A depth-resolved quantitative evaluation method for non-carious cervical lesions treatment with optical coherence tomography.

OBJECTIVES: The aim of this study is prognostic assessment of surface smoothness and the presence of internal bubbles after treatment of non-cancerous cervical lesions (NCCLs) using optical coherence tomography (OCT). METHODS: After treatment with NCCLs, cross-sectional images of the lesion parts of the sample were non-invasively acquired and analyzed. The surface smoothness between tooth and resin, resin and cemento-enamel junction, and the presence bubble inside resin was confirmed. In addition, using an algorithm that distinguishes between resin and dental structure based on OCT cross-sectional images, we quantitatively analyzed the amount of resin used in treating NCCLs and acquired 3D images. RESULTS: The inner structure of the resin in each sample was checked, and the presence of bubbles was confirmed. In addition, the resin sections were separated from the tomographic images acquired by OCT to visualize 3D images. The volume of resin used in the treatment part of each NCCLs samples was quantitatively analyzed as 3.7216 ∼ 14.889 mm3. CONCLUSIONS: OCT is able to measure not only the surface abrasion provided by existing intraoral scanner, but also the size and depth location of interal bubbles, which is distinctive advantage of our method. Based on our results, OCT is a significant tool for qualitative and quantitative analysis of dental NCCLs treatment before and after treatment. CLINICAL SIGNIFICANCE: The study used OCT, a non-destructive diagnostic, to reveal the structure of the resin and the location and size of bubbles after NCCLs treatment. These findings could be golden standard in determining the prognosis of NCCLs treatment.

Feasibility of images acquired using smartphone camera for marginal and internal fit of fixed dental prosthesis: comparison and correlation study.

This study aimed to measure marginal and internal fit using images captured with both an optical microscope and a smartphone camera, comparing the fit measurement performance of these devices and analyzing their correlation. Working casts (with 10 posterior and 10 anterior teeth) created to fabricate fixed dental prostheses were used. These working casts were scanned using a desktop scanner (E1) to design an interim crown, and the designed interim crown was fabricated using a three-dimensional (3D) printer. Utilizing the silicone replica technique, the fabricated interim crown replicated the fit, which was then captured using both an optical microscope and a smartphone camera. The captured images were used to measure the marginal and internal fit according to the imaging device. Intraclass correlation coefficients (ICC) were used for reliability analysis according to the imaging device. Furthermore, the Wilcoxon signed-rank test was adopted for the comparative evaluation of the marginal and internal fit between the imaging devices (α = 0.05). The measurement results of the marginal and internal fit according to the optical microscope and smartphone camera did exhibit a significant difference (P < 0.05). The ICC between the two devices showed an "excellent" agreement of over 0.9 at all measurement points (P < 0.001). A smartphone camera could be used to obtain images for evaluating the marginal and internal fit.

Evaluation of photopolymer resins for dental prosthetics fabricated via the stereolithography process at different polymerization temperatures. Part II: Dimensional accuracy and fracture load of fixed dental prostheses.

STATEMENT OF PROBLEM: Prostheses printed on a 3-dimensional (3D) printer need to undergo the postpolymerization process, which can increase the working time. However, it has been not suggested for reducing workload and improving the properties of prostheses in dental clinical practice. PURPOSE: The purpose of this in vitro study was to evaluate how the printing temperature impacts the dimensional accuracy and fracture load of 3D printed fixed dental prostheses (FDPs). MATERIAL AND METHODS: Dental prostheses were printed at room temperature (RT), 50°C, and 70°C using a stereolithography 3D printer. Subsequently, after rinsing away residual monomer, the printed parts underwent the green condition (it was not subjected to any postprocessing) and postpolymerization. The mechanical properties of the printed FDPs were determined by loading to fracture (n=6). To evaluate their clinical applicability, the dimensional accuracy and fit of FDPs fabricated at various resin polymerization temperatures were measured (n=6). The 1-way analysis of variance was used to perform statistical comparisons, followed by the Tukey honestly significant difference test (α=.05). RESULTS: The specimens printed at RT and 50°C were better than those printed at 70°C in terms of dimensional accuracy and fit (P<.05). Nonetheless, the dimensional accuracy and fit of the specimens printed at 70°C were clinically acceptable. The fracture load of the 3-unit FDPs depended significantly on the printing temperature. CONCLUSIONS: The dimensional accuracy and fracture load of the 70°C group were acceptable for FDP fabrication. Thus, the temperature of 70°C without postprocessing may help make the procedure more efficient.

Evaluation of photopolymer resins for dental prosthetics fabricated via the stereolithography process at different polymerization temperatures-Part I: Conversion rate and mechanical properties.

STATEMENT OF PROBLEM: Improvement in the mechanical properties of 3-dimensional (3D) printed dental prostheses is necessary to prevent wear caused by an antagonist or fracture. However, how different printing temperatures affect their mechanical properties is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the mechanical properties of 3D printed parts fabricated at different printing temperatures. MATERIAL AND METHODS: Photopolymer specimens were fabricated at 3 different temperatures (room temperature, 50 °C, and 70 °C) using a stereolithography 3D printer. After rinsing to remove the residual monomer, the specimens were divided into 2 groups: with or without postprocessing. The viscosity of the photopolymerization resin was measured while the temperature was increased. Furthermore, the double-bond conversion (DBC) of the printed part was evaluated (n=3). Mechanical properties were investigated via dynamic mechanical analysis (n=1) and tensile testing (n=5). Statistical comparisons were performed via 1-way analysis of variance, followed by the Tukey honestly significant difference test (α=.05). RESULTS: The DBC rates of the green condition group increased from 66.67% to 86.33% with increasing temperature. In addition, these specimens exhibited improved mechanical properties and reduced residual monomer levels. CONCLUSIONS: Specimens fabricated at a temperature of 70 °C exhibited mechanical properties suitable for clinical application.

Prediction of learning curves of wired and wireless intraoral scanners.

This clinical study aimed to predict the learning curve of wireless and wired intraoral scanners (IOSs) and to compare the reduction patterns of working time. Overall, 14 participants were enrolled in the study. The intraoral scanning procedure was repeated four times, each using wireless and wired IOSs (i700; MEDIT). The work time from the first to the 600th iterations was predicted using the Wright model. Regarding statistical analysis, the Mann-Whitney U-test was performed for comparison between wireless and wired IOSs and between groups with and without an IOS usage experience, and the Friedman test was performed to evaluate the time reduction (α = 0.05). There was a significant difference between wireless and wired IOSs in the first (P = 0.008) and the third (P = 0.035) iterations. Moreover, the time for 600 iterations was statistically significantly different between wireless and wired IOSs (P < 0.05); however, there was no significant difference after the sixth iteration (e.g., seventh iteration: P = 0.062). In wireless IOS, no significant difference was found between participants with and without an IOS usage experience after the 34th iteration (P = 0.053). The difference in the learning effect between wireless and wired IOSs can be overcome by initial learning; however, an IOS usage experience can affect the learning time of wireless IOSs.

A concept to detect a subgingival finish line using an intraoral optical coherence tomography system: A clinical report.

This clinical report introduces an approach for detecting the supragingival finish line by penetrating the teeth and gingival tissue using optical coherence tomography (OCT) technology. This approach was used in 3 patients who underwent tooth preparation with a subgingival finish line. Consequently, the subgingival finish line, typically challenging to discern clearly in intraoral scans, was identifiable in the OCT image.

Effect of Electrocautery and Laser Treatment on the Composition and Morphology of Surface-Modified Titanium Implants.

The purpose of this study was to investigate the effects of different peri-implantitis treatment methods (Er,Cr:YSGG laser, diode laser, and electrocautery) on various titanium implant surfaces: machined; sandblasted, large-grit, and acid-etched; and femtosecond laser-treated surfaces. Grade 4 titanium (Ti) disks, with a diameter of 10 mm and a thickness of 1 mm, were fabricated and treated using the aforementioned techniques. Subsequently, each treated group of disks underwent different peri-implantitis treatment methods: Er,Cr:YSGG laser (Biolase, Inc., Foothill Ranch, CA, USA), diode laser (Biolase, Inc., Foothill Ranch, CA, USA), and electrocautery (Ellman, Hicksville, NY, USA). Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and wettability were used to characterize the chemical compositions and surfaces of the treated titanium surfaces. Significant changes in surface roughness were observed in both the electrocautery (Sa value of machined surface = 0.469, SLA surface = 1.569, femtosecond laser surface = 1.741, and p = 0.025) and Er,Cr:YSGG laser (Ra value of machined surface = 1.034, SLA surface = 1.380, femtosecond laser surface = 1.437, and p = 0.025) groups. On femtosecond laser-treated titanium implant surfaces, all three treatment methods significantly reduced the surface contact angle (control = 82.2°, diode laser = 74.3°, Er,Cr:YSGG laser = 73.8°, electrocautery = 76.2°, and p = 0.039). Overall, Er,Cr:YSGG laser and electrocautery treatments significantly altered the surface roughness of titanium implant surfaces. As a result of surface composition after different peri-implantitis treatment methods, relative to the diode laser and electrocautery, the Er,Cr:YSGG laser increased oxygen concentration. The most dramatic change was observed after Er:Cr;YSGG laser treatment, urging caution for clinical applications. Changes in surface composition and wettability were observed but were not statistically significant. Further research is needed to understand the biological implications of these peri-implantitis treatment methods.

Does an ergonomic dentist stool design have a positive impact on musculoskeletal health during intraoral scans and tooth preparation?

PURPOSE: This study aimed to evaluate the effects of an ergonomic dentist stool design on muscle activity and fatigue in dentists. MATERIALS AND METHODS: Fourteen dentists were recruited, and electrodes were attached to the arm, neck, and shoulder muscles of these dentists according to the Surface ElectroMyoGraphy for the Non-Invasive Assessment of Muscles protocol. After measuring the maximal voluntary contraction, eight-channel surface electromyography was performed during simulations of two dental procedures (intraoral scanning and tooth preparation) while the dentists were using two types of dentist stools. Furthermore, muscle activity and fatigue were determined based on the eight-channel surface electromyography data, and ergonomic risk levels were evaluated according to the muscle activity. The Shapiro-Wilk test was used to confirm that all data were normally distributed, and the Mann-Whitney U test was used to compare the two types of dentist stools (α = 0.05). RESULTS: There was a significant difference between the conventional and ergonomically designed dentist stools in terms of the activity of trapezius descendens muscle (p < 0.05). Notably, the activity of the trapezius descendens muscle was lesser when the dentists used ergonomically designed dentist stools than when they used a conventional dentist stool. The activity of all muscles, except for the sternocleidomastoid, indicated moderate ergonomic risk. CONCLUSION: A dentist stool that enables dentists to maintain ergonomic posture should be used to prevent musculoskeletal disorders.

In Vitro Biofilm Formation on Zirconia Implant Surfaces Treated with Femtosecond and Nanosecond Lasers.

(1) Background: The purpose of this study was to evaluate how a zirconia implant surface treated with laser technology affects the degree of biofilm formation. (2) Methods: Experimental titanium (Ti) disks were produced that were sandblasted with large grit and acid-etched (T), and they were compared with zirconia (ZrO2) discs with a machined (M) surface topography; a hydrophilic surface topography with a femtosecond laser (HF); and a hydrophobic surface topography with a nanosecond laser (HN) (N = 12 per surface group). An in vitro three-species biofilm sample (Aggregatibacter actinomycetemcomitans (Aa), Porphyromonas gingivalis (Pg), Prevotella intermedia (Pi)) was applied to each disc type, and bacterial adhesion was assessed after 48 and 72 h of incubation using an anaerobic flow chamber model. Statistical significance was determined using the Kruskal-Wallis H test, with Bonferroni correction used for the post-hoc test (α = 0.05). (3) Results: Compared to the T group, the M group exhibited more than twice as many viable bacterial counts in the three-species biofilm samples (p < 0.05). In comparison to the T group, the HF group had significantly higher viable bacterial counts in certain biofilm samples at 48 h (Aa and Pi) and 72 h (Pi) (p < 0.05). The HN group had higher viable bacterial counts in Pi at 48 h (5400 CFU/mL, p < 0.05) than the T group (4500 CFU/mL), while showing significantly lower viable bacterial counts in Pg at both 48 (3010 CFU/mL) and 72 h (3190 CFU/mL) (p < 0.05). (4) Conclusions: The surface treatment method for zirconia discs greatly influences biofilm formation. Notably, hydrophobic surface treatment using a nanosecond laser was particularly effective at inhibiting Pg growth.

The Impact of Mechanical Debridement Techniques on Titanium Implant Surfaces: A Comparison of Sandblasted, Acid-Etched, and Femtosecond Laser-Treated Surfaces.

This study evaluated the effects of various mechanical debridement methods on the surface roughness (Ra) of dental implants, comparing femtosecond laser-treated surfaces with conventionally machined and sandblasted with large-grit sand and acid-etched (SLA) implant surfaces. The fabrication of grade 4 titanium (Ti) disks (10 mm in diameter and 1 mm thick) and the SLA process were carried out by a dental implant manufacturer (DENTIS; Daegu, Republic of Korea). Subsequently, disk surfaces were treated with various methods: machined, SLA, and femtosecond laser. Disks of each surface-treated group were post-treated with mechanical debridement methods: Ti curettes, ultrasonic scaler, and Ti brushes. Scanning electron microscopy, Ra, and wettability were evaluated. Statistical analysis was performed using the Kruskal-Wallis H test, with post-hoc analyses conducted using the Bonferroni correction (α = 0.05). In the control group, no significant difference in Ra was observed between the machined and SLA groups. However, femtosecond laser-treated surfaces exhibited higher Ra than SLA surfaces (p < 0.05). The application of Ti curette or brushing further accentuated the roughness of the femtosecond laser-treated surfaces, whereas scaling reduced the Ra in SLA surfaces. Femtosecond laser-treated implant surfaces, with their unique roughness and compositional attributes, are promising alternatives in dental implant surface treatments.

Influence of Dental Titanium Implants with Different Surface Treatments Using Femtosecond and Nanosecond Lasers on Biofilm Formation.

This study aimed to evaluate the impact of different surface treatments (machined; sandblasted, large grit, and acid-etched (SLA); hydrophilic; and hydrophobic) on dental titanium (Ti) implant surface morphology, roughness, and biofilm formation. Four groups of Ti disks were prepared using distinct surface treatments, including femtosecond and nanosecond lasers for hydrophilic and hydrophobic treatments. Surface morphology, wettability, and roughness were assessed. Biofilm formation was evaluated by counting the colonies of Aggregatibacter actinomycetemcomitans (Aa), Porphyromonas gingivalis (Pg), and Prevotella intermedia (Pi) at 48 and 72 h. Statistical analysis was conducted to compare the groups using the Kruskal-Wallis H test and the Wilcoxon signed-rank test (α = 0.05). The analysis revealed that the hydrophobic group had the highest surface contact angle and roughness (p < 0.05), whereas the machined group had significantly higher bacterial counts across all biofilms (p < 0.05). At 48 h, the lowest bacterial counts were observed in the SLA group for Aa and the SLA and hydrophobic groups for Pg and Pi. At 72 h, low bacterial counts were observed in the SLA, hydrophilic, and hydrophobic groups. The results indicate that various surface treatments affect implant surface properties, with the hydrophobic surface using femtosecond laser treatment exerting a particularly inhibitory effect on initial biofilm growth (Pg and Pi).

Dental diagnosis for inlay restoration using an intraoral optical coherence tomography system: A case report.

PATIENTS: The patient was a 32-year-old man who underwent amalgam restoration of the mandibular right second molar. An amalgam restoration fracture was diagnosed by intraoral optical coherence tomography (OCT), and pulp exposure was examined during cavity preparation. Subsequently, a definitive ceramic restoration was fabricated, and the marginal fit in the oral cavity was evaluated using the OCT system. DISCUSSION: The existing OCT system cannot acquire images inside the oral cavity because of the large probe size. However, the proposed intraoral OCT system can access the prostheses in the mandibular right second molar. Therefore, dental diagnosis for restoration treatment with dental prosthesis fracture, marginal gap, and pulp exposure after tooth preparation is possible using the proposed intraoral OCT system. CONCLUSIONS: The use of the intraoral OCT system improved dental diagnosis by allowing the dentist to confirm quantitative values through cross-sectional images, rather than that by determining a treatment plan after visual dental diagnosis.

Feasibility of using an intraoral scanner for a complete arch digital scan, part 2: A comparison of scan strategies.

STATEMENT OF PROBLEM: Various strategies for intraoral scanners (IOSs) can be used to scan the oral cavity. However, research on the scan range that can be clinically is lacking. PURPOSE: The purpose of this in vitro study was to compare the 3-dimensional (3D) distortion of complete arch scans as part of the scan strategy and analyze the clinically recommended scan range. MATERIAL AND METHODS: A computer-aided design (CAD) reference model was obtained with an industrial scanner. A CAD test model was obtained by using 6 IOSs (TRIOS2, TRIOS3, CS3500, CS3600, i500, and Primescan) to apply 2 scan strategies and 2 dental laboratory scanners (DOF and E1) (N=15). All the teeth were segmented in the reference model by using 3D inspection software (Geomagic control X). The 3D analysis was performed by aligning the test model to the reference model and evaluating the root mean square values of all segmented teeth. The Mann-Whitney U-test was performed for a statistical comparison of the 2 scan strategies (α=.05), the Kruskal-Wallis test (α=.05) was used to compare the scanners, and the Mann-Whitney U-test and Bonferroni correction method were used as post hoc tests (α=.0017). RESULTS: The 8 scanners obtained significant differences in the root mean square values of all teeth (P<.001). The root mean square value of IOSs increased from the left maxillary second molar to the right maxillary second molar. The difference in the 2 scan strategies showed different patterns depending on the IOS. CONCLUSIONS: Scan strategy 2 improved the accuracy of the IOSs. TRIOS2 and CS3500 are for single crowns; TRIOS3, CS3600, and i500 are for short-span prostheses; and Primescan is for long-span prostheses.

Marginal and Internal Fit and Intaglio Surface Trueness of Temporary Crowns Fabricated with Stereolithography, Digital Light Processing, and Milling Technology.

PURPOSE: To evaluate the fit and trueness of temporary crowns fabricated with 3D printing vs milling technologies and to analyze any existing correlations between fit and trueness. MATERIALS AND METHODS: Marginal and internal fit and trueness were evaluated. Groups were compared using Kruskal-Wallis H test (α = .05), and correlations were analyzed using Spearman rank correlation analysis (α = .0016). RESULTS: Intaglio surface trueness was partially correlated with the marginal and internal fit (P < .0016). CONCLUSION: High intaglio surface trueness in the axial and occlusal regions may result in poor marginal fit. In the axial region, high intaglio surface trueness may adversely affect both the marginal and internal fit.

Trueness of intraoral scanners according to subgingival depth of abutment for fixed prosthesis.

This study aimed to compare the trueness of intraoral scanners (IOSs) according to the subgingival finish line depth of tooth preparation for fixed prostheses. The prepared maxillary right first molar was fabricated by using ceramic material. A computer-aided design (CAD) reference model (CRM) of the abutment was obtained by using a contact scanner. The subgingival finish line was located according to the depth at 0-mm, 0.25-mm, 0.5-mm, 0.75-mm, and 1-mm. CAD test models (CTMs) were obtained by using 2 IOSs (i500 and CS3600). CRM and CTM were superimposed and analyzed (Geomagic control X). The one-way analysis of variance (ANOVA) was used to compare the trueness according to the subgingival finish line depth. The paired t test was used to compare the trueness of IOSs with and without gingival retraction (α = .05). When the gingival displacement code was not used, it was observed that the trueness of both IOSs decreased significantly as the depth of the subgingival finish line increased (P < 0.001). When the subgingival finish line was positioned deeper than 0.5-mm, the trueness of both IOSs exceeded 100 µm in the marginal region. When the gingival displacement cord was used, the trueness of both IOSs did not exceed 100 µm regardless of the subgingival finish line depth. When gingival cord was used, it showed significantly higher trueness than when not used (P < 0.001). When the gingival displacement cord was not used, the trueness of IOSs decreased as the subgingival finish line depth increased. But the use of the gingival displacement cord improved the scanning trueness by 90%. Thus, it is necessary to use the gingival displacement cord according to the clinical situation to improve scan trueness at the subgingival finish line.

Comparison of Osseointegration of Dental Implants Placed in Rabbit Tibia Using Two Dental Laser and Implant Handpiece Systems.

The present study aimed to confirm the usefulness of a multi-laser handpiece system currently under development. Implants were placed in the tibia of rabbits using a conventional separate laser-implant handpiece system (control group; SurgicPro+; NSK, Kanuma, Japan and Epic 10; Biolase, Irvine, CA, USA) and a multi-laser handpiece system (experimental group; BLP 10; Saeshin, Daegu, Korea). Implants were placed in left and right tibias of five rabbits using a conventional laser-implant handpiece system and a multi-laser handpiece system (N = 5 per group). Subsequently, micro-computed tomography (micro-CT; bone-to-implant contact evaluation), implant stability quotient (ISQ) measurement, and histological evaluations were performed to confirm the implant placement results. The independent t-test and the paired t-test were used to compare the ISQ values and the results of the two implant-laser handpiece groups (α = 0.05), respectively. No statistically significant difference in micro-CT, ISQ, and histological evaluations was observed between implant placement by the two systems (p > 0.05) except implant initial stability. The use of the multi-laser handpiece system is expected to produce the same results as a conventional separate laser-implant handpiece system with the higher implant initial stability. Additionally, it will potentially make the clinical environment more pleasant and will provide convenience for the clinicians.

Comparison of Wear of Interim Crowns in Accordance with the Build Angle of Digital Light Processing 3D Printing: A Preliminary In Vivo Study.

The aim of this study is to evaluate the wear volume of interim crowns fabricated using digital light processing 3D printing according to the printing angle. A total of five patients undergoing the placement of a single crown on the mandibular molar were included. Interim crowns were fabricated directly in the oral cavity using the conventional method. A digital light processing 3D printer was then used to fabricate crowns with build angles of 0, 45, and 90 degrees. Therefore, four fabricated interim crowns were randomly delivered to the patients, and each was used for one week. Before and after use, the intaglio surfaces of the interim crowns were scanned using a 3D scanner. The volume changes before and after use were measured, and changes in the height of the occlusal surface were evaluated using the root mean square value. Data normality was verified by statistical analysis, and the wear volume in each group was evaluated using a one-way analysis of variance and Tukey's honestly significant difference test (α = 0.05). Compared with the RMS values of the conventional method (11.88 ± 2.69 µm) and the 3D-printing method at 0 degrees (12.14 ± 2.38 µm), the RMS values were significantly high at 90 degrees (16.46 ± 2.39 µm) (p < 0.05). Likewise, there was a significant difference in the change in volume between the groups (p = 0.002), with a significantly higher volume change value at 90 degrees (1.74 ± 0.41 mm3) than in the conventional method (0.70 ± 0.15 mm3) (p < 0.05). A printing angle of 90 degrees is not recommended when interim crowns are fabricated using digital light processing 3D printing.

A Comparative Immunohistochemical Study of Wound Healing after Dental Diode Laser Treatment in the Rat Oral Mucosa.

This study aimed to examine the differences in healing patterns using two types of diode laser devices (laser A and laser B) and a steel scalpel for periodontal surgery through histological and immunohistochemical methods. Twenty 12-week-old male rats were assigned to three groups (3, 7, and 14 days). Square-shaped erosion wounds (2 × 2 mm2 diameter) were created on the hard palate of each rat. Two wounds were created using Laser A and a steel scalpel (Bard-Parker No. 15) on the right palate and using Laser B and a steel scalpel on the left side. Rats were sacrificed after 3, 7, and 14 days. Tissues were collected with a margin of 1 mm from the border of the erosional wound of the maxillary hard palate. Histological and immunohistochemical analyses were performed on the tissue samples after 3, 7, and 14 days. The tissue healing pattern and expression of inducible nitric oxide synthase (iNOS) and cluster of differentiation (CD) were observed under a light microscope. Statistical analysis was conducted using the Kruskal−Wallis H test for comparison among the groups (α = 0.05). In comparison to the wounds made with the scalpel, wounds treated with lasers A and B showed delayed healing patterns. There was no significant difference between the two laser treatment groups (p > 0.05). The expression of iNOS and CD68 was not significantly different among the three groups after 3 and 7 days (p > 0.05). On day 14, the groups treated with the dental diode lasers showed higher expression than the group treated with the steel scalpel, but no significant difference was observed (p > 0.05). Laser-induced wounds tended to heal slower than surgical wounds performed using a steel scalpel, but histological and immunohistochemical results showed no significant difference between the dental diode laser and scalpel groups.

How Does the Use of an Intraoral Scanner Affect Muscle Fatigue? A Preliminary In Vivo Study.

The purpose of this study was to evaluate muscle activation and fatigue in the operator during tooth preparation and intraoral scanning by simulating these tasks in two types of dental unit chair systems (UCS). Six participants were recruited, and the above tasks were simulated. Electrodes were placed on the skin over five types of muscles (arm, neck, and shoulder muscles), and the maximal voluntary contraction (MVC) was measured. Electromyography (EMG) was assessed during the simulation, and EMG values were normalized using MVC. The root mean square (RMS) EMG (%MVC) and muscle fatigue (%) were calculated. Owing to a lack of normal distribution of the data, Mann−Whitney U test and Kruskal−Wallis H test were performed for statistical comparison, and Bonferroni adjustment was performed for multiple comparisons (α = 0.05). There was no significant difference in RMS EMG between the two types of dental UCS (intraoral scanning, p = 0.237; tooth preparation, p = 0.543). Moreover, the RMS EMG and muscle fatigue were not significantly different between the two tasks (p > 0.05). There was significant muscle fatigue after the intraoral scanner use was simulated thrice (p < 0.001). It is necessary to refrain from performing continuous intraoral scanning and tooth preparation and to take appropriate rest to reduce the incidence of musculoskeletal disorders in dentists in clinical settings.

Satisfaction Factors with a Dental Unit Chair System in South Korea: A Dentist's Perspective.

This study aimed to survey users' satisfaction with a dental unit chair in order to highlight the elements affecting the dentist's satisfaction. The questionnaire items were drawn up with seven components that constitute a dental unit chair, including the light, patient seat, foot controller, water fountain and cuspidor, monitor, bracket table and controller, and dentist chair. With these questionnaire elements, a pilot experiment was conducted to test the reliability, and reliability analysis was conducted. The scale reliability was checked using Cronbach's alpha coefficient. Bartlett's test of sphericity, the Kaiser-Meyer-Olkin (KMO) measure, and factor analysis were performed to test whether the items would constitute appropriate questionnaire items for the survey. The survey was conducted with 26 dentists with more than three years of clinical experience. A correlation analysis was conducted using Pearson's correlation coefficient (PCC) (α = 0.05) to analyze the impact of the factors on the overall satisfaction with the dental unit chair. The items that were strongly correlated with the overall satisfaction score of the dental unit chair were the design and appearance quality of the dental unit chair (PCC = 0.781), its maintenance (PCC = 0.784), and the overall satisfaction with the water fountain and cuspidor (PCC = 0.703) (p < 0.05). Most of the questionnaire items could affect the overall satisfaction with the dental unit chair. Additionally, because the design and appearance quality, maintenance, and overall satisfaction with the water fountain and cuspidor may have the greatest impact on the overall satisfaction with the dental unit chair, the improvement of these elements may bring about the enhancement of the overall satisfaction.