RESUMO
PURPOSE: To investigate the potential of two flow imaging microscopy (FIM) techniques (Micro-Flow Imaging (MFI) and FlowCAM) to determine total cell concentration and cell viability. METHODS: B-lineage acute lymphoblastic leukemia (B-ALL) cells of 2 different donors were exposed to ambient conditions. Samples were taken at different days and measured with MFI, FlowCAM, hemocytometry and automated cell counting. Dead and live cells from a fresh B-ALL cell suspension were fractionated by flow cytometry in order to derive software filters based on morphological parameters of separate cell populations with MFI and FlowCAM. The filter sets were used to assess cell viability in the measured samples. RESULTS: All techniques gave fairly similar cell concentration values over the whole incubation period. MFI showed to be superior with respect to precision, whereas FlowCAM provided particle images with a higher resolution. Moreover, both FIM methods were able to provide similar results for cell viability as the conventional methods (hemocytometry and automated cell counting). CONCLUSION: FIM-based methods may be advantageous over conventional cell methods for determining total cell concentration and cell viability, as FIM measures much larger sample volumes, does not require labeling, is less laborious and provides images of individual cells.
Assuntos
Contagem de Células/instrumentação , Sobrevivência Celular , Imagem Óptica/instrumentação , Linhagem Celular Tumoral , Citometria de Fluxo , Humanos , Microscopia/instrumentação , Leucemia-Linfoma Linfoblástico de Células Precursoras B/patologiaRESUMO
PURPOSE: To measure aggregate and particle formation in tumor necrosis factor-alpha (TNF-α) inhibitors etanercept, adalimumab and certolizumab pegol product samples after exposure to freezing temperature conditions similar to storage conditions previously observed in patients' homes. METHODS: TNF-α inhibitors in their original primary and secondary packaging were exposed to 32 freeze-thaw cycles (-10°C for 120min/5°C for 60 min) or continuous low storage temperature (-20°C for 96 h) before thawing at 2-8°C. Non-stressed products were used as controls. The products were analyzed by high pressure size exclusion chromatography (HP-SEC), dynamic light scattering (DLS), nanoparticle tracking analysis (NTA), micro-flow imaging (MFI) and second derivative ultraviolet (UV) spectroscopy. RESULTS: Ten out of twenty-one stressed product samples (47.6%) showed increased particle numbers in the submicron and micron size range when compared to controls. For each product, DLS, MFI and NTA detected an increase in particle level in at least one stressed syringe (both continuous freezing and freeze-thaw), whereas HP-SEC and UV spectroscopy showed no differences between stressed and non-stressed products. CONCLUSION: TNF-α inhibitors are relatively resistant to freezing temperatures similar to storage conditions previously observed in patients' homes. However, almost half of the stressed product samples showed formation of particles in the submicron and micron size range.
Assuntos
Anti-Inflamatórios/química , Fatores Biológicos/química , Congelamento/efeitos adversos , Agregados Proteicos , Fator de Necrose Tumoral alfa/antagonistas & inibidores , Adalimumab/química , Adalimumab/farmacologia , Anti-Inflamatórios/farmacologia , Fatores Biológicos/farmacologia , Certolizumab Pegol/química , Certolizumab Pegol/farmacologia , Química Farmacêutica , Armazenamento de Medicamentos/normas , Etanercepte/química , Etanercepte/farmacologia , Tamanho da PartículaRESUMO
PURPOSE: To investigate whether particle sedimentation velocity tracking using a flow imaging microscope (FlowCAM) can be used to determine microparticle porosity. METHODS: Two different methods were explored. In the first method the sedimentation rate of microparticles was tracked in suspending media with different densities. The porosity was calculated from the average apparent density of the particles derived by inter- or extrapolation to the density of a suspending medium in which the sedimentation velocity was zero. In the second method, the microparticle size and sedimentation velocity in one suspending fluid were used to calculate the density and porosity of individual particles by using the Stokes' law of sedimentation. RESULTS: Polystyrene beads of different sizes were used for the development, optimization and validation of the methods. For both methods we found porosity values that were in excellent agreement with the expected values. Both methods were applied to determine the porosity of three PLGA microparticle batches with different porosities (between about 4 and 52%). With both methods we obtained microparticle porosity values similar to those obtained by mercury intrusion porosimetry. CONCLUSIONS: We developed two methods to determine average microparticle density and porosity by sedimentation velocity tracking, using only a few milligrams of powder.