Theoretical Investigation of the Adsorbate and Potential-Induced Stability of Cu Facets During Electrochemical CO2 and CO Reduction.

The activity and product selectivity of electrocatalysts for reactions like the carbon dioxide reduction reaction (CO2RR) are intimately dependent on the catalyst's structure and composition. While engineering catalytic surfaces can improve performance, discovering the key sets of rational design principles remains challenging due to limitations in modeling catalyst stability under operating conditions. Herein, we perform first-principles density functional calculations adopting implicit solvation methods with potential control to study the influence of adsorbates and applied potential on the stability of different facets of model Cu electrocatalysts. Using coverage dependencies extracted from microkinetic models, we describe an approach for calculating potential and adsorbate-dependent contributions to surface energies under reaction conditions, where Wulff constructions are used to understand the morphological evolution of Cu electrocatalysts under CO2RR conditions. We identify that CO*, a key reaction intermediate, exhibits higher kinetically and thermodynamically accessible coverages on (100) relative to (111) facets, which can translate into an increased relative stabilization of the (100) facet during CO2RR. Our results support the known tendency for increased (111) faceting of Cu nanoparticles under more reducing conditions and that the relative increase in (100) faceting observed under CO2RR conditions is likely attributed to differences in CO* coverage between these facets.

Nanoscale Chemical and Structural Analysis during In Situ Scanning/Transmission Electron Microscopy in Liquids.

Liquid-cell scanning/transmission electron microscopy (S/TEM) has impacted our understanding of multiple areas of science, most notably nanostructure nucleation and growth and electrochemistry and corrosion. In the case of electrochemistry, the incorporation of electrodes requires the use of silicon nitride membranes to confine the liquid. The combined thickness of the liquid layer and the confining membranes prevents routine atomic-resolution characterization. Here, we show that by performing electrochemical water splitting in situ to generate a gas bubble, we can reduce the thickness of the liquid to a film approximately 30 nm thick that remains covering the sample. The reduced thickness of the liquid allows the acquisition of atomic-scale S/TEM images with chemical and valence analysis through electron energy loss spectroscopy (EELS) and structural analysis through selected area electron diffraction (SAED). This contrasts with a specimen cell entirely filled with liquid, where the broad plasmon peak from the liquid obscures the EELS signal from the sample and induces beam incoherence that impedes SAED analysis. The gas bubble generation is fully reversible, which allows alternating between a full cell and thin-film condition to obtain optimal experimental and analytical conditions, respectively. The methodology developed here can be applied to other scientific techniques, such as X-ray scattering, Raman spectroscopy, and X-ray photoelectron spectroscopy, allowing for a multi-modal, nanoscale understanding of solid-state samples in liquid media.

Surface Facet Engineering in Nanoporous Gold for Low-Loading Catalysts in Aluminum-Air Batteries.

The performance of metal-air batteries and fuel cells depends on the speed and efficiency of electrochemical oxygen reduction reactions at the cathode, which can be improved by engineering the atomic arrangement of cathode catalysts. It is, however, difficult to improve upon the performance of platinum nanoparticles in alkaline electrolytes with low-loading catalysts that can be manufactured at scale. Here, the authors synthesized nanoporous gold catalysts with increased (100) surface facets using electrochemical dealloying in sodium citrate surfactant electrolytes. These modified nanoporous gold catalysts achieved an 8% higher operating voltage and 30% greater power density in aluminum-air batteries over traditionally prepared nanoporous gold, and their performance was superior to commercial platinum nanoparticle electrodes at a 10 times lower mass loading. The authors used rotation disc electrode studies, backscattering of electrons, and underpotential deposition to show that the increased (100) facets improved the catalytic activity of citrate dealloyed nanoporous gold compared to conventional nanoporous gold. The citrate dealloyed samples also had the highest stability and least concentration of steps and kinks. The developed synthesis and characterization techniques will enable the design and synthesis of metal nanostructured catalysts with controlled facets for low-cost and mass production of metal-air battery cathodes.

Mechanism and Kinetics of Hydrogen Peroxide Decomposition on Platinum Nanocatalysts.

The decomposition of H2O2 to H2O and O2 catalyzed by platinum nanocatalysts controls the energy yield of several energy conversion technologies, such as hydrogen fuel cells. However, the reaction mechanism and rate-limiting step of this reaction have been unsolved for more than 100 years. We determined both the reaction mechanism and rate-limiting step by studying the effect of different reaction conditions, nanoparticle size, and surface composition on the rates of H2O2 decomposition by three platinum nanocatalysts with average particle sizes of 3, 11, and 22 nm. Rate models indicate that the reaction pathway of H2O2 decomposition is similar for all three nanocatalysts. Larger particle size correlates with lower activation energy and enhanced catalytic activity, explained by a smaller work function for larger platinum particles, which favors chemisorption of oxygen onto platinum to form Pt(O). Our experiments also showed that incorporation of oxygen at the nanocatalyst surface results in a faster reaction rate because the rate-limiting step is skipped in the first cycle of reaction. Taken together, these results indicate that the reaction proceeds in two cyclic steps and that step 1 is the rate-limiting step. Step 1: Pt + H2 O2 → H2 O + Pt( O). Step 2: Pt( O) + H2 O2 → Pt + O2 + H2 O. Overall: 2 H2 O2 → O2 + 2 H2 O. Establishing relationships between the properties of commercial nanocatalysts and their catalytic activity, as we have done here for platinum in the decomposition of H2O2, opens the possibility of improving the performance of nanocatalysts used in applications. This study also demonstrates the advantage of combining detailed characterization and systematic reactivity experiments to understand property-behavior relationships.

Production of water-soluble few-layer graphene mesosheets by dry milling with hydrophobic drug.

A novel, fast, and easy mechano-chemistry-based (dry milling) method has been developed to exfoliate graphene with hydrophobic drugs generating few-layer graphene mesosheets (< 10 nm in thickness and ∼1 µm in width). The electronic properties of the graphitic structure were partially preserved after the milling treatment compared with graphene oxide prepared by Hummers' method. Several characterization techniques such as thermogravimetric analysis, Raman spectroscopy, atomic force microscopy, electron microscopy, and molecular dynamics simulation were used to characterize this material. The drug-exfoliated mesosheets were pharmacologically inactive, offering a new approach for making water-soluble few-layer graphene mesosheets upon dry milling with hydrophobic drugs, mainly used as exfoliating agents.