Mechanics of a Biomimetic Moisture Sensitive Actuator Based on Compression Wood.

Various mechanisms of plant organ movements have been reported, including the close association of two layers with expressed differences in hygroscopic properties. Following this principle, actuator beams composed of thin veneers out of normal and compression wood cut from Scots pine (Pinus sylvestris L.) were prepared by using two types of adhesives. The mismatch of the swelling properties of the two layers in tight combination resulted in an expressed bending deflection in response to set humidity changes. The resulting curvatures were measured and analyzed by the Timoshenko bi-metal-model, as well as with an enhanced three-layer model, with the latter also considering the mechanical influence of the glueline on the actuator bending. The thermally induced strain in the original model was replaced by another strain due to moisture changes. The strain was modelled as a function of wood density, along with changes in wood moisture. Experiments with free movement of the bilayer to measure curvature, and with constraints to determine forces, were performed as well. Deformation and magnitude of actuators movements were in close agreement with the enhanced bilayer-model for the phenol-resorcinol-formaldehyde adhesive, which deviated substantially from the casein adhesive glued actuators. The obtained results are seen as critical for wood-based actuator systems that are potentially used in buildings or other applications.

Biofilm-Forming Ability of Microbacterium lacticum and Staphylococcus capitis Considering Physicochemical and Topographical Surface Properties.

Biofilm characteristics of Microbacterium lacticum D84 (M. lacticum) and Staphylococcus capitis subsp. capitis (S. capitis) on polytetrafluoroethylene and AISI-304 stainless steel at early- (24, 48 h) and late-stage (144, 192 h) biofilm formation were investigated. M. lacticum biofilm structure was more developed compared to S. capitis, representing vastly mature biofilms with a strongly developed amorphous matrix, possibly extracellular polymeric substances (EPSs), at late-stage biofilm formation. S. capitis showed faster growth behavior but still resulted in a relatively flat biofilm structure. Strong correlations were found between several roughness parameters and S. capitis surface coverage (r ≥ 0.98), and between total surface free energy (γs) and S. capitis surface coverage (r = 0.89), while M. lacticum remained mostly unaffected. The pronounced ubiquitous biofilm characteristics make M. lacticum D84 a suitable model for biofilm research. Studying biofilm formation of these bacteria may help one understand bacterial adhesion on interfaces and hence reduce biofilm formation in the food industry.

Vacuum Casting and Mechanical Characterization of Nanocomposites from Epoxy and Oxidized Multi-Walled Carbon Nanotubes.

Sample preparation is an important step when testing the mechanical properties of materials. Especially, when carbon nanotubes (CNT) are added to epoxy resin, the increase in viscosity complicates the casting of testing specimens. We present a vacuum casting approach for different geometries in order to produce specimens from functional nanocomposites that consist of epoxy matrix and oxidized multi-walled carbon nanotubes (MWCNTs). The nanocomposites were characterized with various mechanical tests that showed improved fracture toughness, bending and tensile properties performance by addition of oxidized MWCNTs. Strengthening mechanisms were analyzed by SEM images of fracture surfaces and in-situ imaging by digital image correlation (DIC).

Acid Free Oxidation and Simple Dispersion Method of MWCNT for High-Performance CFRP.

Carbon nanotubes (CNT) provide an outstanding property spectrum which can be used to improve a wide range of materials. However, the transfer of properties from the nanoscale to a macroscopic material is a limiting factor. Different approaches of functionalizing the surface of a CNT can improve the interaction with the surrounding matrix but is connected to difficult and expensive treatments, which are usually inconvenient for industrial applications. Here, a simple and eco-friendly method is presented for the oxidation of CNT, where hydrogen peroxide (H2O2) is the only chemical needed and no toxic emissions are released. Also, the extensive step of the incorporation of CNT to an epoxy matrix is simplified to an ultrasonic dispersion in the liquid hardener component. The effectiveness is proven by mechanical tests of produced CNT/CFRP and compared to a conventional processing route. The combination of those simple and cost efficient strategies can be utilized to produce multiscale composites with improved mechanical performance in an ecological and economical way.

Strain Measurements within Fiber Boards. Part I: Inhomogeneous Strain Distribution within Medium Density Fiberboards (MDF) Loaded Perpendicularly to the Plane of the Board.

Internal bond strength testing is a widely used approach for testing quality traits of wood based panels. Generally, failure of internal bond specimens is due to adhesion and/or wood failure in the specimen. It has been reported that a composite product with a large variation in the vertical density profile fails in the center part of the board which is either the middle of the core layer or the transition zone between core layer and face layer. The density in the failure zone is typically 50% lower than the maximum density in the face layers. The aim of this study was to analyze the strain distribution in a specimen under tension perpendicular to the panel plane. The results showed that a high variety of strain magnitude occurred in the specimen. The strain is either aligned with the tension direction or a tension zone is built in one of the edge zones leading to failure. Vector graphics of the specimen show the problematic test setup of internal bond strength measurement. Strain spots in the edges lead to the assumption of an uneven stress distribution due to the momentum which results from non-perfect alignment or irregularities in the test setup.