Electrospinning Fabrication and Cytocompatibility Investigation of Nanodiamond Particles-Gelatin Fibrous Tubular Scaffolds for Nerve Regeneration.

This paper reports the electrospinning fabrication of flexible nanostructured tubular scaffolds, based on fish gelatin (FG) and nanodiamond nanoparticles (NDs), and their cytocompatibility with murine neural stem cells. The effects of both nanofiller and protein concentration on the scaffold morphology, aqueous affinity, size modification at rehydration, and degradation are assessed. Our findings indicate that nanostructuring with low amounts of NDs may modify the fiber properties, including a certain regional parallel orientation of fiber segments. NE-4C cells form dense clusters that strongly adhere to the surface of FG50-based scaffolds, while also increasing FG concentration and adding NDs favor cellular infiltration into the flexible fibrous FG70_NDs nanocomposite. This research illustrates the potential of nanostructured NDs-FG fibers as scaffolds for nerve repair and regeneration. We also emphasize the importance of further understanding the effect of the nanofiller-protein interphase on the microstructure and properties of electrospun fibers and on cell-interactivity.

Diamond-Coated Plasma Probes for Hot and Hazardous Plasmas.

Plasma probes are simple and inexpensive diagnostic tools for fast measurements of relevant plasma parameters. While in earlier times being employed mainly in relatively cold laboratory plasmas, plasma probes are now routinely used even in toroidal magnetic fusion experiments, albeit only in the edge region, i.e., the so-called scrape-off layer (SOL), where temperature and density of the plasma are lower. To further avoid overheating and other damages, in medium-size tokamak (MST) probes are inserted only momentarily by probe manipulators, with usually no more than a 0.1 s per insertion during an average MST discharge of a few seconds. However, in such hot and high-density plasmas, their usage is limited due to the strong particle fluxes onto the probes and their casing which can damage the probes by sputtering and heating and by possible chemical reactions between plasma particles and the probe material. In an attempt to make probes more resilient against these detrimental effects, we tested two graphite probe heads (i.e., probe casings with probes inserted) coated with a layer of electrically isolating ultra-nano-crystalline diamond (UNCD) in the edge plasma region of the Experimental Advanced Superconducting Tokamak (EAST) in Hefei, People's Republic of China. The probe heads, equipped with various graphite probe pins, were inserted frequently even into the deep SOL up to a distance of 15 mm inside the last closed flux surface (LCFS) in low- and high-confinement regimes (L-mode and H-mode). Here, we concentrate on results most relevant for the ability to protect the graphite probe casings by UNCD against harmful effects from the plasma. We found that the UNCD coating also prevented almost completely the sputtering of graphite from the probe casings and thereby the subsequent risk of re-deposition on the boron nitride isolations between probe pins and probe casings by a layer of conductive graphite. After numerous insertions into the SOL, first signs of detachment of the UNCD layer were noticed.

Biomimetic in vitro test system for evaluation of dental implant materials.

OBJECTIVES: Before application in dental practice, novel dental materials are tested in vitro and in vivo to ensure safety and functionality. However, transferability between preclinical and clinical results is often limited. To increase the predictive power of preclinical testing, a biomimetic in vitro test system that mimics the wound niche after implantation was developed. METHODS: First, predetermined implant materials were treated with human blood plasma, M2 macrophages and bone marrow stromal stem cells. Thereby, the three-dimensional wound niche was simulated. Samples were cultured for 28 days, and subsequently analyzed for metabolic activity and biomineralization. Second test level involved a cell-infiltrated bone substitute material for an osseointegration assay to measure mechanical bonding between dental material and bone. Standard and novel dental materials validated the developed test approach. RESULTS: The developed test system for dental implant materials allowed quantification of biomineralization on implant surface and assessment of the functional stability of mineralized biomaterial-tissue interface. Human blood plasma, M2 macrophages and bone marrow stromal stem cells proved to be crucial components for predictive assessment of implant materials in vitro. Biocompatibility was demonstrated for all tested materials, whereas the degree of deposited mineralized extracellular matrix and mechanical stability differed between the tested materials. Highest amount of functional biomineralization was determined to be on carbon-coated implant surface. SIGNIFICANCE: As an ethical alternative to animal testing, the established in vitro dental test system provides an economic and mid-throughput evaluation of novel dental implant materials or modifications thereof, by applying two successive readout levels: biomineralization and osseointegration.

Fabrication and Biocompatibility Evaluation of Nanodiamonds-Gelatin Electrospun Materials Designed for Prospective Tissue Regeneration Applications.

Due to the reduced ability of most harmed tissues to self-regenerate, new strategies are being developed in order to promote self-repair assisted or not by biomaterials, among these tissue engineering (TE). Human adipose-derived mesenchymal stem cells (hASCs) currently represent a promising tool for tissue reconstruction, due to their low immunogenicity, high differentiation potential to multiple cell types and easy harvesting. Gelatin is a natural biocompatible polymer used for regenerative applications, while nanodiamond particles (NDs) are used as reinforcing nanomaterial that might modulate cell behavior, namely cell adhesion, viability, and proliferation. The development of electrospun microfibers loaded with NDs is expected to allow nanomechanical sensing due to local modifications of both nanostructure and stiffness. Two aqueous suspensions with 0.5 and 1% w/v NDs in gelatin from cold water fish skin (FG) were used to generate electrospun meshes. Advanced morpho- and micro-structural characterization revealed homogeneous microfibers. Nanoindentation tests confirmed the reinforcing effect of NDs. Biocompatibility assays showed an increased viability and proliferation profile of hASCs in contact with FG_NDs, correlated with very low cytotoxic effects of the materials. Moreover, hASCs developed an elongated cytoskeleton, suggesting that NDs addition to FG materials encouraged cell adhesion. This study showed the FG_NDs fibrous scaffolds potential for advanced TE applications.

Pervasion of beta-tricalcium phosphate with nanodiamond particles yields efficient and safe bone replacement material amenable for biofunctionalization and application in large-size osseous defect healing.

Biofunctionalization of scaffold materials can enable the healing of large bone defects. In case of minimally invasive guided-bone regeneration (GBR), limitations are however hard-to-control side effects related to the potential release of biofactors into the systemic environment. Biofactors can be stably bound to nanodiamond particles (ND) through physisorption. We therefore tested the biological and clinical effects of refining beta-tricalcium phosphate (ßTCP) with ND in vitro and in vivo. In vitro, ßTCP carrying 4% ND resulted in enhanced attachment of mesenchymal stem cells. When assessing GBR after lateral augmentation of the mandible in sheep showed that ND in ßTCP resulted in a consistently steady bone formation when compared to pure ßTCP, demonstrating the biological inert behavior and the potential clinical safety of ND.

Impact of Nano-Crystalline Diamond Enhanced Hydrophilicity on Cell Proliferation on Machined and SLA Titanium Surfaces: An In-Vivo Study in Rodents.

By coating surfaces with nano-crystalline diamond (NCD) particles, hydrophilicity can be altered via sidechain modifications without affecting surface texture. The present study aimed to assess the impact of NCD hydrophilicity on machined and rough SLA titanium discs on soft tissue integration, using a rodent model simulating submerged healing. Four different titanium discs (machined titanium = M Titanium, NCD-coated hydrophilic machined titanium = M-O-NCD, sand blasted acid etched (SLA Titanium) titanium, and hydrophilic NCD-coated SLA titanium = SLA O-NCD) were inserted in subdermal pockets of 12 Wistar rats. After one and four weeks of healing, the animals were sacrificed. Biopsies were embedded in methyl methacrylate (MMA), and processed for histology. The number of cells located within a region of interest (ROI) of 10 µm around the discs were counted and compared statistically. Signs of inflammation were evaluated descriptively employing immunohistochemistry. At one week, M-O-NCD coated titanium discs showed significantly higher amounts of cells compared to M Titanium, SLA Titanium, and SLA-O-NCD (p < 0.001). At four weeks, significant higher cell counts were noted at SLA-O-NCD surfaces (p < 0.01). Immunohistochemistry revealed decreased inflammatory responses at hydrophilic surfaces. Within the limits of an animal study, M-O-NCD surfaces seem to stimulate cell proliferation in the initial healing phase, whereas SLA-O-NCD surfaces appeared advantageous afterwards.

A Copolymer Scaffold Functionalized with Nanodiamond Particles Enhances Osteogenic Metabolic Activity and Bone Regeneration.

Functionalizing polymer scaffolds with nanodiamond particles (nDPs) has pronounced effect on the surface properties, such as improved wettability, an increased active area and binding sites for cellular attachment and adhesion, and increased ability to immobilize biomolecules by physical adsorption. This study aims to evaluate the effect of poly(l-lactide-co-ε-caprolactone) (poly(LLA-co-CL)) scaffolds, functionalized with nDPs, on bone regeneration in a rat calvarial critical size defect. Poly(LLA-co-CL) scaffolds functionalized with nDPs are also compared with pristine scaffolds with reference to albumin adsorption and seeding efficiency of bone marrow stromal cells (BMSCs). Compared with pristine scaffolds, the experimental scaffolds exhibit a reduction in albumin adsorption and a significant increase in the seeding efficiency of BMSCs (p = 0.027). In the calvarial defects implanted with BMSC-seeded poly(LLA-co-CL)/nDPs scaffolds, live imaging at 12 weeks discloses a significant increase in osteogenic metabolic activity (p = 0.016). Microcomputed tomography, confirmed by histological data, reveals a substantial increase in bone volume (p = 0.021). The results show that compared with conventional poly(LLA-co-CL) scaffolds those functionalized with nDPs promote osteogenic metabolic activity and mineralization capacity. It is concluded that poly(LLA-co-CL) composite matrices functionalized with nDPs enhance osteoconductivity and therefore warrant further study as potential scaffolding material for bone tissue engineering.

Functionalization of bone implants with nanodiamond particles and angiopoietin-1 to improve vascularization and bone regeneration.

One of the major challenges in bone tissue engineering is adequate vascularization within bone substituents for nutrients and oxygen supply. In this study, the production and results of a new, highly functional bone construct consisting of a commercial three-dimensional ß-tricalcium phosphate scaffold (ß-TCP, ChronOS®) and hydrophilic, functionalized nanodiamond (ND) particles are reported. A 30-fold increase in the active surface area of the ChronOS + ND scaffold was achieved after modification with ND. In addition, immobilization of angiopoietin-1 (Ang-1) via physisorption within the ß-TCP + ND scaffold retained the bioactivity of the growth factor. Homogeneous distribution of the ND and Ang-1 within the core of the three-dimensional scaffold was confirmed using ND covalently labelled with Oregon Green. The biological responses of the ß-TCP + ND scaffold with and without Ang-1 were studied in a sheep calvaria critical size defect model showing that the ß-TCP + ND scaffold improved the blood vessel ingrowth and the ß-TCP + ND + ND + Ang-1 scaffold further promoted vascularization and new bone formation. The results demonstrate that the modification of scaffolds with tailored diamond nanoparticles is a valuable method for improving the characteristics of bone implants and enables new approaches in bone tissue engineering.

Nanodiamond modified copolymer scaffolds affects tumour progression of early neoplastic oral keratinocytes.

This study aimed to evaluate the tumorigenic potential of functionalising poly(LLA-co-CL) scaffolds. The copolymer scaffolds were functionalised with nanodiamonds (nDP) or with nDP and physisorbed BMP-2 (nDP-PHY) to enhance osteoinductivity. Culturing early neoplastic dysplastic keratinocytes (DOK(Luc)) on nDP modified scaffolds reduced significantly their subsequent sphere formation ability and decreased significantly the cells' proliferation in the supra-basal layers of in vitro 3D oral neoplastic mucosa (3D-OT) when compared to DOK(Luc) previously cultured on nDP-PHY scaffolds. Using an in vivo non-invasive environmentally-induced oral carcinogenesis model, nDP scaffolds were observed to reduce bioluminescence intensity of tumours formed by DOK(Luc) + carcinoma associated fibroblasts (CAF). nDP modification was also found to promote differentiation of DOK(Luc) both in vitro in 3D-OT and in vivo in xenografts formed by DOK(Luc) alone. The nDP-PHY scaffold had the highest number of invasive tumours formed by DOK(Luc) + CAF outside the scaffold area compared to the nDP and control scaffolds. In conclusion, in vitro and in vivo results presented here demonstrate that nDP modified copolymer scaffolds are able to decrease the tumorigenic potential of DOK(Luc), while confirming concerns for the therapeutic use of BMP-2 for reconstruction of bone defects in oral cancer patients due to its tumour promoting capabilities.

In Vivo Host Response and Degradation of Copolymer Scaffolds Functionalized with Nanodiamonds and Bone Morphogenetic Protein 2.

The aim is to evaluate the effect of modifying poly[(l-lactide)-co-(ε-caprolactone)] scaffolds (PLCL) with nanodiamonds (nDP) or with nDP+physisorbed BMP-2 (nDP+BMP-2) on in vivo host tissue response and degradation. The scaffolds are implanted subcutaneously in Balb/c mice and retrieved after 1, 8, and 27 weeks. Molecular weight analysis shows that modified scaffolds degrade faster than the unmodified. Gene analysis at week 1 shows highest expression of proinflammatory markers around nDP scaffolds; although the presence of inflammatory cells and foreign body giant cells is more prominent around the PLCL. Tissue regeneration markers are highly expressed in the nDP+BMP-2 scaffolds at week 8. A fibrous capsule is detectable by week 8, thinnest around nDP scaffolds and at week 27 thickest around PLCL scaffolds. mRNA levels of ALP, COL1α2, and ANGPT1 are significantly upregulating in the nDP+BMP-2 scaffolds at week 1 with ectopic bone seen at week 8. Even when almost 90% of the scaffold is degraded at week 27, nDP are observable at implantation areas without adverse effects. In conclusion, modifying PLCL scaffolds with nDP does not aggravate the host response and physisorbed BMP-2 delivery attenuates inflammation while lowering the dose of BMP-2 to a relatively safe and economical level.

Biofunctionalization of scaffold material with nano-scaled diamond particles physisorbed with angiogenic factors enhances vessel growth after implantation.

Biofunctionalized scaffold facilitates complete healing of large defects. Biological constraints are induction and ingrowth of vessels. Angiogenic growth factors such as vascular endothelial growth factor or angiopoietin-1 can be bound to nano-scaled diamond particles. Corresponding bioactivities need to be examined after biofunctionalization. We therefore determined the physisorptive capacity of distinctly manufactured, differently sized nDP and the corresponding activities of bound factors. The properties of biofunctionalized nDPs were investigated on cultivated human mesenchymal stem cells and on the developing chicken embryo chorio-allantoic membrane. Eventually porous bone substitution material was coated with nDP to generate an interface that allows biofactor physisorption. Angiopoietin-1 was applied shortly before scaffold implantation into an osseous defect in sheep calvaria. Biofunctionalized scaffolds exhibited significantly increased rates of angiogenesis already one month after implantation. Conclusively, nDP can be used to ease functionalization of synthetic biomaterials. FROM THE CLINICAL EDITOR: With the advances in nanotechnology, many nano-sized materials have been used in the biomedical field. This is also true for nano-diamond particles (nDP). In this article, the authors investigated the physical properties of functionalized nano-diamond particles in both in-vitro and in-vivo settings. The positive findings would help improve understanding of these nanomaterials in regenerative medicine.

Release and bioactivity of bone morphogenetic protein-2 are affected by scaffold binding techniques in vitro and in vivo.

A low dose of 1µg rhBMP-2 was immobilised by four different functionalising techniques on recently developed poly(l-lactide)-co-(ε-caprolactone) [(poly(LLA-co-CL)] scaffolds. It was either (i) physisorbed on unmodified scaffolds [PHY], (ii) physisorbed onto scaffolds modified with nanodiamond particles [nDP-PHY], (iii) covalently linked onto nDPs that were used to modify the scaffolds [nDP-COV] or (iv) encapsulated in microspheres distributed on the scaffolds [MICS]. Release kinetics of BMP-2 from the different scaffolds was quantified using targeted mass spectrometry for up to 70days. PHY scaffolds had an initial burst of release while MICS showed a gradual and sustained increase in release. In contrast, NDP-PHY and nDP-COV scaffolds showed no significant release, although nDP-PHY scaffolds maintained bioactivity of BMP-2. Human mesenchymal stem cells cultured in vitro showed upregulated BMP-2 and osteocalcin gene expression at both week 1 and week 3 in the MICS and nDP-PHY scaffold groups. These groups also demonstrated the highest BMP-2 extracellular protein levels as assessed by ELISA, and mineralization confirmed by Alizarin red. Cells grown on the PHY scaffolds in vitro expressed collagen type 1 alpha 2 early but the scaffold could not sustain rhBMP-2 release to express mineralization. After 4weeks post-implantation using a rat mandible critical-sized defect model, micro-CT and Masson trichrome results showed accelerated bone regeneration in the PHY, nDP-PHY and MICS groups. The results demonstrate that PHY scaffolds may not be desirable for clinical use, since similar osteogenic potential was not seen under both in vitro and in vivo conditions, in contrast to nDP-PHY and MICS groups, where continuous low doses of BMP-2 induced satisfactory bone regeneration in both conditions. The nDP-PHY scaffolds used here in critical-sized bone defects for the first time appear to have promise compared to growth factors adsorbed onto a polymer alone and the short distance effect prevents adverse systemic side effects.

Optical signatures of silicon-vacancy spins in diamond.

Colour centres in diamond have emerged as versatile tools for solid-state quantum technologies ranging from quantum information to metrology, where the nitrogen-vacancy centre is the most studied to date. Recently, this toolbox has expanded to include novel colour centres to realize more efficient spin-photon quantum interfaces. Of these, the silicon-vacancy centre stands out with highly desirable photonic properties. The challenge for utilizing this centre is to realize the hitherto elusive optical access to its electronic spin. Here we report spin-tagged resonance fluorescence from the negatively charged silicon-vacancy centre. Our measurements reveal a spin-state purity approaching unity in the excited state, highlighting the potential of the centre as an efficient spin-photon quantum interface.

Electronic structure of the silicon vacancy color center in diamond.

The negatively charged silicon vacancy (SiV) color center in diamond has recently proven its suitability for bright and stable single photon emission. However, its electronic structure so far has remained elusive. We here explore the electronic structure by exposing single SiV defects to a magnetic field where the Zeeman effect lifts the degeneracy of magnetic sublevels. The similar responses of single centers and a SiV ensemble in a low strain reference sample prove our ability to fabricate almost perfect single SiVs, revealing the true nature of the defect's electronic properties. We model the electronic states using a group-theoretical approach yielding a good agreement with the experimental observations. Furthermore, the model correctly predicts polarization measurements on single SiV centers and explains recently discovered spin selective excitation of SiV defects.

Biological effects of functionalizing copolymer scaffolds with nanodiamond particles.

Significant evidence has indicated that poly(L-lactide)-co-(ɛ-caprolactone) [(poly(LLA-co-CL)] scaffolds could be one of the suitable candidates for bone tissue engineering. Oxygen-terminated nanodiamond particles (n-DP) were combined with poly(LLA-co-CL) and revealed to be positive for cell growth. In this study, we evaluated the influence of poly(LLA-co-CL) scaffolds modified by n-DP on attachment, proliferation, differentiation of bone marrow stromal cells (BMSCs) in vitro, and on bone formation using a sheep calvarial defect model. BMSCs were seeded on either poly(LLA-co-CL)- or n-DP-coated scaffolds and incubated for 1 h. Scanning electron microscopy (SEM) and fluorescence microscopy were used in addition to protein and DNA measurements to evaluate cellular attachment on the scaffolds. To determine the effect of n-DP on proliferation of BMSCs, cell/scaffold constructs were harvested after 3 days and evaluated by Bicinchoninic Acid (BCA) protein assay and SEM. In addition, the osteogenic differentiation of cells grown for 2 weeks on the various scaffolds and in a dynamic culture condition was evaluated by real-time RT-PCR. Unmodified and modified scaffolds were implanted into the calvaria of six-year-old sheep. The expression of collagen type I (COL I) and bone morphogenetic protein-2 (BMP-2) after 4 weeks as well as the formation of new bone after 12 and 24 weeks were analyzed by immunohistochemistry and histology. Scaffolds modified with n-DP supported increased cell attachment and the mRNA expression of osteopontin (OPN), bone sialoprotein (BSP), and BMP-2 were significantly increased after 2 weeks of culture. The BMSCs had spread well on the various scaffolds investigated after 3 days in the study with no significant difference in cell proliferation. Furthermore, the in vivo data revealed more positive staining of COL I and BMP-2 in relation to the n-DP-coated scaffolds after 4 weeks and presented more bone formation after 12 and 24 weeks. n-DP modification significantly increased cell attachment and differentiation of BMSCs on poly(LLA-co-CL) scaffolds in vitro and enhanced bone formation in vivo.

BMP-2 immobilized on nanocrystalline diamond-coated titanium screws; demonstration of osteoinductive properties in irradiated bone.

BACKGROUND: Irradiation results in impaired bone healing. Thus, osteosynthesis procedures are afflicted with increased failure rates. To improve osseointegration bone morphogenetic protein-2 (BMP-2) immobilized on nanocrystalline diamond (NCD)-coated implant surfaces might be 1 solution. METHODS: By 4 weeks after irradiation of pig's mandible with a dose of 60 Gy a fracture was accomplished. Osteosynthesis was performed either with titanium osteosynthesis screws or NCD-coated screws with immobilized BMP-2. Nonirradiated animals served as control. After 1, 2, 4, and 8 weeks screws were evaluated histologically. Bone biopsies were gained to extract mesenchymal stem or precursor cells (MSCs). RESULTS: MSCs after irradiation demonstrated a behavior comparable to that of unirradiated cells. Consequently, immobilized BMP-2 resulted in an initial increased bone contact ratio (p = .014) but demonstrated no sustainable effect compared with osseointegration in nonirradiated bone (p = .08). CONCLUSION: Immobilized BMP-2 demonstrates an osteoinductive effect in irradiated bone. MSCs as effector cells possess protective mechanisms to overcome the destructive effect of irradiation.

In vivo investigation on connective tissue healing to polished surfaces with different surface wettability.

OBJECTIVES: Connective tissue in contact to transgingival/-dermal implants presents itself as tight scar formation. Although rough surfaces support the attachment they increase bacterial colonisation as well. In contrast to surface roughness, little is known about the influence of surface wettability on soft-tissue healing in vivo. We therefore investigated the influence of different surface wettabilities on connective tissue healing at polished implant surfaces in vivo. MATERIAL AND METHODS: Three polished experimental groups (titanium, titanium coated with hydrophobic nano-crystalline diamond (H-NCD) and titanium coated with hydrophilic nano-crystalline diamond (O-NCD) were inserted into the subcutaneous connective tissue of the abdominal wall of 24 rats. Animals were sacrificed after 1 and 4 weeks resulting in eight specimen per group per time point. Specimen were subjected to histological evaluation (van Giesson's staining) and immunohistochemistry staining for proliferating cell nuclear antigen (PCNA), fibronectin and tumour necrosis factor-alpha (TNF-α). RESULTS: Histological evaluation revealed dense scar formation at the titanium and H-NCD surfaces. In contrast, the connective tissue was loose at the O-NCD surface with a significantly higher number of cells after 4 weeks. O-NCD demonstrated a strong expression of PCNA and fibronectin but a weak expression of TNF-α. In contrast, the PCNA and fibronectin expression was low at the titanium and H-NCD, with a strong signal of TNF-α at the H-NCD surface. CONCLUSIONS: Hydrophilicity influences the connective tissue healing at polished implant surfaces in vivo positively. The attachment of connective tissue and the number of cells in contact to the surface were increased. Moreover, the inflammatory response is decreased at the hydrophilic surface.

HREELS investigation of the surfaces of nanocrystalline diamond films oxidized by different processes.

This article reports on the use of high-resolution electron energy loss spectroscopy (HREELS) for the investigation of as-grown (hydrogen-terminated) and oxidized nanocrystalline diamond films (NCD) using chemical, physical, and electrochemical approaches. The results indicate that the nature and number of oxygen-related chemical groups generated on the NCD surface depend strongly on the oxidation process. A high concentration of C-O functions has been obtained on the NCD surface oxidized by rf (radio frequency) oxygen plasma, whereas the highest C═O/C-O ratio has been achieved by electrochemical oxidation. The NCD surface oxidized by rf plasma was totally free of C═O groups. Traces of surface hydroxyl groups (C-OH) have been detected upon annealing in air or through UV/ozone oxidation.

The surface properties of nanocrystalline diamond and nanoparticulate diamond powder and their suitability as cell growth support surfaces.

Nanocrystalline diamond (NCD) films and nanoparticulate diamond powder (DP) are the two main representatives of diamond at the nanoscale. This study was designed to investigate the suitability of these biomaterials as cell growth supports and to determine surface characteristic properties best suited to cell attachment and proliferation. Surface topography, chemical termination and wetting properties of NCD- and DP-coated borosilicate glass substrates were correlated to attachment, proliferation and differentially regulated gene expression of human renal epithelial cells (HK-2 cell line) cultured on these surfaces. Hydrogen-terminated NCD (NCD-H) surfaces were shown to inhibit cell attachment, which indicates that the lack of functional polar groups prevents adherent cells from settling on a surface, whether nanostructured or not. In contrast to NCD-H, oxygen-terminated NCD (NCD-O) as well as DP surfaces demonstrated improved cell attachment, as compared to borosilicate glass, which is a commonly used material for cell growth supports. NCD-O not only revealed an increased cell attachment, but also a markedly increased proliferation rate. Finally, none of the investigated surface modifications appeared to cause adverse cellular reactions or markedly alter cellular phenotype.

The role of oxygen termination of nanocrystalline diamond on immobilisation of BMP-2 and subsequent bone formation.

Medical implants are increasingly often inserted into bone of frail patients, who are advanced in years. Due to age, severe trauma or pathology-related bone changes, osseous healing at the implant site is frequently limited. We were able to demonstrate that coating of endosseous implants with nanocrystalline diamond (NCD) allows stable functionalization by means of physisorption with BMP-2. Strong physisorption was shown to be directly related to the unique properties of NCD, and BMP-2 in its active form interacted strongly when NCD was oxygen-terminated. The binding of the protein was monitored under physiological conditions by single molecule force spectroscopy, and the respective adsorption energies were further substantiated by force-field-calculations. Implant surfaces refined in such a manner yielded enhanced osseointegration in vivo, when inserted into sheep calvaria. Our results further suggest that this technical advancement can be readily applied in clinical therapies with regard to bone healing, since primary human mesenchymal stromal cells strongly activated the expression of osteogenic markers when being cultivated on NCD physisorbed with physiological amounts of BMP-2.