Magnesium Polymer Electrolytes Based on the Polycarbonate Poly(2-butyl-2-ethyltrimethylene-carbonate).

Magnesium electrolytes based on a polycarbonate with either magnesium tetrakis(hexafluoroisopropyloxy) borate (Mg(B(HFIP)4)2) or magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI)2) for magnesium batteries were prepared and characterized. The side-chain-containing polycarbonate, poly(2-butyl-2-ethyltrimethylene carbonate) (P(BEC)), was synthesized by ring opening polymerization (ROP) of 5-ethyl-5-butylpropane oxirane ether carbonate (BEC) and mixed with Mg(B(HFIP)4)2 or Mg(TFSI)2 to form low- and high-salt-concentration polymer electrolytes (PEs). The PEs were characterized by impedance spectroscopy, differential scanning calorimetry (DSC), rheology, linear sweep voltammetry, cyclic voltammetry, and Raman spectroscopy. A transition from classical salt-in-polymer electrolytes to polymer-in-salt electrolytes was indicated by a significant change in glass transition temperature as well as storage and loss moduli. Ionic conductivity measurements indicated the formation of polymer-in-salt electrolytes for the PEs with 40 mol % Mg(B(HFIP)4)2 (HFIP40). In contrast, the 40 mol % Mg(TFSI)2 PEs showed mainly the classical behavior. HFIP40 was further found to have an oxidative stability window greater than 6 V vs Mg/Mg2+, but showed no reversible stripping-plating behavior in an Mg||SS cell.

Closed Bipolar Electrode-Enabled Electrochromic Sensing of Multiple Metabolites in Whole Blood.

We report a closed bipolar electrode (CBE)-based sensing platform for the detection of diagnostic metabolites in undiluted whole human blood. The sensor is enabled by electrode chemistry based on: (1) a mixed layer of blood-compatible adsorption-resistant phosphorylcholine (PPC) and phenylbutyric acid (PBA), (2) ferrocene (Fc) redox mediators, and (3) immobilized redox-active enzymes. This scheme is designed to overcome nonspecific protein adsorption and amplify sensing currents in whole human fluids. The scheme also incorporates a diffusing mediator to increase electronic communication between the immobilized redox enzyme and the working electrode. The use of both bound and freely diffusing mediators is synergistic in producing the electrochemical response. The sensor is realized by linking the analyte cell, containing the specific electrode surface architecture, through a CBE to a reporter cell containing the electrochromic reporter, methyl viologen (MV). The colorless-to-purple color change accompanying the 1e- reduction of MV2+ is captured using a smartphone camera. Subsequent red-green-blue analysis is performed on the acquired images to determine cholesterol, glucose, and lactate concentrations in whole blood. The CBE blood metabolite sensor produces a linear color change at clinically relevant concentration ranges for all metabolites with good reproducibility (∼5% or better) and with limits of detection of 79 µM for cholesterol, 59 µM for glucose, and 86 µM for lactate. Finally, metabolite concentration measurements from the CBE blood metabolite sensor are compared with results from commercially available FDA-approved blood cholesterol, glucose, and lactate meters, with an average difference of ∼3.5% across all three metabolites in the ranges studied.

Chemistry-Performance Relationships of Polymer Gel-Electrolytes for Mg-S and Li-S Batteries: Influence of Network Cation Solvation Capacity on Polymer-Polysulfide Interactions.

Metal-sulfur batteries are a promising next-generation energy storage technology, offering high theoretical energy densities with low cost and good sustainability. An active area of research is the development of electrolytes that address unwanted migration of sulfur and intermediate species known as polysulfides during operation of metal-sulfur batteries, a phenomenon that leads to low energy efficiency and short life-spans. A particular class of electrolytes, gel polymer electrolytes, are especially attractive for their ability to repel polysulfides on the basis of structure, electrostatics, and other polymer properties. Herein, within the context of magnesium- and lithium-sulfur batteries, we investigate the impact of gel polymer electrolyte cation solvation capacity, a property related to network dielectric constant and chemistry, on sulfur/polysulfide-polymer interactions, an understudied property-performance relationship. Polymers with lower cation solvation capacity are found to permanently absorb less polysulfide active material, which increases sulfur utilization for Li-S batteries and significantly increases charge efficiency and life-span for Li-S and Mg-S batteries.

Electrochemical Immunosensing of Interleukin-6 in Human Cerebrospinal Fluid and Human Serum as an Early Biomarker for Traumatic Brain Injury.

In this work, we develop a label-free electrochemical immunosensor for the detection of interleukin-6 (IL-6) in human cerebrospinal fluid (CSF) and serum for diagnostic and therapeutic monitoring. The IL-6 immunosensor is fabricated from gold interdigitated electrode arrays (IDEAs) that are modified with IL-6 antibodies for direct antigen recognition and capture. A rigorous surface analysis of the sensor architecture was conducted to ensure high structural fidelity and performance. Electrochemical characterization was conducted by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), and sensing was performed using differential pulse voltammetry (DPV). The DPV peak current was used to quantify IL-6 in buffer, CSF, and serum in the range 1 pg mL-1 < [IL-6] < 1 µg mL-1. The IL-6 IDEA sensor achieved a limit of detection (LOD) of 1.63 pg mL-1 in PBS, 2.34 pg mL-1 in human CSF, and 11.83 pg mL-1 in human serum. The sensor response is linear in the concentration range 10 pg mL-1 < [IL-6] < 10 ng mL-1, and the sensor is selective for IL-6 over other common cytokines, including IL-10 and TNF-α. EIS measurements showed that the resistance to charge transfer, R CT, decreases upon IL-6 binding, an observation attributed to a structural change upon Ab-Ag binding that opens up the architecture so that the redox probe can more easily access the electrode surface. The IL-6 IDEA sensor can be used as a point-of-care diagnostic tool to deliver rapid results (∼3 min) in clinical settings for traumatic brain injury, and potentially address the unmet need for effective diagnostic and prognostic tools for other cytokine-related illnesses, such as sepsis and COVID-19 induced cytokine storms. Given the interdigitated electrode form factor, it is likely that the performance of the sensor can be further improved through redox cycling.

The Influence of Interfacial Chemistry on Magnesium Electrodeposition in Non-nucleophilic Electrolytes Using Sulfone-Ether Mixtures.

One of the limiting factors in the development of magnesium batteries is the reversibility of magnesium electrodeposition and dissolution at the anode. Often irreversibility is related to impurities and decomposition. Herein we report on the cycling behavior of magnesium metal anodes in different electrolytes, Mg(HMDS)2 - 4 MgCl2 in tetrahydrofuran (THF) and a butyl sulfone/THF mixture. The deposition morphology and anode-electrolyte interface is studied and related to Mg/Mg cell cycling performance. It is found that adding the sulfone caused the formation of a boundary layer at the electrode-electrolyte interface, which, in turn, resulted in a particle-like deposition morphology. This type of deposition has a high surface area, which alters the effective local current density and results in electronically isolated deposits. Extended cycling resulted in magnesium growth through a separator. Electrolyte decomposition is observed with and without the addition of the sulfone, however the addition of the sulfone increased the degree of decomposition.

Electrochemical Properties and Speciation in Mg(HMDS)2-Based Electrolytes for Magnesium Batteries as a Function of Ethereal Solvent Type and Temperature.

Magnesium batteries are a promising alternative to lithium-ion batteries due to the widespread abundance of magnesium and its high specific volumetric energy capacity. Ethereal solvents such as tetrahydrofuran (THF) are commonly used for magnesium-ion electrolytes due to their chemical compatibility with magnesium metal, but the volatile nature of THF is a concern for practical application. Herein, we investigate magnesium bis(hexamethyldisilazide) plus aluminum chloride (Mg(HMDS)2-AlCl3) electrolytes in THF, diglyme, and tetraglyme at varying temperature. We find that, despite the higher thermal stability of the glyme-based electrolytes, THF-based electrolytes have better reversibility at room temperature. Deposition/stripping efficiency is found to be a strong function of temperature. Diglyme-based Mg(HMDS)2-AlCl3 electrolytes are found to not exchange as quickly as THF and tetraglyme, stabilizing AlCl2+ and facilitating undesired aluminum deposition. Raman spectroscopy, 27Al NMR, and mass spectrometry are used to identify solution speciation.

Elemental Sulfur and Molybdenum Disulfide Composites for Li-S Batteries with Long Cycle Life and High-Rate Capability.

The practical implementation of Li-S technology has been hindered by short cycle life and poor rate capability owing to deleterious effects resulting from the varied solubilities of different Li polysulfide redox products. Here, we report the preparation and utilization of composites with a sulfur-rich matrix and molybdenum disulfide (MoS2) particulate inclusions as Li-S cathode materials with the capability to mitigate the dissolution of the Li polysulfide redox products via the MoS2 inclusions acting as "polysulfide anchors". In situ composite formation was completed via a facile, one-pot method with commercially available starting materials. The composites were afforded by first dispersing MoS2 directly in liquid elemental sulfur (S8) with sequential polymerization of the sulfur phase via thermal ring opening polymerization or copolymerization via inverse vulcanization. For the practical utility of this system to be highlighted, it was demonstrated that the composite formation methodology was amenable to larger scale processes with composites easily prepared in 100 g batches. Cathodes fabricated with the high sulfur content composites as the active material afforded Li-S cells that exhibited extended cycle lifetimes of up to 1000 cycles with low capacity decay (0.07% per cycle) and demonstrated exceptional rate capability with the delivery of reversible capacity up to 500 mAh/g at 5 C.

Comparison of Nanoscale Focused Ion Beam and Electrochemical Lithiation in ß-Sn Microspheres.

The development of Li focused ion beams (Li-FIB) enables controlled Li ion insertion into materials with nanoscale resolution. We take the first step toward establishing the relevance of the Li-FIB for studies of ion dynamics in electrochemically active materials by comparing FIB lithiation with conventional electrochemical lithiation of isolated ß-Sn microspheres. Samples are characterized by cross-sectioning with Ga FIB and imaging via electron microscopy. The Li-FIB and electrochemical lithiated Sn exhibit similarities that suggest that the Li-FIB can be a powerful tool for exploring dynamical Li ion-material interactions at the nanoscale in a range of battery materials.

Dynamics and Rheology of Soft Colloidal Glasses.

The linear viscoelastic (LVE) spectrum of a soft colloidal glass is accessed with the aid of a time-concentration superposition (TCS) principle, which unveils the glassy particle dynamics from in-cage rattling motion to out-of-cage relaxations over a broad frequency range 10-13 rad/s < ω < 101 rad/s. Progressive dilution of a suspension of hairy nanoparticles leading to increased intercenter distances is demonstrated to enable continuous mapping of the structural relaxation for colloidal glasses. In contrast to existing empirical approaches proposed to extend the rheological map of soft glassy materials, i.e., time-strain superposition (TSS) and strain-rate frequency superposition (SRFS), TCS yields a LVE master curve that satisfies the Kramers-Kronig relations which interrelate the dynamic moduli for materials at equilibrium. The soft glassy rheology (SGR) model and literature data further support the general validity of the TCS concept for soft glassy materials.

Suppression of lithium dendrite growth using cross-linked polyethylene/poly(ethylene oxide) electrolytes: a new approach for practical lithium-metal polymer batteries.

Solid polymer electrolyte (SPE) membranes are a critical component of high specific energy rechargeable Li-metal polymer (LMP) batteries. SPEs exhibit low volatility and thus increase the safety of Li-based batteries compared to current state-of-the-art Li-ion batteries that use flammable small-molecule electrolytes. However, most SPEs exhibit low ionic conductivity at room temperature, and often allow the growth of lithium dendrites that short-circuit the batteries. Both of these deficiencies are significant barriers to the commercialization of LMP batteries. Herein we report a cross-linked polyethylene/poly(ethylene oxide) SPE with both high ionic conductivity (>1.0 × 10(-4) S/cm at 25 °C) and excellent resistance to dendrite growth. It has been proposed that SPEs with shear moduli of the same order of magnitude as lithium could be used to suppress dendrite growth, leading to increased lifetime and safety for LMP batteries. In contrast to the theoretical predictions, the low-modulus (G' ≈ 1.0 × 10(5) Pa at 90 °C) cross-linked SPEs reported herein exhibit remarkable dendrite growth resistance. These results suggest that a high-modulus SPE is not a requirement for the control of dendrite proliferation.

25th anniversary article: polymer-particle composites: phase stability and applications in electrochemical energy storage.

Polymer-particle composites are used in virtually every field of technology. When the particles approach nanometer dimensions, large interfacial regions are created. In favorable situations, the spatial distribution of these interfaces can be controlled to create new hybrid materials with physical and transport properties inaccessible in their constituents or poorly prepared mixtures. This review surveys progress in the last decade in understanding phase behavior, structure, and properties of nanoparticle-polymer composites. The review takes a decidedly polymers perspective and explores how physical and chemical approaches may be employed to create hybrids with controlled distribution of particles. Applications are studied in two contexts of contemporary interest: battery electrolytes and electrodes. In the former, the role of dispersed and aggregated particles on ion-transport is considered. In the latter, the polymer is employed in such small quantities that it has been historically given titles such as binder and carbon precursor that underscore its perceived secondary role. Considering the myriad functions the binder plays in an electrode, it is surprising that highly filled composites have not received more attention. Opportunities in this and related areas are highlighted where recent advances in synthesis and polymer science are inspiring new approaches, and where newcomers to the field could make important contributions.