Multi-objective optimization to improve energy, economic and, environmental life cycle assessment in waste-to-energy plant.

This paper presents a multi-objective optimization (MOO) of waste-to-energy (WtE) to investigate optimized solutions for thermal, economic, and environmental objectives. These objectives are represented by net efficiency, total cost in treating waste, and environmental impact. Integration of the environmental objective is conducted using life cycle assessment (LCA) with endpoint single score method covering direct combustion, reagent production and infrastructure, ash management, and energy recovery. Initial net efficiency of the plant was 16.27% whereas the cost and environmental impacts were 75.63 €/ton-waste and -1.21 × 108 Pt/ton-waste, respectively. A non-dominated sorting genetic algorithm (NSGA-II) is applied to maximize efficiency, minimize cost, and minimize environmental impact. Highest improvement for single objective is about 13.4%, 10.3%, and 14.8% for thermal, economic, and environmental, respectively. These improvements cannot be made at once since the objectives are conflicting. These findings highlight the significance role of decision makers in assigning weight to each objective function to obtain the optimal solution. The study also reveals different influence among decision variable, waste input, and marginal energy sources. Finally, this paper underlines the versatility of using MOO to improve WtE performance regarding the thermal, economic, and environmental aspects without requiring additional investment.

Enhancing Capillary-Driven Flow for Paper-Based Microfluidic Channels.

Paper-based microfluidic devices have received considerable interest due to their benefits with regards to low manufacturing costs, simplicity, and the wide scope of applications. However, limitations including sample retention in paper matrix and evaporation as well as low liquid flow rates have often been overlooked. This paper presents a paper-based capillary-driven flow system that speeds up flow rates by utilizing narrow gap geometry between two parallel surfaces separated by a spacer. The top surface is hydrophobic, while the bottom surface is a hydrophobic paper substrate with a microfluidic channel defined by a hydrophilic pathway, leaving sides of the channel open to air. The liquid flows on the hydrophilic path in the gap without spreading onto the hydrophobic regions. The closed-channel flow system showed higher spreading distances and accelerated liquid flow. An average flow rate increases of 200 and 100% were obtained for the nanoparticle-coated paperboard and the blotting papers used, respectively. Fast liquid delivery to detection zones or reaction implies rapid results from analytical devices. In addition, liquid drying and evaporation can be reduced in the proposed closed-channel system.

Heat and mass transfer models to understand the drying mechanisms of a porous substrate.

While drying of paper and paper coatings is expensive, with significant energy requirements, the rate controlling mechanisms are not currently fully understood. Two two-dimensional models are used as a first approximation to predict the heat transfer during hot air drying and to evaluate the role of various parameters on the drying rates of porous coatings. The models help determine the structural limiting factors during the drying process, while applying for the first time the recently known values of coating thermal diffusivity. The results indicate that the thermal conductivity of the coating structure is not the controlling factor, but the drying rate is rather determined by the thermal transfer process at the structure surface. This underlines the need for ensuring an efficient thermal transfer from hot air to coating surface during drying, before considering further measures to increase the thermal conductivity of porous coatings.

Paper-based microfluidics: fabrication technique and dynamics of capillary-driven surface flow.

Paper-based devices provide an alternative technology for simple, low-cost, portable, and disposable diagnostic tools for many applications, including clinical diagnosis, food quality control, and environmental monitoring. In this study we report a two-step fabrication process for creating two-dimensional microfluidic channels to move liquids on a hydrophobized paper surface. A highly hydrophobic surface was created on paper by TiO2 nanoparticle coating using a high-speed, roll-to-roll liquid flame spray technique. The hydrophilic pattern was then generated by UV irradiation through a photomask utilizing the photocatalytic property of TiO2. The flow dynamics of five model liquids with differing surface tensions 48-72 mN·m(-1) and viscosities 1-15 mN·m(-2) was studied. The results show that the liquid front (l) in a channel advances in time (t) according to the power law l=Zt0.5 (Z is an empirical constant which depend on the liquid properties and channel dimensions). The flow dynamics of the liquids with low viscosity show a dependence on the channel width and the droplet volume, while the flow of liquids with high viscosity is mainly controlled by the viscous forces.

Temperature effects on dynamic water absorption into paper.

Mechanisms controlling short time water absorption and the effect of temperature on water absorption into paper were investigated by analyzing previously published data. A dynamic contact angle effect caused by contact line friction explained the liquid uptake dynamics at short times. The water absorption rate increase with temperature is suggested to be controlled by the molecular processes occurring in front of the advancing liquid front. The increase in the non-equilibrium vapor pressure at air-liquid interface leads to higher water molecule adsorption onto fibers and associated lowering of the solid-gas interfacial tension, thereby increasing the wetting velocity and water absorption. The classical Lucas-Washburn equation was found to be inadequate for predicting water absorption into paper both at short times and as a function of temperature.