Aggregation kinetics of colloidal particles measured by gas-phase differential mobility analysis.

We demonstrate the utility of electrospray gas-phase ion-mobility analysis as a new method to investigate nanoparticle flocculation, or aggregation. Au nanoparticle (Au-NP) solutions were sampled via electrospray (ES), followed by differential ion-mobility analysis (DMA) to determine the particle mobility distribution. Multimodal size distributions obtained with ES-DMA indicated the presence of single Au-NPs (monomer) as well as larger Au-NP clusters such as dimers, trimers, and tetramers under specific solution conditions. The fraction of each aggregate species as a function of time was quantitatively characterized, from which the degree of aggregation, aggregation rate, and stability ratio at different ionic strengths were determined. The latter enabled the extraction of a surface potential (or surface charge density) of 64 +/- 2 mV for 10 nm Au-NPs, which is in good agreement with values obtained from other methods, thus validating our approach. Our results show that ES-DMA is a valuable tool for quantitatively probing the early stages of colloidal aggregation or as a preparatory tool for the size election of aggregates.

Gas-phase ion-mobility characterization of SAM-functionalized Au nanoparticles.

We present results of a systematic examination of functionalized gold nanoparticles (Au-NPs) by electrospray-differential mobility analysis (ES-DMA). Commercially available, citrate-stabilized Au colloid solutions (10-60 nm) were sized using ES-DMA, from which changes in particle size of less than 0.3 nm were readily discerned. It was found that the formation of salt particles and the coating of Au-NPs by salt during the electrospray process can interfere with the mobility analysis, which required the development of sample preparation and data correction protocols to extract correct values for the Au-NP size. Formation of self-assembled monolayers (SAMs) of alkanethiol molecules on the Au-NP surface was detected from a change in particle mobility, which could be modeled to extract the surface packing density of SAMs. A gas-phase temperature-programmed desorption (TPD) kinetic study of SAMs on Au-NPs found the data to be consistent with a second-order Arrhenius-based rate law, yielding an Arrhenius factor of 1.0 x 10 (11) s (-1) and an activation energy approximately 105 kJ/mol. For the size range of SAM-modified Au-NP we considered, the effect of surface curvature on the energetics of binding of carboxylic acid terminated SAMs is evidently negligible, with binding energies determined by TPD agreeing with those reported for the same SAMs on planar surfaces. This study suggests that the ES-DMA can be added to the tool set of characterization methods used to study the structure and properties of coated nanoparticles.

Surface characterization of laser-ablated polymers used for microfluidics.

Fabrication of microfluidic devices by excimer laser ablation under different atmospheres may provide variations in polymer microchannel surface characteristics. The surface chemistry and electroosmotic (EO) mobility of polymer microchannels laser ablated under different atmospheres were studied by X-ray photoelectron spectroscopy and current monitoring mobility measurements, respectively. The ablated surfaces of PMMA were very similar to the native material, regardless of ablation atmospheres due to the negligible absorption of 248-nm light by that polymer. The substrates studied that exhibit nonnegligible absorption at this energy, namely, poly(ethylene terephthalate glycol), poly(vinyl chloride), and poly(carbonate), showed significant changes in surface chemistry and EO mobility when the ablation atmospheres were varied. Ablation of these three polymer substrates under nitrogen or argon resulted in low EO mobilities with a loss of the well-defined chemical structures of the native surfaces, while ablation under oxygen yielded surfaces that retained native chemical structures and supported higher EO mobilities.

Detection of viable Cryptosporidium parvum using DNA-modified liposomes in a microfluidic chip.

This paper describes a microfluidic chip that enables the detection of viable Cryptosporidium parvum by detecting RNA amplified by nucleic-acid-sequence-based amplification (NASBA). The mRNA serving as the template for NASBA is produced by viable C. parvum as a response to heat shock. The chip utilizes sandwich hybridization by hybridizing the NASBA-generated amplicon between capture probes and reporter probes in a microfluidic channel. The reporter probes are tagged with carboxyfluorescein-filled liposomes. These liposomes, which generate fluorescence intensities not obtainable from single fluorophores, allow the detection of very low concentrations of targets. The limit of detection of the chip is 5 fmol of amplicon in 12.5 microL of sample solution. Samples of C. parvum that underwent heat shock, extraction, and amplification by NASBA were successfully detected and clearly distinguishable from controls. This was accomplished without having to separate the amplified RNA from the NASBA mixture. The microfluidic chip can easily be modified to detect other pathogens. We envision its use in mu-total analysis systems (mu-TAS) and in DNA-array chips utilized for environmental monitoring of pathogens.

Immobilization of nucleic acids at solid surfaces: effect of oligonucleotide length on layer assembly.

This report investigates the effect of DNA length and the presence of an anchoring group on the assembly of presynthesized oligonucleotides at a gold surface. The work seeks to advance fundamental insight into issues that impact the structure and behavior of surface-immobilized DNA layers, as in, for instance, DNA microarray and biosensor devices. The present study contrasts immobilization of single-stranded DNA (ssDNA) containing a terminal, 5' hexanethiol anchoring group with that of unfunctionalized oligonucleotides for lengths from 8 to 48 bases. Qualitatively, the results indicate that the thiol anchoring group strongly enhances oligonucleotide immobilization, but that the enhancement is reduced for longer strand lengths. Interestingly, examination of the probe coverage as a function of strand length suggests that adsorbed thiol-ssDNA oligonucleotides shorter than 24 bases tend to organize in end-tethered, highly extended configurations for which the long-term surface coverage is largely independent of oligonucleotide length. For strands longer than 24 bases, the surface coverage begins to decrease notably with probe length. The decrease is consistent with a less ordered arrangement of the DNA chains, presumably reflecting increasingly polymeric behavior.

Control of flow direction in microfluidic devices with polyelectrolyte multilayers.

Electroosmotic flow (EOF) is commonly utilized in microfluidics. Because the direction of the EOF can be determined by the substrate surface charge, control of the surface chemical state offers the potential, in addition to voltage control, to direct the flow in microfluidic devices. We report the use of polyelectrolyte multilayers (PEMs) to alter the surface charge and control the direction of flow in polystyrene and acrylic microfluidic devices. Relatively complex flow patterns with simple arrangements of applied voltages are realized by derivatization of different arms of a single device with oppositely charged polyelectrolytes. In addition, flow in opposite directions in the same channel is possible. A positively derivatized plastic substrate with a negatively charged lid was used to achieve top-bottom opposite flows. Derivatization of the two sides of a plastic microchannel with oppositely charged polyelectrolytes was used to achieve side-by-side opposite flows. The flow is characterized using fluorescence imaging and particle velocimetry.

Electrostatic interactions of redox cations with surface-immobilized and solution DNA.

Association constants for ruthenium(III) hexaamine and cobalt(III) tris(2,2'-bipyridine) with solution and surface-immobilized DNA were determined. The interaction of the cationic redox molecules with calf thymus DNA was monitored via normal pulse voltammetry with analysis of the mass-transfer limited current assuming a discrete binding-site model. Single-stranded DNA was immobilized on gold via self-assembly of a 5' hexanethiol linker. Double-stranded surface-immobilized DNA was produced by hybridization of a complementary target to surface-immobilized single strands. The interaction between the metal complexes and surface-immobilized DNA was determined using chronocoulometry to construct adsorption isotherms. The measured binding constants for the cationic redox molecules with solution, surface-immobilized single-stranded, and double-stranded DNA are well-correlated, even as a function of ionic strength. The agreement between the determined association constants for the surface-immobilized and solution DNA indicates the potential utility of DNA-derivatized electrodes for examination of small molecule interactions with nucleic acids.

Electrochemical quantitation of DNA immobilized on gold.

We have developed an electrochemical method to quantify the surface density of DNA immobilized on gold. The surface density of DNA, more specifically the number of nucleotide phosphate residues, is calculated from the amount of cationic redox marker measured at the electrode surface. DNA was immobilized on gold by forming mixed monolayers of thiol-derivitized, single-stranded oligonucleotide and 6-mercapto-1-hexanol. The saturated amount of charge-compensation redox marker in the DNA monolayer, determined using chronocoulometry, is directly proportional to the number of phosphate residues and thereby the surface density of DNA. This method permits quantitative determination of both single- and double-stranded DNA at electrodes. Surface densities of single-stranded DNA were precisely varied in the range of (1-10) x 10(12) molecules/cm2, as determined by the electrochemical method, using mixed monolayers. We measured the hybridization efficiency of immobilized single-stranded DNA to complementary strands as a function of the immobilized DNA surface density and found that it exhibits a maximum with increasing surface density.

Supramolecular architectures for the functionalization of solid surfaces.

Surface plasmon optical techniques are described as sensitive tools that allow for the on-line characterization of supramolecular biofunctional architectures at solid/solution interfaces. After a short introduction into the fundamentals of surface plasmon optics the observation of the build up of a functional bio-interface by the self-assembly process of long chain thiolates at an Au surface is described. Criteria are developed for tailoring the SAM architectures optimized for maximum protein binding from solution by specific bio-recognition reactions. SPM is employed to image the selective binding of streptavidin to a functionalized SAM laterally patterned by UV-photolithographic techniques.