrids materials show good activity as catalyst for ethanol electro oxidation for direct ethanol fuel cells (DEFCs) as compared to Pd-rGO hybrids. The enhanced direct ethanol fuel cell can serve as alternative to fossil fuels because it is renewable and environmentally-friendly with a high energy conversion efficiency and low pollutant emission. As proof of concept, the electrocatalytic activity of Pd-NrGO hybrid material was accessed by cyclic voltammetry in presence of ethanol to evaluate its applicability in direct-ethanol fuel cells (DEFCs). The Pd-NrGO catalyst presented higher electro active surface area (â¼6.3â¯m2â¯g-1) for ethanol electro-oxidation when compared to Pd-rGO hybrids (â¼3.7â¯m2â¯g-1). Despite the smaller catalytic activity of Pd-NrGO, which was attributed to the lower exfoliation rate of this material in relation to the Pd-rGO, Pd-NrGO showed to be very promising and its catalytic activity can be further improved by tuning the synthesis parameters to increase the exfoliation rate.
RESUMO
In this article we demonstrate a simple approach to fabricate interdigitated in-plane electrodes for flexible micro-supercapacitors (MSCs). A nanosecond ultraviolet laser treatment is used to reduce and pattern the electrodes on thick graphite oxide (GO) freestanding films. These laser-treated regions obtained by direct writing provide the conducting channels for electrons in the capacitors. The electrochemical performance of the MSCs was evaluated in the presence of two different electrolytes and they exhibit characteristics of nearly electrical double layer capacitors. The MSCs have areal capacitances as 2.40, 2.23 and 1.62µF/cm2 for NaOH, Na2SO4 and KCl electrolytes respectively, for measurements performed at the scan rate of 50mV/s. They retain â¼93.1% of their initial capacitances after 3500 cycles (scan rate=80mV/s) in NaOH electrolyte. The proposed laser treatment approach enables facile and fast fabrication of flexible MSCs without the need for tedious processing methods such as photolithographic micro-patterning and deposition of porous carbon or metallic current collectors.
RESUMO
In the present work, we have synthesized three-dimensional (3D) reduced graphene oxide nanosheets (rGO NSs) containing iron oxide nanoparticles (Fe3O4 NPs) hybrids (3D Fe3O4/rGO) by one-pot microwave approach. Structural and morphological studies reveal that the as-synthesized Fe3O4/rGO hybrids were composed of faceted Fe3O4 NPs induced into the interconnected network of rGO NSs. The morphologies and structures of the 3D hybrids have been characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectrometer (XPS). The electrochemical studies were analyzed by cyclic voltammetry, galvanostatic charge/discharge measurements, and electrochemical impedance spectroscopy, which demonstrate superior electrochemical performance as supercapacitors electrode application. The specific capacitances of 3D hybrid materials was 455 F g-1 at the scan rate of 8 mV s-1, which is superior to that of bare Fe3O4 NPs. Additionally, the 3D hybrid shows good cycling stability with a retention ratio of 91.4 after starting from â¼190 cycles up to 9600 cycles. These attractive results suggest that this 3D Fe3O4/rGO hybrid shows better performance as an electrode material for high-performance supercapacitors.