RESUMO
The demand for novel and renewable sources of energy has increased as a result of rapid population growth, limited sources of bioenergy, and environmental pollution, caused by excessive use of fossil fuels. The need to meet future energy demands have motivated researchers to search for alternative and sustainable sources of energy. The bioconversion of lignocellulosic waste (agricultural and food waste) into biofuels shows competitive promises. Lignocellulosic waste is easily accessible and has a large enzyme system that can be immobilised onto nano-matrices. Consequently, resulting in higher biofuel production and process efficiency. However, the excessive production cost of the current procedures, which involve physical, chemical, and enzymatic reactions, is limited. The use of nanomaterials has recently been shown to concentrate lignocellulosic waste, therefore, reviewing the quest for efficient production of sustainable and cost-effective development of bioenergy from lignocellulosic wastes. This review paper explores the advanced strategies of using nanobiotechnology to combine enzyme-conjugated nanosystems for the cost-effective production of sustainable bioenergy solutions. This research will help to develop an inexpensive, eco-friendly technology for biofuels production and also help overcome the environmental burden of lignocellulosic waste worldwide.
RESUMO
Characteristics and performance of a time of flight (TOF) spectrometer developed for performing fission mass distribution studies are presented. The spectrometer contains two TOF arms based on multi-wire proportional counters (MWPCs). Each arm has two MWPCs to form a start-stop detection system for TOF measurements. The start detector has an active area of 4 × 4 cm2. The stop detector is a two-dimensional position sensitive MWPC with an active area of 16 × 11 cm2. Salient features of the MWPCs are the use of reduced sub-millimeter wire pitches of 0.635 and 0.317 mm in the electrodes along with the use of gold plated tungsten wires of diameters 10 and 20 µm. A delay line for position electrodes is prepared using chip inductors and capacitors. Ten different configurations of MWPC were investigated for the start detector, which involved the use of three and four electrode geometries, use of different wire pitches, and use of aluminized mylar for timing electrodes. Performance results close to micro-channel plate detectors have been observed with some designs of MWPC, displaying rise times better than 2 ns with an estimated inherent time resolution of â¼100 ps FWHM. A position resolution of â¼1 mm (FWHM) has been observed. Design features of the MWPCs and their test performance results are described in this article.
RESUMO
Metagenomics and directed evolution technology have brought a revolution in search of novel enzymes from extreme environment and improvement of existing enzymes and tuning them towards certain desired properties. Using advanced tools of molecular biology i.e. next generation sequencing, site directed mutagenesis, fusion protein, surface display, etc. now researchers can engineer enzymes for improved activity, stability, and substrate specificity to meet the industrial demand. Although many enzymatic processes have been developed up to industrial scale, still there is a need to overcome limitations of maintaining activity during the catalytic process. In this article recent developments in enzymes industrial applications and advancements in metabolic engineering approaches to improve enzymes efficacy and production are reviewed.
Assuntos
Evolução Molecular Direcionada , Indústrias , Catálise , Enzimas/genética , Enzimas/metabolismo , Biologia Molecular , Engenharia de Proteínas , Especificidade por SubstratoRESUMO
Wide sustainability and reusability of biomacromolecules such as carbohydrates and proteins-based biopolymers pave the way for providing maximal importance in the field of generating biopolymeric nanoparticles. As compared to synthetic nanomaterials, carbohydrate and protein based biopolymeric nanomaterials offer unique advantages that include antibacterial, biocompatible, immunogenicity, and biodegradable properties. Additionally, they have the significant property of more size distribution. Carbohydrate nanoparticles are primarily derived from the polysaccharide biopolymers such as alginate and chitosan; and protein nanoparticles are made from the diverse peptide biopolymers such as albumin, keratin, sericin, fibroin, gelatin and collagen. Advanced methods such as emulsification, desolvation, electrohydrodynamic atomization and coacervation are employed for the controlled fabrication of green biomacromolecules based nanoparticles. Suitability of biopolymeric nanoparticles in plethora of biotechnological applications are quite feasible with the advent of advanced technologies such as dynamic light scattering, scanning electron microscopy, transmission electron microscopy, atomic force microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and UV visible spectroscopy etc. Applications of such biomacromolecules nanoparticles are highly prevalent in agriculture, food, and biomedical industries. Thus, contributions of biopolymeric nanoparticles derived from carbohydrates and proteins biomacromolecules and their recent trends of patents granted in the biotechnological applications are critically discussed along with a promising future scope.
Assuntos
Biopolímeros , Carboidratos/química , Nanopartículas , Proteínas/química , NanotecnologiaRESUMO
Thin carbon-backed isotopically enriched 208Pb targets were required for our experiment aimed to study the reaction dynamics for 48Ti + 208Pb system, populating the near super-heavy nucleus 256Rf, through mass-energy correlation of the fission fragments. Purity and thickness of the targets are of utmost importance in such studies as these factors have strong influence on the measurement accuracy of mass and energy distribution of fission fragments. 208Pb targets with thickness ranging from 60 µg/cm2 to 250 µg/cm2 have been fabricated in high vacuum environment using physical vapor deposition method. Important points in the method are as follows: â¢208Pb was deposited using resistive heating method, whereas carbon (backing foil) deposition was performed by using the electron beam bombardment technique.â¢Different characterization techniques such as Particle Induced X-ray Emission (PIXE), Energy Dispersive X-Ray Fluorescence (EDXRF) and Rutherford Backscattering Spectrometry (RBS) were used to assert the purity and thickness of the targets.â¢These targets have successfully been used to accomplish our experimental objectives.
RESUMO
The cheese whey, a by-product of dairy industry proved to be an attractive substrate for production of ß-carotene. The ß-carotene production from Mucor azygosporus MTCC 414 by using deproteinized waste whey filtrate under submerged fermentation was investigated. Various fermentation variables, such as lactose content in whey, initial pH, production temperature, incubation time, and carbon and nitrogen sources played significant role on ß-carotene production. Maximum ß-carotene production (385 µg/g dcw) was obtained with the whey (pH 5.5) containing 3.5% (w/v) lactose supplemented with soluble starch at (1.0%, w/v) at 30°C after a 5 days incubation. Moreover, unlike other microorganisms which utilize pre-hydrolyzed lactose, this Mucor azygosporus MTCC 414 was found to be capable of utilizing unhydrolyzed lactose present in the whey.