Off-stoichiometry in I-III-VI2 chalcopyrite absorbers: a comparative analysis of structures and stabilities.

Chalcopyrite Cu(In,Ga)Se2 (CIGSe) solar absorbers are renowned for delivering high solar power conversion efficiency despite containing high concentration of lattice defects amounting to copper deficiencies of several atomic percent. The unique ability to incorporate this deficiency without triggering decomposition (i.e. "tolerance to off-stoichiometry") is viewed by many as the key feature of CIGSe. In principle, this property could benefit any solar absorber, but remarkably little attention has been paid to it so far. In this study, we assess the tolerance to off-stoichiometry of thin-film photovoltaic materials by carrying out ab initio analysis of group-I-poor ordered defect compounds (ODCs) in the extended family of I-III-VI systems (where I = Cu, Ag, III = Al, Ga, In, and VI = S, Se, Te). We analyze convex hulls and structural evolution with respect to group-I content, link them with experimental phase diagrams, and determine two empirical principles for the future identification of solar energy materials with high tolerance to off-stoichiometry. Practical implications for the deposition of I-III-VI absorbers are also discussed in light of our computational results and recent experimental findings.

Experimental and Theoretical Study of Stable and Metastable Phases in Sputtered CuInS2.

The chalcopyrite Cu(In,Ga)S2 has gained renewed interest in recent years due to the potential application in tandem solar cells. In this contribution, a combined theoretical and experimental approach is applied to investigate stable and metastable phases forming in CuInS2 (CIS) thin films. Ab initio calculations are performed to obtain formation energies, X-ray diffraction (XRD) patterns, and Raman spectra of CIS polytypes and related compounds. Multiple CIS structures with zinc-blende and wurtzite-derived lattices are identified and their XRD/Raman patterns are shown to contain overlapping features, which could lead to misidentification. Thin films with compositions from Cu-rich to Cu-poor are synthesized via a two-step approach based on sputtering from binary targets followed by high-temperature sulfurization. It is discovered that several CIS polymorphs are formed when growing the material with this approach. In the Cu-poor material, wurtzite CIS is observed for the first time in sputtered thin films along with chalcopyrite CIS and CuAu-ordered CIS. Once the wurtzite CIS phase has formed, it is difficult to convert into the stable chalcopyrite polymorph. CuIn5 S8 and NaInS2 accommodating In-excess are found alongside the CIS polymorphs. It is argued that the metastable polymorphs are stabilized by off-stoichiometry of the precursors, hence tight composition control is required.

Chemistry of Oxygen Ionosorption on SnO2 Surfaces.

Ionosorbed oxygen is the key player in reactions on metal-oxide surfaces. This is particularly evident for chemiresistive gas sensors, which operate by modulating the conductivity of active materials through the formation/removal of surface O-related acceptors. Strikingly though, the exact type of species behind the sensing response remains obscure even for the most common material systems. The paradigm for ab initio modeling to date has been centered around charge-neutral surface species, ignoring the fact that molecular adsorbates are required to ionize to induce the sensing response. Herein, we resolve this inconsistency by carrying out a careful analysis of all charged O-related species on three naturally occurring surfaces of SnO2. We reveal that two types of surface acceptors can form spontaneously upon the adsorption of atmospheric oxygen: (i) superoxide O2- on the (110) and the (101) surfaces and (ii) doubly ionized O2- on the (100) facet, with the previous experimental evidence pointing to the latter as the source of sensing response. This species has a unique geometry involving a large displacement of surface Sn, forcing it to attain the coordination resembling that of Sn2+ in SnO, which seems necessary to stabilize O2- and activate metal-oxide surfaces for gas sensing.

Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells-Insight from Theory and Experiment.

Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.

Energy, Phonon, and Dynamic Stability Criteria of Two-Dimensional Materials.

First-principles calculations have become a powerful tool to exclude the Edisonian approach in search of novel two-dimensional (2D) materials. However, no universal first-principles criteria to examine the realizability of hypothetical 2D materials have been established in the literature yet. Because of this, and as the calculations are always performed in an artificial simulation environment, one can unintentionally study compounds that do not exist in experiments. Although investigations of physics and chemistry of unrealizable materials can provide some fundamental knowledge, the discussion of their applications can mislead experimentalists for years and increase the gap between experimental and theoretical research. By analyzing energy convex hull, phonon spectra, and structure evolution during ab initio molecular dynamics simulations for a range of synthesized and recently proposed 2D materials, we construct energy, phonon, and dynamic stability filters that need to be satisfied before proposing novel 2D compounds. We demonstrate the power of the suggested filters for several selected 2D systems, revealing that some of them cannot be ever realized experimentally.

Suppression of surfaces states at cubic perovskite (001) surfaces by CO2 adsorption.

By using first-principles approach, the interaction of CO2 with (001) surfaces of six cubic ABO3 perovskites (A = Ba, Sr and B = Ti, Zr, Hf) is studied in detail. We show that CO2 adsorption results in the formation of highly stable CO3-like complexes with similar geometries for all investigated compounds. This reaction leads to the suppression of the surfaces states, opening the band gaps of the slab systems up to the corresponding bulk energy limits. For most AO-terminated ABO3(001) perovskite surfaces, a CO2 coverage of 0.25 was found to be sufficient to fully suppress the surface states, whereas the same effect can only be achieved at 0.50 CO2 coverage for the BO2-terminated surfaces. The largest band gap modulation among the AO-terminated surfaces was found for SrHfO3(001) and BaHfO3(001), whereas the most profound effect among the BO2-terminated surfaces was identified for SrTiO3(001) and BaTiO3(001). Based on these results and considering practical difficulties associated with measuring conductivity of highly resistive materials, TiO2-terminated SrTiO3(001) and BaTiO3(001) were identified as the most prospective candidates for chemiresistive CO2 sensing applications.

Tailoring electronic properties of multilayer phosphorene by siliconization.

Controlling the thickness dependence of electronic properties for two-dimensional (2d) materials is among the primary goals for their large-scale applications. Herein, employing a first-principles computational approach, we predict that Si interaction with multilayer phosphorene (2d-P) can result in the formation of highly stable 2d-SiP and 2d-SiP2 compounds with a weak interlayer interaction. Our analysis demonstrates that these systems are semiconductors with band gap energies that can be governed by varying the thicknesses and stacking arrangements. Specifically, the siliconization of phosphorene allows designing 2d-SiPx materials with a significantly weaker thickness dependence of electronic properties than that in 2d-P and to develop ways for their tailoring. We also reveal the spatial dependence of electronic properties for 2d-SiPx highlighting the difference in the effective band gaps for different layers. Particularly, our results show that the central layers in the multilayer 2d systems determine their overall electronic properties, while the role of the outermost layers is noticeably smaller.

Band gap modulation of SrTiO3 upon CO2 adsorption.

Herein, CO2 chemisorption on SrTiO3(001) surfaces is studied using ab initio calculations to establish new chemical sensing mechanisms. It was found that CO2 adsorption opens the band gap of the material. However, the mechanisms are different: the CO2 adsorption on the TiO2-terminated surface neutralizes the surface states at the valence band (VB) maximum, whereas for the SrO-terminated surface it suppresses the conduction band (CB) minimum. For the TiO2-terminated surface, the effect is explained by the passivation of dangling bonds, whereas for the SrO-terminated surface, the suppression is caused by surface relaxation. Modulation of the VB states implies a more direct change in charge distribution, and thus, the induced change in the band gap is more prominent at the TiO2 termination. Further, it has been shown that both CO2 adsorption energy and surface band gap are strongly dependent on CO2 coverage, suggesting that the observed effect can be utilized in sensing applications for a wide range of CO2 concentrations.

Stability and electronic properties of phosphorene oxides: from 0-dimensional to amorphous 2-dimensional structures.

Combining the screening by first-principles calculations and Born-Oppenheimer molecular dynamics simulations, we fully reconsider phosphorene oxidation and the formation of low-dimensional phosphorus oxides (PxOy). It is found that the previously reported 2-dimensional PxOy (2d-PxOy) structures cannot provide a full understanding of 2d-PxOy properties. We show that the P-O interaction can result in highly stable 0d-PxOy and 2d-PxOy structures with close energetics, but a noticeable difference in band-gap energies. Here, the possibility of the formation of amorphous 2d-PxOy structures and their unique electronic properties are also studied in detail.

Ferroelectric KNbO3 nanofibers: synthesis, characterization and their application as a humidity nanosensor.

By virtue of its non-toxicity, high T c, and non-linear optical and ferroelectric properties, one-dimensional (1D) potassium niobate (KNbO3) may enable the development of numerous nanoscale devices. Despite the progress in 1D perovskite materials, preparing high aspect ratio KNbO3 nanostructures is still a concern. This report presents the successful synthesis of ultra-long KNbO3 nanofibers using a simple sol-gel assisted far-field electrospinning process. At optimized conditions, centimeters long, orthorhombic KNbO3 nanofibers with an average diameter of 100 nm have been obtained. The nanofibers are composed of uniform grains densely stacked along the direction of the nanofiber axis. Due to large surface-volume ratio, a high sensitive humidity nanosensor based on KNbO3 nanofibers displaying a logarithmic-linear dependence behavior of the conductance with the relative humidity (RH) was demonstrated. The conductance increases dramatically from 10(-10) ℧ to 10(-6) ℧ while RH varies from 15% to 95% at room temperature. In addition, the nanosensor exhibits excellent sensing performance, including ultrafast response (≤2 s) and recovery times (≤10 s), good linearity and reproducibility. Furthermore, the change in ferroelectric coercivity with respect to the RH and its effect in the sensing behavior were unveiled. This work could enable broad applications in the fields of environmental sensing and nano-electrical-mechanical systems.