Advanced Neuromorphic Applications Enabled by Synaptic Ion-Gating Vertical Transistors.

Bioinspired synaptic devices have shown great potential in artificial intelligence and neuromorphic electronics. Low energy consumption, multi-modal sensing and recording, and multifunctional integration are critical aspects limiting their applications. Recently, a new synaptic device architecture, the ion-gating vertical transistor (IGVT), has been successfully realized and timely applied to perform brain-like perception, such as artificial vision, touch, taste, and hearing. In this short time, IGVTs have already achieved faster data processing speeds and more promising memory capabilities than many conventional neuromorphic devices, even while operating at lower voltages and consuming less power. This work focuses on the cutting-edge progress of IGVT technology, from outstanding fabrication strategies to the design and realization of low-voltage multi-sensing IGVTs for artificial-synapse applications. The fundamental concepts of artificial synaptic IGVTs, such as signal processing, transduction, plasticity, and multi-stimulus perception are discussed comprehensively. The contribution draws special attention to the development and optimization of multi-modal flexible sensor technologies and presents a roadmap for future high-end theoretical and experimental advancements in neuromorphic research that are mostly achievable by the synaptic IGVTs.

Correction: Soda et al. Electrochemical Detection of Global DNA Methylation Using Biologically Assembled Polymer Beads. Cancers 2021, 13, 3787.

In the original publication [...].

Flexible Ink-Jet Printed Polymer Light-Emitting Diodes using a Self-Hosted Non-Conjugated TADF Polymer.

Thermally activated delayed fluorescent (TADF) emitters have become the leading emissive materials for highly efficient organic light-emitting diodes (OLEDs). The deposition of these materials in scalable and cost-effective ways is paramount when looking toward the future of OLED applications. Herein, a simple OLED with fully solution-processed organic layers is introduced, where the TADF emissive layer is ink-jet printed. The TADF polymer has electron and hole conductive side chains, simplifying the fabrication process by removing the need for additional host materials. The OLED has a peak emission of 502 nm and a maximum luminance of close to 9600 cd m-2 . The self-hosted TADF polymer is also demonstrated in a flexible OLED, reaching a maximum luminance of over 2000 cd m-2 . These results demonstrate the potential applications of this self-hosted TADF polymer in flexible ink-jet printed OLEDs and, therefore, for a more scalable fabrication process.

Hybrid 2D perovskite and red emitting carbon dot composite for improved stability and efficiency of LEDs.

Organic-inorganic hybrid lead trihalide perovskites have shown promise consistently in optoelectronic devices such as light-emitting diodes (LEDs), solar cells, photodetectors, sensors, and other optoelectronic devices. Perovskite-based LEDs (PSK-LEDs) have shown enormous potential, mostly due to their lower cost, easy synthesis via solution processibility, and highly tunable light-emitting behavior with higher performance. Despite the recent developments in green and blue PSK-LEDs over the years, there has been less development in the research area of red-emitting PSK-LEDs. Although some developments have led to spectrally, stable red-emitting PSK-LEDs, the stability of those devices still needs to be improved upon further for any practical application. In this work, to the best of our knowledge, for the first time, we used red-emitting 2D PSK as an active light-emitting layer which was further stabilized by red-emitting carbon dots (CDs). The CD-PSK composite films were used as an active layer in red emitting LEDs, and they showed high operational stability, and improved performance compared to the control device with only PSK film as the active layer. The composite device showed improved maximum luminescence (3011 cd m-2), charge density (330 mA cm-2), operational stability (8 hours), better EQE (10.2%), and low turn-on voltage of 2.6 V compared to the control device with maximum luminescence (1512 cd m-2), charge density (134 mA cm-2), operational stability (<2 hours), EQE (2.6%) and turn on voltage of 3.2 V. The low-cost hybrid approach using PSK building blocks together with CDs opens a new approach leading to a composite material, which has immense possibilities for tuning the structure further to maximize the performance.

Impact of Planar and Vertical Organic Field-Effect Transistors on Flexible Electronics.

The development of flexible and conformable devices, whose performance can be maintained while being continuously deformed, provides a significant step toward the realization of next-generation wearable and e-textile applications. Organic field-effect transistors (OFETs) are particularly interesting for flexible and lightweight products, because of their low-temperature solution processability, and the mechanical flexibility of organic materials that endows OFETs the natural compatibility with plastic and biodegradable substrates. Here, an in-depth review of two competing flexible OFET technologies, planar and vertical OFETs (POFETs and VOFETs, respectively) is provided. The electrical, mechanical, and physical properties of POFETs and VOFETs are critically discussed, with a focus on four pivotal applications (integrated logic circuits, light-emitting devices, memories, and sensors). It is pointed out that the flexible function of the relatively newer VOFET technology, along with its perspective on advancing the applicability of flexible POFETs, has not been reviewed so far, and the direct comparison regarding the performance of POFET- and VOFET-based flexible applications is most likely absent. With discussions spanning printed and wearable electronics, materials science, biotechnology, and environmental monitoring, this contribution is a clear stimulus to researchers working in these fields to engage toward the plentiful possibilities that POFETs and VOFETs offer to flexible electronics.

Organic Solar Cell With Efficiency Over 20% and VOC Exceeding 2.1 V Enabled by Tandem With All-Inorganic Perovskite and Thermal Annealing-Free Process.

Organic solar cells (OSCs) based on polymer donor and non-fullerene acceptor achieve power conversion efficiency (PCE) more than 19% but their poor absorption below 550 nm restricts the harvesting of high-energy photons. In contrast, wide bandgap all-inorganic perovskites limit the absorption of low-energy photons and cause serious below bandgap loss. Therefore, a 2-terminal (2T) monolithic perovskite/organic tandem solar cell (TSC) incorporating wide bandgap CsPbI2 Br is demonstrated as front cell absorber and organic PM6:Y6 blend as rear cell absorber, to extend the absorption of OSCs into high-energy photon region. The perovskite sub-cell, featuring a sol-gel prepared ZnO/SnO2 bilayer electron transporting layer, renders a high open-circuit voltage (VOC ). The VOC is further enhanced by employing thermal annealing (TA)-free process in the fabrication of rear sub-cell, demonstrating a record high VOC of 2.116 V. The TA-free Ag/PFN-Br interface in organic sub-cell facilitates charge transport and restrains nonradiative recombination. Consequently, a remarkable PCE of 20.6% is achieved in monolithic 2T-TSCs configuration, which is higher than that of both reported single junction and tandem OSCs, demonstrating that tandem with wide bandgap all-inorganic perovskite is a promising strategy to improve the efficiency of OSCs.

A paper-based optical sensor for the screening of viruses through the cysteine residues of their surface proteins: A proof of concept on the detection of coronavirus infection.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a serious threat to human health. Current methods such as reverse transcription polymerase chain reaction (qRT-PCR) are complex, expensive, and time-consuming. Rapid, and simple screening methods for the detection of SARS-CoV-2 are critically required to fight the current pandemic. In this work we present a proof of concept for, a simple optical sensing method for the screening of SARS-CoV-2 through its spike protein subunit S1. The method utilizes a target-specific extractor chip to bind the protein from the biological specimens. The disulfide bonds of the protein are then reduced into a biothiol with sulfhydryl (SH) groups that react with a blue-colored benzothiazole azo dye-Hg complex (BAN-Hg) and causes the spontaneous change of its blue color to pink which is observable by the naked eye. A linear relationship between the intensity of the pink color and the logarithm of reduced S1 protein concentration was found within the working range 130 ng.mL-1-1.3 pg mL-1. The lowest limit of detection (LOD) of the assay was 130 fg mL-1. A paper based optical sensor was fabricated by loading the BAN-Hg sensor onto filter paper and used to screen the S1 protein in spiked saliva and patients' nasopharyngeal swabs. The results obtained by the paper sensor corroborated with those obtained by qRT-PCR. The new paper-based sensing method can be extended to the screening of many viruses (e.g. the human immunodeficiency virus, the human polyomavirus, the human papilloma virus, the adeno associated viruses, the enteroviruses) through the cysteine residues of their capsid proteins. The new method has strong potential for screening viruses at pathology labs and in remote areas that lacks advanced scientific infrastructure. Further clinical studies are warranted to validate the new sensing method.

Surface Treatment of Inorganic CsPbI3 Nanocrystals with Guanidinium Iodide for Efficient Perovskite Light-Emitting Diodes with High Brightness.

The remarkable evolution of metal halide perovskites in the past decade makes them promise for next-generation optoelectronic material. In particular, nanocrystals (NCs) of inorganic perovskites have demonstrated excellent performance for light-emitting and display applications. However, the presence of surface defects on the NCs negatively impacts their performance in devices. Herein, we report a compatible facial post-treatment of CsPbI3 nanocrystals using guanidinium iodide (GuI). It is found that the GuI treatment effectively passivated the halide vacancy defects on the surface of the NCs while offering effective surface protection and exciton confinement thanks to the beneficial contribution of iodide and guanidinium cation. As a consequence, the film of treated CsPbI3 nanocrystals exhibited significantly enhanced luminescence and charge transport properties, leading to high-performance light-emitting diode with maximum external quantum efficiency of 13.8% with high brightness (peak luminance of 7039 cd m-2 and a peak current density of 10.8 cd A-1). The EQE is over threefold higher than performance of untreated device (EQE: 3.8%). The operational half-lifetime of the treated devices also was significantly improved with T50 of 20 min (at current density of 25 mA cm-2), outperforming the untreated devices (T50 ~ 6 min).

Organic Electrochemical Transistors for In Vivo Bioelectronics.

Organic electrochemical transistors (OECTs) are presently a focus of intense research and hold great potential in expanding the horizons of the bioelectronics industry. The notable characteristics of OECTs, including their electrolyte-gating, which offers intimate interfacing with biological environments, and aqueous stability, make them particularly suitable to be operated within a living organism (in vivo). Unlike the existing in vivo bioelectronic devices, mostly based on rigid metal electrodes, OECTs form a soft mechanical contact with the biological milieu and ensure a high signal-to-noise ratio because of their powerful amplification capability. Such features make OECTs particularly desirable for a wide range of in vivo applications, including electrophysiological recordings, neuron stimulation, and neurotransmitter detection, and regulation of plant processes in vivo. In this review, a systematic compilation of the in vivo applications is presented that are addressed by the OECT technology. First, the operating mechanisms, and the device design and materials design principles of OECTs are examined, and then multiple examples are provided from the literature while identifying the unique device properties that enable the application progress. Finally, one critically looks at the future of the OECT technology for in vivo bioelectronic applications.

Antibody coated conductive polymer for the electrochemical immunosensing of Human Cardiac Troponin I in blood plasma.

Cardiac troponin I (cTnI) is a sensitive biomarker for cardiovascular disease (CVD). Rapid determination of cTnI concentration in blood can greatly reduce the potential of significant heart damage and heart failure. Herein, we demonstrate a new electrochemical immunosensor for selective affinity binding and rapid detection of cTnI in blood plasma by an electrochemical method. A conductive film of "poly 2,5-bis(2-thienyl)3,4-diamine-terthiophene (PDATT)" was deposited onto an Indium Tin Oxide (ITO) electrode using chronoamperometry. Anti-cardiac troponin I antibody was then attached to the two amine (NH2) groups substituted on the central thiophene of terthiophene repeating unit of the polymer chain via amide bond formation. The gaps on the surface of the antibody coated immunosensor were backfilled with bovine serum albumin (BSA) to prevent nonspecific binding of interfering molecules. Differential pulse voltammetry (DPV) was used to determine cTnI upon the formation of cTnI immunocomplex on the sensing surface, appearing a peak at 0.27 V. The response range was 0.01-100 ng mL-1 with limit of quantification down to 0.01 ng mL-1. The developed immunosensor was used to determine cTnI in spiked blood plasma without interference from cardiac troponin T (cTnT). Therefore, this new sensor can be utilised for the detection of cTnI biomarker in pathological laboratories and points of care in less than 15 min.

Structural Geometry Variation of 1,4-Naphthalene-Based Co-Polymers to Tune the Device Performance of PVK-Host-Based OLEDs.

Blue-color-emitting organic semiconductors are of significance for organic light-emitting diodes (OLEDs). In this study, through Suzuki coupling polymerization, three 1,4-naphthalene-based copolymers-namely, PNP(1,4)-PT, PNP(1,4)-TF, and PNP(1,4)-ANT-were designed and synthesized. The variation of comonomers, phenothiazine (PT), triphenylamine substituted fluorene (TF), and anthanthrene (ANT), effectively tuned the emitting color and device performance of poly(9-vinyl carbazole) (PVK)-based OLEDs. Especially, the polymer PNP(1,4)-TF, bearing perpendicular aryl side groups, showed a most twisted structural geometry, which enabled an ultra-high thermal stability and a best performance with blue emitting in PVK-host-based OLEDs. Overall, in this work, we demonstrate a promising blue-color-emitting polymer through structural geometry manipulation.

Electrochemical Detection of Global DNA Methylation Using Biologically Assembled Polymer Beads.

DNA methylation is a cell-type-specific epigenetic marker that is essential for transcriptional regulation, silencing of repetitive DNA and genomic imprinting. It is also responsible for the pathogenesis of many diseases, including cancers. Herein, we present a simple approach for quantifying global DNA methylation in ovarian cancer patient plasma samples based on a new class of biopolymer nanobeads. Our approach utilises the immune capture of target DNA and electrochemical quantification of global DNA methylation level within the targets in a three-step strategy that involves (i) initial preparation of target single-stranded DNA (ss-DNA) from the plasma of the patients' samples, (ii) direct adsorption of polymer nanobeads on the surface of a bare screen-printed gold electrode (SPE-Au) followed by the immobilisation of 5-methylcytosine (5mC)-horseradish peroxidase (HRP) antibody, and (iii) immune capture of target ss-DNA onto the electrode-bound PHB/5mC-HRP antibody conjugates and their subsequent qualification using the hydrogen peroxide/horseradish peroxidase/hydroquinone (H2O2/HRP/HQ) redox cycling system. In the presence of methylated DNA, the enzymatically produced (in situ) metabolites, i.e., benzoquinone (BQ), binds irreversibly to cellular DNA resulting in the unstable formation of DNA adducts and induced oxidative DNA strand breakage. These events reduce the available BQ in the system to support the redox cycling process and sequel DNA saturation on the platform, subsequently causing high Coulombic repulsion between BQ and negatively charged nucleotide strands. Thus, the increase in methylation levels on the electrode surface is inversely proportional to the current response. The method could successfully detect as low as 5% methylation level. In addition, the assay showed good reproducibility (% RSD ≤ 5%) and specificity by analysing various levels of methylation in cell lines and plasma DNA samples from patients with ovarian cancer. We envision that our bioengineered polymer nanobeads with high surface modification versatility could be a useful alternative platform for the electrochemical detection of varying molecular biomarkers.

Energy-Level Manipulation in Novel Indacenodithiophene-Based Donor-Acceptor Polymers for Near-Infrared Organic Photodetectors.

Organic photodetectors (OPDs) are promising candidates for next-generation digital imaging and wearable sensors due to their low cost, tuneable optoelectrical properties combined with high-level performance, and solution-processed fabrication techniques. However, OPD detection is often limited to shorter wavelengths, whereas photodetection in the near-infrared (NIR) region is increasingly being required for wearable electronics and medical device applications. NIR sensing suffers from low responsivity and high dark currents. A common approach to enhance NIR photon detection is lowering the optical band gap via donor-acceptor (D-A) molecular engineering. Herein, we present the synthesis of two novel indacenodithiophene (IDT)-based D-A conjugated polymers, namely, PDPPy-IT and PSNT-IT via palladium-catalyzed Stille coupling reactions. These novel polymers exhibit optical band gaps of 1.81 and 1.27 eV for PDPPy-IT and PSNT-IT, respectively, with highly desirable visible and NIR light detection through energy-level manipulation. Moreover, excellent materials' solubility and thin-film processability allow easy incorporation of these polymers as an active layer into OPDs for light detection. In the case of PSNT-IT devices, a photodetection up to 1000 nm is demonstrated with a peak sensitivity centered at 875 nm, whereas PDPPy-IT devices are efficient in detecting the visible spectrum with the highest sensitivity at 660 nm. Overall, both OPDs exhibit spectral responsivities up to 0.11 A W-1 and dark currents in the nA cm-2 range. With linear dynamic ranges exceeding 140 dB and fast response times recorded below 100 µs, the use of novel IDT-based polymers in OPDs shows great potential for wearable optoelectronics.

e-MagnetoMethyl IP: a magnetic nanoparticle-mediated immunoprecipitation and electrochemical detection method for global DNA methylation.

The quantification of global 5-methylcytosine (5mC) content has emerged as a promising approach for the diagnosis and prognosis of cancers. However, conventional methods for the global 5mC analysis require large quantities of DNA and may not be useful for liquid biopsy applications, where the amount of DNA available is limited. Herein, we report magnetic nanoparticles-assisted methylated DNA immunoprecipitation (e-MagnetoMethyl IP) coupled with electrochemical quantification of global DNA methylation. Carboxyl (-COOH) group-functionalized iron oxide nanoparticles (C-IONPs) synthesized by a novel starch-assisted gel formation method were conjugated with anti-5mC antibodies through EDC/NHS coupling (anti-5mC/C-IONPs). Anti-5mC/C-IONPs were subsequently mixed with DNA samples, in which they acted as dispersible capture agents to selectively bind 5mC residues and capture the methylated fraction of genomic DNA. The target-bound Anti-5mC/C-IONPs were magnetically separated and directly adsorbed onto the gold electrode surface using gold-DNA affinity interaction. The amount of DNA adsorbed on the electrode surface, which corresponds to the DNA methylation level in the sample, was electrochemically estimated by differential pulse voltammetric (DPV) study of an electroactive indicator [Ru(NH3)6]3+ bound to the surface-adsorbed DNA. Using a 200 ng DNA sample, the assay could successfully detect differences as low as 5% in global DNA methylation levels with high reproducibility (relative standard deviation (% RSD) = <5% for n = 3). The method could also reproducibly analyze various levels of global DNA methylation in synthetic samples as well as in cell lines. The method avoids bisulfite treatment, does not rely on enzymes for signal generation, and can detect global DNA methylation using clinically relevant quantities of sample DNA without PCR amplification. We believe that this proof-of-concept method could potentially find applications for liquid biopsy-based global DNA methylation analysis in point-of-care settings.

Materials Design and Optimization for Next-Generation Solar Cell and Light-Emitting Technologies.

We review some of the most potent directions in the design of materials for next-generation solar cell and light-emitting technologies that go beyond traditional solid-state inorganic semiconductor-based devices, from both the experimental and computational standpoints. We focus on selected recent conceptual advances in tackling issues which are expected to significantly impact applied literature in the coming years. Specifically, we consider solution processability, design of dopant-free charge transport materials, two-dimensional conjugated polymeric semiconductors, and colloidal quantum dot assemblies in the fields of experimental synthesis, characterization, and device fabrication. Key modeling issues that we consider are calculations of optical properties and of effects of aggregation, including recent advances in methods beyond linear-response time-dependent density functional theory and recent insights into the effects of correlation when going beyond the single-particle ansatz as well as in the context of modeling of thermally activated fluorescence.

Facile Use of Silver Nanoparticles-Loaded Alumina/Silica in Nanofluid Formulations for Enhanced Catalytic Performance toward 4-Nitrophenol Reduction.

The introduction of toxic chemicals into the environment can result in water pollution leading to the degradation of biodiversity as well as human health. This study presents a new approach of using metal oxides (Al2O3 and SiO2) modified with a plasmonic metal (silver, Ag) nanoparticles (NPs)-based nanofluid (NF) formulation for environmental remediation purposes. Firstly, we prepared the Al2O3 and SiO2 NFs of different concentrations (0.2 to 2.0 weight %) by ultrasonic-assisted dispersion of Al2O3 and SiO2 NPs with water as the base fluid. The thermo-physical (viscosity, activation energy, and thermal conductivity), electrical (AC conductivity and dielectric constant) and physical (ultrasonic velocity, density, refractive index) and stability characteristics were comparatively evaluated. The Al2O3 and SiO2 NPs were then catalytically activated by loading silver NPs to obtain Al2O3/SiO2@Ag composite NPs. The catalytic reduction of 4-nitrophenol (4-NP) with Al2O3/SiO2@Ag based NFs was followed. The catalytic efficiency of Al2O3@Ag NF and SiO2@Ag NF, for the 4-NP catalysis, is compared. Based on the catalytic rate constant evaluation, the catalytic reduction efficiency for 4-NP is found to be superior for 2% weight Al2O3@Ag NF (92.9 × 10-3 s-1) as compared to the SiO2@Ag NF (29.3 × 10-3 s-1). Importantly, the enhanced catalytic efficiency of 2% weight Al2O3@Ag NF for 4-NP removal is much higher than other metal NPs based catalysts reported in the literature, signifying the importance of NF formulation-based catalysis.

Polyethylene Glycol Coated Magnetic Nanoparticles: Hybrid Nanofluid Formulation, Properties and Drug Delivery Prospects.

Magnetic nanoparticles (MNPs) are widely used materials for biomedical applications owing to their intriguing chemical, biological and magnetic properties. The evolution of MNP based biomedical applications (such as hyperthermia treatment and drug delivery) could be advanced using magnetic nanofluids (MNFs) designed with a biocompatible surface coating strategy. This study presents the first report on the drug loading/release capability of MNF formulated with methoxy polyethylene glycol (referred to as PEG) coated MNP in aqueous (phosphate buffer) fluid. We have selected MNPs (NiFe2O4, CoFe2O4 and Fe3O4) coated with PEG for MNF formulation and evaluated the loading/release efficacy of doxorubicin (DOX), an anticancer drug. We have presented in detail the drug loading capacity and the time-dependent cumulative drug release of DOX from PEG-coated MNPs based MNFs. Specifically, we have selected three different MNPs (NiFe2O4, CoFe2O4 and Fe3O4) coated with PEG for the MNFs and compared their variance in the loading/release efficacy of DOX, through experimental results fitting into mathematical models. DOX loading takes the order in the MNFs as CoFe2O4 > NiFe2O4 > Fe3O4. Various drug release models were suggested and evaluated for the individual MNP based NFs. While the non-Fickian diffusion (anomalous) model fits for DOX release from PEG coated CoFe2O4, PEG coated NiFe2O4 NF follows zero-order kinetics with a slow drug release rate of 1.33% of DOX per minute. On the other hand, PEG coated NiFe2O4 follows zero-order DOX release. Besides, several thermophysical properties and magnetic susceptibility of the MNFs of different concentrations have been studied by dispersing the MNPs (NiFe2O4, CoFe2O4 and Fe3O4) in the base fluid at 300 K under ultrasonication. This report on the DOX loading/release capability of MNF will set a new paradigm in view that MNF can resolve problems related to the self-heating of drug carriers during mild laser treatment with its thermal conducting properties.

A SERS quenching method for the sensitive determination of insulin.

In this work, we utilise the disulphide bond structure of insulin and a new benzothiazole Raman probe for the detection of human insulin using surface-enhanced Raman spectroscopy (SERS). The disulphide bond structure of the insulin was reduced to generate free sulfhydryl terminal groups. When reacted with benzothiazole-functionalised gold nanoparticles, the reduced protein desorbs the Raman probe and causes its Raman signal intensity to quench. Using this approach, insulin was quantified in the concentration range of 1 × 10-14 -1 × 10-8 M by SERS quenching. The limit of quantification of insulin by the SERS quenching method was found to be 1 × 10-14 M (0.01 pM or 58 pg/L), which satisfies the requirements for monitoring its blood concentration in patients. Because many proteins and peptides have disulphide bonds in their molecular structures, the new SERS quenching method has a strong potential for the rapid determination of ultralow concentrations of proteins in formulations and biological fluids.

Electrode and dielectric layer interface device engineering study using furan flanked diketopyrrolopyrrole-dithienothiophene polymer based organic transistors.

We successfully demonstrated a detailed and systematic enhancement of organic field effect transistors (OFETs) performance using dithienothiophene (DTT) and furan-flanked diketopyrrolopyrrole based donor-acceptor conjugated polymer semiconductor namely PDPPF-DTT as an active semiconductor. The self-assembled monolayers (SAMs) treatments at interface junctions of the semiconductor-dielectric and at the semiconductor-metal electrodes has been implemented using bottom gate bottom contact device geometry. Due to SAM treatment at the interface using tailored approach, the significant reduction of threshold voltage (Vth) from - 15.42 to + 5.74 V has been observed. In addition to tuning effect of Vth, simultaneously charge carrier mobility (µFET) has been also enhanced the from 9.94 × 10-4 cm2/Vs to 0.18 cm2/Vs. In order to calculate the trap density in each OFET device, the hysteresis in transfer characteristics has been studied in detail for bare and SAM treated devices. Higher trap density in Penta-fluoro-benzene-thiol (PFBT) treated OFET devices enhances the gate field, which in turn controls the charge carrier density in the channel, and hence gives lower Vth = + 5.74 V. Also, PFBT treatment enhances the trapped interface electrons, which helps to enhance the mobility in this OFET architecture. The overall effect has led to possibility of reduction in the Vth with simultaneous enhancements of µFET in OFETs, following systematic device engineering methodology.

Pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP) End Capped with Napthalimide or Phthalimide: Novel Small Molecular Acceptors for Organic Solar Cells.

We introduce two novel solution-processable electron acceptors based on an isomeric core of the much explored diketopyrrolopyrrole (DPP) moiety, namely pyrrolo[3,2-b]pyrrole-1,4-dione (IsoDPP). The newly designed and synthesized compounds, 6,6'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)-1H-benzo[de]isoquinoline-1,3(2H)-dione] (NAI-IsoDPP-NAI) and 5,5'-[(1,4-bis{4-decylphenyl}-2,5-dioxo-1,2,4,5-tetrahydropyrrolo[3,2-b]pyrrole-3,6-diyl)bis(thiophene-5,2-diyl)]bis[2-(2-butyloctyl)isoindoline-1,3-dione] (PI-IsoDPP-PI) have been synthesized via Suzuki couplings using IsoDPP as a central building block and napthalimide or phthalimide as end-capping groups. The materials both exhibit good solubility in a wide range of organic solvents including chloroform (CF), dichloromethane (DCM), and tetrahydrofuran (THF), and have a high thermal stability. The new materials absorb in the wavelength range of 300-600 nm and both compounds have similar electron affinities, with the electron affinities that are compatible with their use as acceptors in donor-acceptor bulk heterojunction (BHJ) organic solar cells. BHJ devices comprising the NAI-IsoDPP-NAI acceptor with poly(3-n-hexylthiophene) (P3HT) as the donor were found to have a better performance than the PI-IsoDPP-PI containing cells, with the best device having a VOC of 0.92 V, a JSC of 1.7 mAcm-2, a FF of 63%, and a PCE of 0.97%.