RESUMO
Employing functional and structured thin films on fiber optic sensors has tremendously improved capabilities in humidity sensing applications. In this paper, we demonstrate fabrication of a fiber optic evanescent wave humidity sensor based on S i O 2/porous polymethyl methacrylate (PMMA) thin films. With the exposure to moisture, S i O 2/porous PMMA thin films absorb water molecules. The refractive index and absorption coefficient of thin films change with ambient humidity, resulting in modulation of the light intensity transmitted in fiber. A good linearity is determined between the logarithm of output light intensity and relative humidity (RH). An optimal average sensitivity of 188.3 lux/%RH is achieved with an increase of 11.7 fold in the RH range of 5% to 95%. The response and recovery times are 8 s and 23 s, respectively. Furthermore, the sensor exhibits low hysteresis, and excellent stability and repeatability.
RESUMO
A fiber optic humidity sensor based on polyvinyl alcohol (PVA)/Tween 20 film has been fabricated by modulating the intensity of light transmitted in optical fiber. PVA/Tween 20 film was used as the cladding and humidity-sensitive material of optical fiber. The logarithmic of output light intensity exhibited a linear increase with the increase of humidity (22%-82%RH). With the addition of Tween 20 in the formation of film, average sensitivity increased by 13-fold. Fast equilibrium on adsorption and desorption of water molecules were also achieved on the film. The response and recovery times were determined to be 11 s and 9 s, respectively. Moreover, the sensor possesses good repeatability. The sensing mechanism was probably based on the swelling of PVA after adsorbing water molecules, which affected scattering of evanescent waves in the cladding. The output light intensity varied with the decay of evanescent waves.
RESUMO
Bi5O7I/g-C3N4 p-n junctioned photocatalysts were synthesized by alcohol-heating and calcination in air. The structures, morphologies and optical properties of as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (DRS). Photocatalytic activity of the heterojunctioned composites were evaluated by degradation of Rhodamine B (RhB) and tetracycline hydrochloride (TCH) under visible light illumination. The results indicated that the composites exhibited superior efficiencies for photodegradation of RhB and TCH in comparison with pure BiOI, Bi5O7I and g-C3N4. An effective built-in electric field was formed by the interface between p-type Bi5O7I and n-type g-C3N4, which promoted the efficient separation of photoinduced electron-hole pairs. In addition, 8% Bi5O7I/g-C3N4 composite showed excellent photostability in a five-cycle photocatalytic experiment. Experiments on scavenging active intermediates revealed the roles of active species.
RESUMO
A SiO2/TiO2 bilayer thin-film-based fiber optic humidity sensor was fabricated via a modified dip coating process with enhanced sensitivity. SiO2 film was coated on the surface of the fiber core, followed by deposition of the TiO2 layer on SiO2. The relative humidity (RH) is measured by modulation in intensity of the transmitted laser at room temperature. The optical fiber humidity sensor based on SiO2/TiO2 film shows two-segmented linearity in measurement with sensitivities of 5.35 and 1.94 µW/% RH at 15%-50% RH and 50%-95% RH, respectively. The response time and recovery time are 25 s and 50 s, respectively. To our knowledge, the superior response time and recovery time of the sensor in our study were achieved over those fiber optic humidity sensors reported with modulation in intensity. Furthermore, this fiber optic humidity sensor has a good reproducibility and long-term stability. The sensing mechanism is attributed to effects of moisture on the refractive index and the light absorption coefficient of SiO2 film and modulation in the transmission characteristic of evanescent waves in the optical fiber.
