One-step electrodeposited hybrid nanofilms in amperometric biosensor development.

This review summarizes recent developments in amperometric biosensors, based on one-step electrodeposited organic-inorganic hybrid layers, used for analysis of low molecular weight compounds. The factors affecting self-assembly of one-step electrodeposited films, methods for verifying their composition, advantages, limitations and approaches affecting the electroanalytical performance of amperometric biosensors based on organic-inorganic hybrid layers were systemized. Moreover, issues related to the formation of one-step organic-inorganic hybrid functional layers with different structures in biosensors produced under the same electrodeposition parameters are discussed. The systemized dependencies can support the preliminary choice of functional sensing layers with architectures tuned for specific biotechnology and life science applications. Finally, the capabilities of one-step electrodeposition of organic-inorganic hybrid functional films beyond amperometric biosensors were highlighted.

A novel copper (II) binding peptide for a colorimetric biosensor system design.

Filamentous bacteriophages are viruses infecting only bacteria. In this study, phage display technique was applied to identify highly selective Cu(II) binding peptides. After five rounds of positive screening against Cu(II) and various rounds of negative screenings against competitive metal ions (Al(III), Co(II), Fe(III), Ni(II) and Zn(II)), bacteriophages were enriched. Selective Cu(II) binding of final phages was confirmed by Enzyme Linked Immunosorbent Assay (ELISA), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray spectroscopy (EDX) analyses. 15 phage plaques were randomly selected and sequenced. Cu-5 peptide (HGFANVA) with the highest frequency of occurrence and the strongest Cu(II) affinity was chosen for further Cu(II) detection and removal tests. Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) confirmed the strong Cu(II) binding potential of engineered viruses. Cu-5 peptides were synthetically synthesized with three Cysteine units at C-terminal and a AuNP-peptide biosensor system was developed based on aggregation behavior of AuNPs upon Cu(II) ion treatment. AuNP-based Cu(II) sensor was selective for Cu(II) and the LOD was 91.15 nM (ca. 5.8 × 10-3 mg/L; 3σ/k, n = 5, R2 = 0.992) for the case study which is considerably lower than the WHO's accepted guideline of 1.3 mg/L. This study provides an interdisciplinary approach to apply short peptides as recognition units for biosensor studies which are user friendly, not bulky and cost-effective.

Toward Alginate-Based Membrane Technology for High Performance Recovery of Heavy Metals in Cells.

One of the major environmental problems is a global metal contamination. Heavy metals are nonbiodegradable and tend to accumulate in living organisms. Therefore, searching for biocompatible materials with enhanced sorption capabilities for selective removal of toxic elements from complex environments, low cost, ease of operation, and large available quantities that meet all requirements of the Green Chemistry concept is a current engineering and analytical task. We present a comprehensive study toward construction of an advanced biomembrane-based technology for recovery of several heavy metals and ruthenium by microdimensional alginate scaffolds. The chosen design of alginate scaffolds and their operational conditions were monitored during removal of Cd(II), Co(II), Pb(II), As(III), and Ru(III) in modeled aqueous solutions, cell culture medium, and in the presence of A549 lung cells by a tandem of biological (live/dead cell test), physical nanoanalytical (TEM/EDX, SEM/EDX), and chemical (FT-IR, HR-ICP-MS) assays. More precisely, the impact of certain experimental conditions, viz., medium acidity and matrix effects on sorption capacity of the above-mentioned elements, was investigated in detail. Remarkably, a different attachment behavior during adsorption of chosen elements by alginate scaffolds was observed. In addition, we revealed an essential concentration dependent effect of loaded heavy metals and ruthenium on cultivated cells. The obtained data allow us to gain a deeper insight into the interactions occurring in the studied biomaterial-inorganic system. Moreover, the obtained dependencies can be widely used for the development of alginate-based membrane technology employed for the protection of environmental and biological samples from the toxic pollutants.

Automated Electrochemical Glucose Biosensor Platform as an Efficient Tool Toward On-Line Fermentation Monitoring: Novel Application Approaches and Insights.

Monitoring and control of fermentation processes remain a crucial challenge for both laboratory and industrial-scale experiments. Reliable identification and quantification of the key process parameters in on-line mode allow operation of the fermentation at optimal reactor efficiency, maximizing productivity while minimizing waste. However, state-of-the-art fermentation on-line monitoring is still limited to a number of standard measurements such as pH, temperature and dissolved oxygen, as well as off-gas analysis as an advanced possibility. Despite the availability of commercial biosensor-based platforms that have been established for continuous monitoring of glucose and various biological variables within healthcare, on-line glucose quantification in fermentation processes has not been implemented yet to a large degree. For the first time, this work presents a complete study of a commercial flow-through-cell with integrated electrochemical glucose biosensors (1st generation) applied in different media, and importantly, at- and on-line during a yeast fed-batch fermentation process. Remarkably, the glucose biosensor-based platform combined with the developed methodology was able to detect glucose concentrations up to 150 mM in the complex fermentation broth, on both cell-free and cell-containing samples, when not compromised by oxygen limitations. This is four to six-fold higher than previously described in the literature presenting the application of biosensors predominately toward cell-free fermentation samples. The automated biosensor platform allowed reliable glucose quantification in a significantly less resource and time (<5 min) consuming manner compared to conventional HPLC analysis with a refractive index (RI) detector performed as reference measurement. Moreover, the presented biosensor platform demonstrated outstanding mechanical stability in direct contact with the fermentation medium and accurate glucose quantification in the presence of various electroactive species. Coupled with the developed methodology it can be readily considered as a simple, robust, accurate and inexpensive tool for real-time glucose monitoring in fermentation processes.

The Role of Nanoanalytics in the Development of Organic-Inorganic Nanohybrids-Seeing Nanomaterials as They Are.

The functional properties of organic-inorganic (O-I) hybrids can be easily tuned by combining system components and parameters, making this class of novel nanomaterials a crucial element in various application fields. Unfortunately, the manufacturing of organic-inorganic nanohybrids still suffers from mechanical instability and insufficient synthesis reproducibility. The control of the composition and structure of nanosurfaces themselves is a specific analytical challenge and plays an important role in the future reproducibility of hybrid nanomaterials surface properties and response. Therefore, appropriate and sufficient analytical methodologies and technical guidance for control of their synthesis, characterization and standardization of the final product quality at the nanoscale level should be established. In this review, we summarize and compare the analytical merit of the modern analytical methods, viz. Fourier transform infrared spectroscopy (FTIR), RAMAN spectroscopy, surface plasmon resonance (SPR) and several mass spectrometry (MS)-based techniques, that is, inductively coupled plasma mass spectrometry (ICP-MS), single particle ICP-MS (sp-ICP-MS), laser ablation coupled ICP-MS (LA-ICP-MS), time-of-flight secondary ion mass spectrometry (TOF-SIMS), liquid chromatography mass spectrometry (LC-MS) utilized for characterization of O-I nanohybrids. Special attention is given to laser desorption ionization mass spectrometry (LDI-MS) as a reliable nanoanalytical platform for characterization of O-I hybrid nanomaterials, their quality, design verification and validation.

Sensors for biosensors: a novel tandem monitoring in a droplet towards efficient screening of robust design and optimal operating conditions.

Understanding the biorecognition and transduction mechanisms is a key aspect in the development of robust sensing technologies. Therefore, the design of tools and analytical approaches that could allow gaining a deeper insight into the bio- and electrochemical processes would significantly accelerate the progress in the field of biosensors. Herein, we present a novel effective strategy for biosensor design screening based on tandem monitoring of individual system parameters in a droplet. The developed tandem approach couples the simultaneous chronoamperometric characterization of biosensors in the presence of an analyte (glucose) together with dissolved oxygen monitoring using a luminescence-based optical oxygen microsensor. Remarkably, an optical sensor was applied for the first time to analyse the amperometric biosensor response and kinetics. Two types of multi-layer glucose biosensors (first generation) were chosen as a case study and were evaluated at various operating conditions using multi-analytical techniques. Moreover, specific protocols were developed for the detection of oxygen conversion rates, iron and membrane elution inside the multi-layer glucose biosensor system. The presented tandem monitoring approach allows one to identify and build-up the correlations between the critical operation conditions and system parameters affecting the overall biosensor response, its sensitivity and lifetime. Thus, based on the obtained experimental results a more favorable composition of Nafion membrane films and enzyme loadings for glucose biosensors were identified in a time-efficient way and allowed to explain an improved stability (up to 3 months) and linear detection range of glucose concentrations (up to 5 mM). Furthermore, the presented tandem monitoring approach can be readily adapted to other oxygen dependent types of biosensors either for simultaneous multiple substrate detection or as an efficient tool for biosensor design and operating condition screening.

A study of enhanced ion formation from metal-semiconductor complexes in atmospheric pressure laser desorption/ionization mass spectrometry.

The study of the key parameters impacted surface-assisted laser desorption/ionization-mass spectrometry is of broad interest. In previous studies, it has been shown that surface-assisted laser desorption/ionization-mass spectrometry is a complex process depending on multiple factors. In the presented study, we showed that neither porosity, light absorbance nor surface hydrophobicity alone influence the enhancement phenomena observed from the hybrid metal-semiconductor complexes versus individual targets, but small changes in the analyte attaching to the target significantly affect laser desorption ionization-efficiency. By means of Raman spectroscopy and scanning electron microscopy, it was revealed that the formation of an amorphous analyte layer after drying on a solid substrate was essential for the enhanced laser desorption ionization-signal observed from the hybrid metal-semiconductor targets, and the crystallization properties of the analyte appeared as a function of the substrate. Obtained results were used for the screening of regular and lactose-free milk samples through the hybrid metal-semiconductor target. Copyright © 2016 John Wiley & Sons, Ltd.

Interactions between DPPC as a component of lung surfactant and amorphous silica nanoparticles investigated by HILIC-ESI-MS.

This paper reports a rapid HILIC-ESI-MS assay to quantify dipalmitoylphosphatidylcholine (DPPC) as component of lung surfactant for nanosafety studies. The technique was used to investigate the concentration-dependent sorption of DPPC to two-sizes of amorphous SiO2 nanoparticles (SiO2-NPs) in a MeOH:H2O (50/50v/v) mixture and in cell culture medium. In MeOH:H2O (50/50v/v), the sorption of DPPC was positively correlated with the nanoparticles concentration. A substantial affinity of small amorphous SiO2-NPs (25nm) to DPPC standard solution compared to bigger SiO2-NPs (75nm) was not confirmed for biological specimens. After dispersion of SiO2-NPs in DPPC containing cell culture medium, the capacity of the SiO2-NPs to bind DPPC was reduced in comparison to a mixture of MeOH:H2O (50/50v/v) regardless from the nanoparticles size. Furthermore, HILIC-ESI-MS revealed that A549 cells internalized DPPC during growth in serum containing medium complemented with DPPC. This finding was in a good agreement with the potential of alveolar type II cells to recycle surfactant components. Binding of lipids present in the cell culture medium to amorphous SiO2-NPs was supported by means of HILIC-ESI-MS, TEM and ICP-MS independently.

p-Coumaric acid, a novel and effective biomarker for quantifying hypoxic stress by HILIC-ESI-MS.

In this study, we report p-coumaric acid as novel and effective response marker for indirectly measuring the levels of hypoxia in normal primary bronchial epithelial cells. We developed a simple and rapid technique based on hydrophilic interaction chromatography-electrospray ionization-mass spectrometry (HILIC-ESI-MS). During 168h of hypoxia without induction of reactive oxygen species (ROS), an almost linear increase of p-coumaric acid levels was observed. We interpret the increasing p-coumaric acid concentrations during hypoxia as a result of cell damage, triggered by reduced co-enzyme Q10 levels, because the oxidative cascade was not able to supply sufficient energy. The HILIC-ESI-MS assay within p-coumaric acid exhibited a linear dynamic range from 60 to 610 ng/µL with correlation coefficient of 0.9998. The precision of the assay was ≤15% RSD and method accuracies between 97 and 108%.

Influence of surface melting effects and availability of reagent ions on LDI-MS efficiency after UV laser irradiation of Pd nanostructures.

In this study, the influence of surface morphology, reagent ions and surface restructuring effects on atmospheric pressure laser desorption/ionization (LDI) for small molecules after laser irradiation of palladium self-assembled nanoparticular (Pd-NP) structures has been systematically studied. The dominant role of surface morphology during the LDI process, which was previously shown for silicon-based substrates, has not been investigated for metal-based substrates before. In our experiments, we demonstrated that both the presence of reagent ions and surface reorganization effects--in particular, melting--during laser irradiation was required for LDI activity of the substrate. The synthesized Pd nanostructures with diameters ranging from 60 to 180 nm started to melt at similar temperatures, viz. 890-898 K. These materials exhibited different LDI efficiencies, however, with Pd-NP materials being the most effective surface in our experiments. Pd nanostructures of diameters >400-800 nm started to melt at higher temperatures, >1000 K, making such targets more resistant to laser irradiation, with subsequent loss of LDI activity. Our data demonstrated that both melting of the surface structures and the presence of reagent ions were essential for efficient LDI of the investigated low molecular weight compounds. This dependence of LDI on melting points was exploited further to improve the performance of Pd-NP-based sampling targets. For example, adding sodium hypophosphite as reducing agent to Pd electrolyte solutions during synthesis lowered the melting points of the Pd-NP materials and subsequently gave reduced laser fluence requirements for LDI.

Sorption of hydrophilic dyes on anodic aluminium oxide films and application to pH sensing.

The sorption of selected hydrophilic pH-sensitive dyes (bromophenol blue, bromothymol blue, bromocresol purple, alizarin red, methyl orange, congo red, rhodamine 6G) on films of anodized aluminium oxide (AAO) was investigated in this study. Depth and pore structure of the AAO channels were adjusted by changing electrolysis time and current density during treatment of aluminium foil in oxalic acid, sulfosalycilic acid and sulfuric acid at concentration levels between 0.2 and 0.6 M. The dyes were immobilized on the AAO surface by direct saturation of the films in dye solutions. It was shown by scanning electron microscopy and X-ray spectral analysis that the dyes penetrated into the AAO channels by more than 1.5 µm, even at static saturation conditions. The anionic dyes linked to the porous AAO surface exhibited differential shifts of the UV absorption bands in their acidic/basic forms. By combining several dyes, the films have an application range between pH = 0.5-9 in aqueous media. The dye-modified AAO film was a simple, portable, inexpensive and reusable pH sensor with very fast response time and clear colour transitions.

The role of physical and chemical properties of Pd nanostructured materials immobilized on inorganic carriers on ion formation in atmospheric pressure laser desorption/ionization mass spectrometry.

Fundamental parameters influencing the ion-producing efficiency of palladium nanostructures (nanoparticles [Pd-NP], nanoflowers, nanofilms) during laser irradiation were studied in this paper. The nanostructures were immobilized on the surface of different solid inorganic carrier materials (porous and mono-crystalline silicon, anodic porous aluminum oxide, glass and polished steel) by using classical galvanic deposition, electroless local deposition and sputtering. It was the goal of this study to investigate the influence of both the nanoparticular layer as well as the carrier material on ion production for selected analyte molecules. Our experiments demonstrated that the dimensions of the synthesized nanostructures, the thickness of the active layers, surface disorders, thermal conductivity and physically or chemically adsorbed water influenced signal intensities of analyte ions during surface-assisted laser desorption/ionization (SALDI) while no effects such as plasmon resonance, photoelectric effect or catalytic activity were expected to occur. Excellent LDI abilities were seen for Pd-NPs immobilized on steel, while Pd nanoflowers on porous silicon exhibited several disadvantages; viz, strong memory effects, dependency of the analytical signal on amount of physically and chemically adsorbed water inside porous carrier, reduced SALDI activity from unstable connections between Pd and semiconductor material, decrease of the melting point of pure silicon after Pd immobilization and resulting strong laser ablation of metal/semiconductor complex, as well as significantly changed surface morphology after laser irradiation. The analytical performance of Pd-NP/steel was further improved by applying a hydrophobic coating to the steel surface before galvanic deposition. This procedure increased the distance between Pd-NPs, thus reducing thermal stress upon LDI; it simultaneously decreased spot sizes of deposited sample solutions.

Novel galvanic nanostructures of Ag and Pd for efficient laser desorption/ionization of low molecular weight compounds.

A simple approach for synthesis of palladium and silver nanostructures with readily adjustable morphologies was developed using galvanic electrochemical deposition, for application to surface-assisted laser desorption/ionization (SALDI) of small biological molecules. A range of fatty acids, triglycerides, carbohydrates, and antibiotics were investigated to assess the performance of the new materials. Intense analyte cations were generated from the galvanic surfaces upon UV laser irradiation such as potassium adducts for a film thickness <100 nm (originating from impurities of the electrolyte solution) and Pd and Ag cluster ions for films with a thickness >120 nm. Possible laser desorption/ionization mechanisms of these galvanic structures are discussed. The films exhibited self-organizing abilities and adjustable morphologies by changing electrochemical parameters. They did not require any stabilizing agents and were inexpensive and very easy to produce. SALDI analysis showed that the materials were stable under ambient conditions and analytical results with excellent measurement reproducibility and detection sensitivity similar to MALDI were obtained. Finally, we applied the galvanic surfaces to fast screening of natural oils with minimum sample preparation.

Nanostructured solid substrates for efficient laser desorption/ionization mass spectrometry (LDI-MS) of low molecular weight compounds.

Analytical applications often require rapid measurement of compounds from complex sample mixtures. High-speed mass spectrometry approaches frequently utilize techniques based on direct ionization of the sample by laser irradiation, mostly by means of matrix-assisted laser desorption/ionization (MALDI). Compounds of low molecular weight are difficult to analyze by MALDI, however, because of severe interferences in the low m/z range from the organic matrix used for desorption/ionization. In recent years, surface-assisted laser desorption/ionization (SALDI) techniques have shown promise for small molecule analysis, due to the unique properties of nanostructured surfaces, in particular, the lack of a chemical background in the low m/z range and enhanced production of analyte ions by SALDI. This short review article presents a summary of the most promising recent developments in SALDI materials for MS analysis of low molecular weight analytes, with emphasis on nanostructured materials based on metals and semiconductors.