Flexibility of Room-Temperature-Synthesized Amorphous CdO-In2O3 Alloy Films and Their Application as Transparent Conductors in Solar Cells.

Due to their low-temperature deposition, high mobility (>10 cm2/V·s), and electrical conductivity, amorphous ionic oxide semiconductors (AIOSs) have received much attention for their applications in flexible and/or organic electro-optical devices. Here, we report on a study of the flexibility of CdO-In2O3 alloy thin films, deposited on a polyethylene terephthalate (PET) substrate by radio frequency magnetron sputtering at room temperature. Cd1-xInxO1+δ alloys with the composition of x > 0.6 are amorphous, exhibiting a high electron mobility of 40-50 cm2/V·s, a low resistivity of ∼3 × 10-4 Ω·cm, and high transmittance over a wide spectral window of 350 to >1600 nm. The flexibility of both crystalline and amorphous Cd1-xInxO1+δ films on the PET substrate was investigated by measuring their electrical resistivity after both compressive and tensile bending with a range of bending radii and repeated bending cycles. Under both compressive and tensile bending with Rb = 16.5 mm, no significant degradation was observed for both the crystalline and amorphous films up to 300 bending cycles. For a smaller bending radius, the amorphous film shows much less electrical degradation than the crystalline films under compressive bending due to less film delamination at the bending sites. On the other hand, for a small bending radius (<16 mm), both crystalline and amorphous films degrade after repeated tensile bending, most likely due to the development of microcracks in the films. To demonstrate the application of amorphous Cd1-xInxO1+δ alloy in photovoltaics, we fabricated perovskite and bulk-heterojunction organic solar cells (OSCs) on glass and flexible PET utilizing amorphous Cd1-xInxO1+δ layers as transparent electrodes. The organic-inorganic hybrid perovskite solar cells (PSCs) exhibit a power conversion efficiency (PCE) of ∼11 to 12% under both front and back illumination, demonstrating good bifacial performance with bifaciality factor >90%. The OSCs fabricated on an amorphous Cd1-xInxO1+δ-coated flexible PET substrate achieve a promising PCE of 12.06%. Our results strongly suggest the technological potentials of amorphous Cd1-xInxO1+δ as a reliable and effective transparent conducting material for flexible and organic optoelectronic devices.

Two-Step Chemical Vapor Deposition-Synthesized Lead-Free All-Inorganic Cs3Sb2Br9 Perovskite Microplates for Optoelectronic Applications.

Lead-based halide perovskites (APbX3, where A = organic or inorganic cation, X = Cl, Br, I) are suitable materials for many optoelectronic devices due to their many attractive properties. However, the concern of lead toxicity and the poor ambient and operational stability of the organic cation group greatly limit their practical utilization. Therefore, there has recently been great interest in lead-free, environment-friendly all-inorganic halide perovskites (IHPs). Sb and Sn are common species suggested to replace Pb for Pb-free IHPs. However, the large difference in the melting points of the precursor materials (e.g., CsBr and SbBr3 precursors for Cs3Sb2Br9) makes the chemical vapor deposition (CVD) growth of high-quality Pb-free IHPs a very challenging task. In this work, we developed a two-step CVD method to overcome this challenge and successfully synthesized Pb-free Cs3Sb2Br9 perovskite microplates. Cs3Sb2Br9 microplates ∼25 µm in size with the exciton absorption peak at ∼2.8 eV and a band gap of ∼2.85 eV were obtained. The microplates have a smooth hexagonal morphology and show a large Stokes shift of ∼450 meV and exciton binding energy of ∼200 meV. To demonstrate the applications of these microplates in optoelectronics, simple photoconductive devices were fabricated. These photodetectors exhibit a current on/off ratio of 2.36 × 102, a responsivity of 36.9 mA/W, and a detectivity of 1.0 × 1010 Jones with a fast response of rise and decay time of 61.5 and 24 ms, respectively, upon 450 nm photon irradiation. Finally, the Cs3Sb2Br9 microplates also show good stability in ambient air without encapsulation. These results demonstrate that the 2-step CVD process is an effective approach to synthesize high-quality all-inorganic lead-free Cs3Sb2Br9 perovskite microplates that have the potential for future high-performance optoelectronic device applications.