Mechanical Properties Degradation of Fiberglass Tubes during Biaxial Proportional Cyclic Loading.

Composite structures during an operation are subjected to various types of external loading (impact, vibration, cyclic, etc.), which may lead to a decrease in mechanical properties. Previously, many experimental investigations of the mechanical behavior of composites under uniaxial cyclic loading were carried out. Acquisition of new data on the reduction of composite materials' mechanical characteristics under conditions of multiaxial cyclic loading, as well as verification of existing models for calculation of the residual properties, are relevant. Therefore, this work is devoted to the experimental investigation of the mechanical behavior of fiberglass tubes under proportional cyclic loading. Static and fatigue tests were carried out under tension with torsion conditions. Inhomogeneous strain fields were obtained using a non-contact optical video system VIC-3D. The structural damage accumulation processes were analyzed by an AMSY-6 acoustic emission signals recording system. Surface defects were determined using a DinoLite microscope. Residual dynamic elastic modules were calculated during fatigue tests, and fatigue sensitivity curves were built. Data was approximated using various models, and their high descriptive capability was revealed. Damage accumulation stages were determined. The dependence of the models' parameters on a stress state were observed. It was concluded that multiaxial cyclic loading leads to a significant decrease in mechanical properties, which should be taken into account in composite structure design.

Stability of Postcritical Deformation of CFRP under Static ±45° Tension with Vibrations.

The paper presents an experimental study on regularities of postcritical deformation of carbon-fiber-reinforced plastic (CFRP) under static ±45° tension. The employed test method is based on ASTM D3518. Displacement and strain fields were identified by a digital image correlation method (DIC) using a VIC-3D contactless optical video system. Acoustic emission signals were obtained using an AMSY-6 system. The surface analysis of samples was carried out using a CarlZeiss SteREO Discovery. V12 optical stereomicroscope and a DinoLite microscope. Three experimental test types were considered: active loading, deformation with unloadings, and tension under additional torsion vibrations with various amplitudes. Loading diagrams were constructed; they showed a number of stages in the damage accumulation process. It was analyzed how heterogeneous strain fields develop; a neck development during softening process was observed. It was noted that the loading system rigidity influences the failure moment. The research considered various shear strain calculation methods using a "virtual extensometer" instrument. Composite mechanical properties were obtained. A shear modulus reduction during a plastic strain increase was revealed. The acoustic emission signals were analyzed; three characteristic frequency bands were observed. Most of the contribution to cumulative energy was made by matrix cracking. A reduction of the number of AE signals associated with the violation of adhesion between the fibers and the matrix during postcritical deformation was observed. The research identified basic surface defects. An appearance of the defects corresponds with their identification by the AE system. It was revealed that the presence of additional torsion vibration leads to an increase in the softening stage length. It was concluded that due regard for the postcritical deformation stage and the loading system rigidity is reasonable during the structure strength analysis.

Anisotropy of Mechanical Properties and Residual Stress in Additively Manufactured 316L Specimens.

In the presented study, LPBF 316L stainless steel tensile specimens were manufactured in three different orientations for the analysis of anisotropy. The first set of specimens was built vertically on the build platform, and two other sets were oriented horizontally perpendicular to each other. Tensile test results show that mean Young's modulus of vertically built specimens is significantly less then horizontal ones (158.7 GPa versus 198 GPa), as well as yield strength and elongation. A role of residual stress in a deviation of tensile loading diagrams is investigated as a possible explanation. Simulation of the build process on the basis of ABAQUS FEA software was used to predict residual stress in 316L cylindrical specimens. Virtual tensile test results show that residual stress affects the initial stage of the loading curve with a tendency to reduce apparent Young's modulus, measured according to standard mechanical test methods.

Anatomical modeling of the foreskin for the reconstruction of glanular hypospadias.

The normal development of the glanular urethra is closely related to the normal development of the foreskin. A ventral deficit in the foreskin results with the failure to develop the septum glandis and frenulum, which also form the ventral wall of the glanular and subcoronal urethra. Here we present the anatomical modeling of the foreskin in order to obtain a mucosal collar for the reconstruction of the glanular hypospadias with the GFC technique (Glanular-Frenular-Collar), which can also be used for various purposes to reconstruct the urethra in hypospadias.

A closer look at iatrogenic hypospadias.

Almost all surgical repair techniques for hypospadias include dissection of the glans penis, and covering the neo-urethra with the glans tissue circumferentially. Surprisingly, the presence of the "septum glandis" in the ventral midline has been overlooked for decades. A careful examination of six patients with iatrogenic hypospadias (IH) revealed direct indications of the septum glandis. All patients were treated with long-term urethral catheterisation in the paediatric intensive care unit due to neurologic and/or metabolic diseases. The glans was disrupted in all patients due to ventral midline compression of the urethral catheter, which resulted in a tear in the septum glandis. A remnant of the septum glandis was clearly observed in patients with an incomplete tear. Further injuries caused tear in the frenulum and corpus spongiosum, exposed the glanular urethra and made its vertical elliptical shape, the "fossa navicularis", visible. Intact contours of the separated glans wings were observed in all patients. The glans wings merge ventrally in the midline, but are separated by a fine connective tissue (septum glandis) in conjunction with the frenulum, which is involved in the formation of the ventral wall of the glanular urethra. IH provides further insight into the structural anatomy of the normal human glans and glanular urethra.