Job function as determinant of clinker exposure at workplaces during cement production.

OBJECTIVES: In the cement production industry, exposure to airborne particulate matter is associated with a decline in lung function and increased airway symptoms. Exposure to clinker-the major constituent of cement and supposedly the cause of the observed adverse health effects-was determined recently in 15 cement production plants located in 8 different countries (Estonia, Greece, Italy, Norway, Sweden, Switzerland, Spain, Turkey). It was shown that the median clinker abundance in the thoracic fraction varied between approximately 20% and 70% for individual plants. The present study complements the previous work by investigating the significance of job function as a determinant of clinker exposure. METHODS: The elemental composition (water and acid-soluble fractions separately) of 1,227 personal thoracic workplace samples was analyzed by positive matrix factorization (PMF) to determine the contribution of different sources to the composition of airborne particulate matter and to quantify the clinker content. RESULTS: Median thoracic mass air concentrations varied for individual job functions between 0.094 and 12 mg/m3 (estimated separately for different plants). The PMF 5-factor solution yielded median relative clinker abundances in the personal thoracic samples between 7.6% and 81% for individual job functions. Thoracic clinker air concentrations are highest for cleaning, production, and maintenance work, and lowest for administration and other work. Foremen and laboratory personnel show intermediate exposure levels. The plant was found to have a much higher contribution to the total variance of the thoracic clinker air concentrations than the job function. Thoracic clinker air concentrations (medians between 0.01 and 5.5 mg/m3) are strongly correlated with the thoracic mass air concentrations and to a lesser extent with the relative clinker abundance in an aerosol sample. CONCLUSIONS: Job function is an important predictor of exposure to clinker in the cement production industry. As clinker is suspected to be the causal agent for the observed adverse health effects among cement production workers, the clinker air concentration may be a better exposure metric than thoracic air mass concentration despite the strong correlation between the two. Reduction strategies should focus on the most exposed job categories cleaning, production, and maintenance work.

Chemical Composition of Thoracic Dust at Workplaces During Cement Production.

OBJECTIVES: Cement belongs to the most used building materials. Clinker is the major constituent of cement, and it is believed that the strong increase of pH after hydration of clinker minerals is responsible for the observed decline in lung function of cement production workers. Information on clinker exposure at workplaces in the cement production industry is scarse. The aims of this study are to determine the chemical composition of thoracic dust and to quantify workplace exposure to clinker in cement production. METHODS: The elemental composition of 1250 personal thoracic samples collected at workplaces in 15 plants located in 8 different countries (Estonia, Greece, Italy, Norway, Sweden, Switzerland, Spain, Turkey) was determined by inductively coupled plasma optical emission spectrometry (ICP-OES), separately for water- and acid-soluble fraction. Positive matrix factorization (PMF) was used to determine the contribution of different sources to the dust composition and to quantify the clinker content in 1227 of the thoracic samples. In addition, 107 material samples were analysed to facilitate interpretation of the factors obtained by PMF. RESULTS: The median thoracic mass concentrations varied for individual plants between 0.28 and 3.5 mg/m3. PMF with 8 water-soluble and 10 insoluble (i.e., acid-soluble) element concentrations yielded a five-factor solution: Ca, K, Na sulfates; silicates; insoluble clinker; soluble clinker-rich; and soluble Ca-rich. The clinker content of the samples was calculated as sum of the insoluble clinker and soluble clinker-rich factors. The median clinker fraction of all samples was 45% (range 0-95%), and varied between 20% and 70% for individual plants. DISCUSSION: The 5-factor solution of PMF was selected on the basis of several mathematical parameters recommended in the literature as well as the mineralogical interpretability of the factors. In addition, interpretation of the factors was supported by the measured apparent solubility of Al, K, Si, Fe, and to a lesser extent Ca in material samples. The total clinker content obtained in the present study is considerably lower than estimates based on the Ca concentrations in a sample, and somewhat lower than estimates based on Si concentrations after selective leaching with a methanol/maleic acid mixture. The clinker abundance in workplace dust of one plant investigated in the present contribution was also estimated in a recent study by electron microscopy, and the good agreement between both studies gives confidence in the results of PMF. CONCLUSIONS: The clinker fraction in personal thoracic samples could be quantified from the chemical composition by positive matrix factorization. Our results allow for further epidemiological analyses of health effects in the cement production industry. As these estimates are more accurate for clinker exposure than aerosol mass, stronger associations with respiratory effects are expected if clinker is the main cause of these effects.

Diet and Blood Concentrations of Essential and Non-Essential Elements among Rural Residents in Arctic Russia.

Nutrition is an essential factor for human health. Earlier research has suggested that Arctic residents are vulnerable to environmental toxic exposures through traditional foods. Although Russia is the largest Arctic country, the evidence on the topic from the Russian part of the Arctic is scarce. We studied associations between blood concentrations of essential and non-essential elements and traditional food consumption in 297 adults from seven rural settlements in the Nenets Autonomous Area, Northwest Russia. Blood arsenic concentration was positively associated with consumption of rainbow smelt, pink salmon, Arctic char and navaga fish. Frequent consumption of northern pike was associated with increased concentration of blood mercury. Blood mercury and arsenic concentrations were significantly associated with blood selenium. We also observed positive associations between blood lead levels and the frequency of goose consumption. Moreover, subjects who reported to be hunters had higher blood levels of lead, suggesting contamination of goose meat with fragments of shotgun shells. Blood cobalt and manganese concentrations were inversely associated with serum ferritin levels. Positive associations between blood levels of manganese and lead were observed. Moreover, blood lead concentrations were significantly associated with cadmium, mercury, copper, and zinc. Our results corroborate earlier findings on the traditional foods as source of non-essential elements for the Arctic residents. Observed correlations between the levels of lead and other elements warrant further research and may have potential implications for the studies on the associations between essential elements and health outcomes.

Occupational Exposure among Electronic Repair Workers in Ghana.

Electronic repair workers may be exposed to lead, mercury, cadmium and other elements including rare earth elements used in electronic equipment. In this study, repair work took place in small repair shops where, e.g., televisions, radios, video players, compact discs and computers were repaired. Personal full-shift air samples of particulate matter were collected among 64 electronic repair workers in Kumasi (Ghana) and analysed for 29 elements by inductively coupled plasma mass spectrometry. Results showed that air concentrations of all elements were low. The highest air concentration was measured for iron with a geometric mean concentration and geometric standard deviation of 6.3 ± 0.001 µg/m3. The corresponding concentration of Pb and Hg were 157 ± 3 ng/m3 and 0.2 ± 2.7 ng/m3, respectively. The cerium concentration of 5 ± 2 ng/m3 was the highest among the rare earth elements. Source apportionment with ranked principal component analysis indicated that 63% of the variance could be explained by the repair and soldering of electronic components such as batteries, magnets, displays and printed circuit boards. An association between concentrations of lead in the workroom air and lead in whole blood was found (Pearson's correlation coefficient r = 0.42, p < 0.001). There was, however, no statistically significant difference between whole blood lead concentrations in the workers and references indicating that lead did not exclusively originate from occupational exposure.

Physicochemical characterization of particulate matter in a cement production plant.

Employees working in cement production plants are exposed to airborne particulate matter (PM) which may lead to lung function impairments and airway symptoms. The PM consists of raw materials, clinker and additives which vary depending on cement blend. The aim of this work was to characterize the thoracic fraction of PM with regard to size, phase composition and mixing state. Both stationary and personal impactors were used to collect size-fractionated samples in a cement production plant in Norway. Stationary samples were measured with aerosol particle counters and collected with a 13-stage cascade impactor, which were stationed at three locations of the cement production plant: at the raw meal mill, clinker conveyor belt and cement mill. Sioutas cascade impactors, and thoracic and respirable dust samplers were used in parallel for personal sampling. Additionally, particles for electron microscopy were collected with the stationary cascade impactor for size-fractionated single particle characterization. Gravimetric measurements and element compositions of the samples from the stationary impactors show that the PM mass is dominated by calcium-rich particles of size >1 µm. The size distribution results of stationary and personal impactors were similar. Characterization of single particles reveals that limestone is the dominating material in the raw meal mill, whereas clinker and limestone dominate at the clinker conveyor belt and at the cement mill. The element composition of clinker PM did not change with particle size. The PM collected on impactor stages with aerodynamic diameter cut-offs below 0.56 µm was dominated by soot and volatile secondary particles at the three locations. The number of ultrafine particles of the cement related compounds was low. Air concentrations of PM in personal respirable and thoracic samples ranged from 0.14-10 mg m-3 to 0.37-9.5 mg m-3, respectively. Considerable local variations exist, both in composition and air concentration of the PM.

Geographic and Ethnic Variations in Serum Concentrations of Legacy Persistent Organic Pollutants among Men in the Nenets Autonomous Okrug, Arctic Russia.

The overwhelming majority of Arctic biomonitoring studies in humans include either pregnant or non-pregnant women of reproductive age while little attention is paid to toxic compounds concentrations in men. This study contributes with information of the present amounts of persistent organic pollutants (POPs) in men living in Arctic Russia. We studied the serum concentrations of 11 polychlorinated biphenyl (PCB) congeners and 17 organochlorine pesticides (OCPs) and some of their metabolites in samples collected from 92 adult men (mean age 43 years) from seven different settlements in Nenets Autonomous Okrug (NAO). The median concentrations of individual PCB congeners increased in the order PCB 183, PCB 180, PCB 118, PCB 138, PCB 153. The concentrations of o, p'-DDD, p, p'-DDD, aldrin, mirex and 1,2,3,5-TCB were in most cases below the quantification limit. The observed concentrations of PCBs and chlorinated pesticides were in the same range as those found in similar groups of women of these territories, but lower than of men in other Arctic countries. However, significant geographic differences between the settlements were observed with exceptionally high concentrations of PCBs in the Islands group. The highest serum ∑PCBs and ß-HCH levels were observed in adult males aged 60-78 years. We found significant variations in serum concentrations of POPs across settlements and ethnic groups with exceptionally high concentrations of PCBs among the residents of the Arctic islands. At the same time, our findings suggest a considerable decrease in serum concentration of POPs over the last decade.

Particle characterisation and bioaccessibility of manganese in particulate matter in silico- and ferromanganese smelters.

The aim of this study was to characterise particulate matter (PM) collected in the furnace area during SiMn and high carbon (HC)-FeMn production in terms of single particle analysis and to determine the bioaccessibility of Mn in the PM in a simulated lung fluid. Airborne PM was collected with Sioutas cascade impactors and respirable cyclones in the breathing zone of tappers and crane operators. Stationary samples were collected from the furnace area with a nanoMOUDI cascade impactor and an ESPnano electrostatic particle collector. Individual particles were characterised by scanning and transmission electron microscopy. Bioaccessibility of Mn was studied in terms of the dissolution of Mn in Gamble solution (24 hours leaching at 37 °C) relative to total Mn. Slag particles, alloy fragments, Mn and Fe oxides as well as carbonaceous particles were observed in the size fraction > 1 µm aerodynamic diameter (dae). Thermally generated condensation particles dominated the dae size range of 0.18-1 µm collected from the tapping fumes, while carbonaceous particles dominated the fraction below 0.18 µm. Condensation generated particles from the furnace area of HC-FeMn production were coated with an amorphous Si-O rich surface layer which seemed to hold primary particles together as aggregates. In the same size range, the particles from the furnace area of SiMn production were dominated by spherical condensation particles rich in Si, Mn and O, but without a Si-O rich surface layer. Instead, the Mn oxides were enclosed in an amorphous Si-O rich matrix. The bioaccessibility of Mn was low to moderate (<30%), but higher for SiMn furnace workers (highest median = 23%) than HC-FeMn furnace workers (highest median = 12%). This difference in bioaccessibility was significant for PM with dae up to 2.5 µm, and most pronounced in the dae size range between 0.25 and 1.0 µm. Also, a significantly higher bioaccessibility of Mn was found for PM larger than dae of 0.5 µm collected among crane operators compared to tappers in the HC-FeMn smelter.

Essential and non-essential elements in biological samples of inhabitants residing in Nenets Autonomous Okrug of the Russian Arctic.

Exposure of Arctic residents to environmental pollutants is an emerging public health problem receiving little global attention. The objective of this study was to assess whole blood concentrations of nine selected essential (Co, Cu, Mn, Se, Zn) and non-essential (As, Cd, Hg, Pb) elements among Nenets and non-Nenets adult residents of the Nenets Autonomous Okrug (NAO) living in seven coastal and inland settlements. Urine was collected in two settlements for assessment of iodine status. Altogether 297 whole blood and 68 urine samples were analysed by inductively coupled mass spectrometry and the accuracy of the measurements was assessed by use of human whole blood and urine quality control materials. Several essential and non-essential showed significant variations in whole blood concentrations characterized by gender, population group and locality. Cd levels among non-Nenets non-smokers (0.19 µg/L) indicated a dietary intake at a natural global background level. Hg concentrations in whole blood show that not more than 10% of women in the fertile age had a Hg intake above the EFAS's recommendation. The Pb concentrations were in the range of, or partly exceeding reference values for increased risk of nephrotoxicity, and there is a need for a continued effort to reduce Pb exposure among the population groups in NAO. With high prevalence of obesity among the Nenets and non-Nenets population, a high prevalence of Fe-deficiency among menstruating women (<50 years) (37.2%) and a lower I status than recommended by WHO, these nutritional dependent components deserve further attention.

Per- and Polyfluoroalkyl Substances in Human Serum Samples of Selected Populations from Ghana.

The aims of this study were to assess serum concentrations of per- and polyfluoroalkyl substances (PFASs) in selected populations from Ghana, including workers engaged in the repair of electronic equipment (ERWs), and to elucidate PFAS concentrations in relation to blood mercury concentrations (B-Hg) as a biomarker of seafood consumption. In all, 219 participants were recruited into the study, of which 26 were women and 64 were ERWs. Overall, the PFAS concentrations were low. The most abundant components were perfluorooctane sulfonate (PFOS) and perfluorohexane sulfonic acid (PFHxS). Women had generally lower PFAS concentration than men. The ERWs had statistically significantly higher concentrations of perfluorooctanoate (PFOA), which was associated with the concentration of tin in urine. This could indicate exposure during soldering. The concentration of B-Hg was associated with several of the PFASs such as PFOA, PFOS and perfluoroheptane sulfonate (PFHpS). Additionally, the concentrations of perfluorodecanoic acid (PFDA) and perfluoroundecanoate (PFUnDA) were highly associated with the concentrations of B-Hg. It is noteworthy that the linear isomer of PFHxS was strongly associated with B-Hg while the branched isomers of PFHxS were not. In conclusion, the PFAS concentrations observed in the present study are low compared to other populations previously investigated, which also reflects a lower PFAS exposure within the Ghanaian cohorts. ERWs had significantly higher PFOA concentrations than the other participants. Several PFASs were associated with B-Hg, indicating that seafood consumption may be a source of PFAS exposure.

Concentrations of Persistent Organic Pollutants in Women's Serum in the European Arctic Russia.

Persistent organic pollutants (POPs) are heterogeneous carbon-based compounds that can seriously affect human health. The aim of this study was to measure serum concentrations of POPs in women residing in the Euro-Arctic Region of Russia. A total of 204 women from seven rural settlements of the Nenets Autonomous Okrug (NAO) took part in the study. We measured serum concentrations of 11 polychlorinated biphenyls (PCBs) and 17 organochlorine pesticides (OCPs) across the study sites and among Nenets and non-Nenets residents. Measurement of POPs was performed using an Agilent 7890A gas chromatograph equipped with an Agilent 7000 series MS/MS triple quadrupole system. The concentrations of all POPs were low and similar to findings from other Arctic countries. However, significant geographic differences between the settlements were observed with exceptionally high concentrations of PCBs in Varnek located on Vaygach Island. Both ΣDDT (p = 0.011) and ΣPCB (p = 0.038) concentrations were significantly lower in Nenets. Our main findings suggest that the serum concentrations of the legacy POPs in women in the Euro-Arctic Region of Russia are low and similar to those in other Arctic countries. Significant variations between settlements, and between Nenets and non-Nenets residents, were found. Arctic biomonitoring research in Russia should include studies on the associations between nutrition and concentrations of POPs.

Characterization of ultrafine particles emitted during laser-based additive manufacturing of metal parts.

Particulate matter (PM) emitted during laser additive manufacturing with stainless steel powder materials has been studied in detail. Three different additive manufacturing techniques were studied: selective laser melting, direct metal deposition and laser cladding. Gas flow and temperature fields accompanying the processes were numerically modeled for understanding particle growth and oxidation. Transmission and scanning electron microscopy were used for primary particle and PM characterization. The PM collected in the atmosphere during manufacturing consisted of complex aggregates/agglomerates with fractal-like geometries. The overwhelming number of particles formed in the three processes had equivalent projected area diameters within the 4-16 nm size range, with median sizes of 8.0, 9.4 and 11.2 nm. The primary particles were spherical in shape and consisted of oxides of the main steel alloying elements. Larger primary particles (> 30 nm) were not fully oxidized, but where characterized by a metallic core and an oxidic surface shell.

Iodine Status of Women and Infants in Russia: A Systematic Review.

This systematic review presents a critical synthesis of the available information on the iodine status among women and infants in Russia. Literature search was performed in accordance with PRISMA guidelines using PubMed, Scopus Web of Science databases as well as eLIBRARY-the Russian national source. Altogether, 277 papers were identified and 19 of them were eligible for the review. The data on median urinary iodine concentration (UIC) in women and infants from 25 Russian regions were presented. A substantial variability in UIC across the country with no clear geographical pattern was observed. Despite substantial heterogeneity in research methodology and data presentation the results suggest that the iodine status among pregnant women and infants in Russia is below the recommended levels. Our findings demonstrate that iodine deficiency is a re-emerging public health problem in Russia. Urgent public health measures on national, regional and individual levels are warranted.

Occupational Medicine and Environmental Health in the Border Areas of Euro-Arctic Barents Region: A Review of 30-Year Russian-Norwegian Research Collaboration Outcomes.

This year marks 30 years of close collaboration between a consortium of institutions, namely, the Northwest Public Health Research Center, Saint-Petersburg (NWPHRC); the Institute of Community Medicine (ICM) of UiT (The Arctic University of Norway, Tromsø); the National Institute of Occupational Health (NIOH), Oslo; the University Hospital of Northern Norway (UNN) at Tromsø; and McMaster University (MU), Hamilton, ON, Canada. During the early years of cooperation, Dr. Chashchin was the Director of the Scientific Laboratory of the North-West Public Health Centre Branch of the NWPHRC located in the town of Kirovks in the Murmansk Region. The primary focus of this long-standing collaboration was to assess and address issues that are important for maintaining the health of the population living in the border areas of Russia and Norway and included the reduction of occupational health risks among workers employed in mining, metallurgical and machine-building enterprises located in the north-western region of Norway and the adjoining Kola Peninsula in Russia. These industrial activities constituted essential components of the local industries. The ongoing Russian-Norwegian cooperation in the field of occupational medicine is an excellent example of the effective combination of intellectual potential and research technologies of multiple countries. It has resulted in the development of a scientifically based set of measures for practical implementation, contributing to the improvement of working conditions and preservation of the health of workers employed at enterprises where the joint research was carried out.

Iodine and bromine in fish consumed by indigenous peoples of the Russian Arctic.

Fish muscle may constitute one of the main sources of iodine (I) for the indigenous peoples of the Russian Arctic, although limited information is available about its content in commonly consumed fish species. In the current study, bromine (Br), I, the essential elements (copper, selenium and zinc) and other non-essential elements - specifically mercury, arsenic (As), cadmium, lead and nickel - have been quantified in 10 fish species consumed by people living in the Nenets and Chukotka Regions. Fish muscle was analysed by ICP-MS after nitric acid or tetramethylammonium hydroxide digestion. Certified reference materials were employed and concentrations are reported as geometric means (GMs). Atlantic cod (6.32 mg/kg) and navaga (0.934 mg/kg) contained substantially higher amounts of I than all other fish species, while broad whitefish had the lowest (0.033 mg/kg). By comparison, navaga contained more Br (14.5 mg/kg) than the other fish species, ranging 7.45 mg/kg in Atlantic cod to 2.39 mg/kg in northern pike. A significant inter-fish association between As and I in freshwater and marine fish was observed, suggesting common sources and perhaps parallel absorption patterns. Only Atlantic cod and, to lesser extent, navaga constituted significant dietary sources of I.

Health Risk Modifiers of Exposure to Persistent Pollutants among Indigenous Peoples of Chukotka.

The aim of the study was to assess temporal trends in health risks related to most common persistent contaminants, including polychlorinated biphenyls (PCBs), dichloro-diphenyl-trichloroethanes (DDTs), lead (Pb), as well as mercury (Hg) among indigenous peoples living in coastal areas of Chukotka in Arctic Russia. This is examined in relation to exposure pathways and a range of social and behavioral factors capable of modifying the exposure to these contaminants, including place of residence, income, traditional subsistence, alcohol consumption, and awareness of risk prevention. The primary exposure pathway for PCBs is shown to be the intake of traditional foods, which explained as much as 90% of the total health risk calculated employing established risk guidelines. Nearly 50% of past DDT-related health risks also appear to have been contributed by contaminated indoor surfaces involving commonly used DDT-containing insecticides. Individuals who practiced traditional activities are shown to have experienced a 4.4-fold higher risk of exposure to PCBs and a 1.3-fold higher risk for DDTs, Pb, and Hg. Low income, high consumption of marine mammal fat, alcohol consumption, and lack of awareness of health risk prevention are attributed to a further 2- to 6-fold increase in the risk of PCBs exposure. Low socioeconomic status enhances the health risks associated with exposure to the persistent contaminants examined.

Concentration dataset for 4 essential and 5 non-essential elements in fish collected in Arctic and sub-Arctic territories of the Nenets Autonomous and Arkhangelsk regions of Russia.

The raw concentration data for the research article entitled "Essential and non-essential trace elements in fish consumed by indigenous peoples of the European Russian Arctic" (Sobolev et al., 2019) [1] are herein presented. Fifteen fish species were collected in the Nenets Autonomous and Arkhangelsk Regions of the Russian Federation and were analysed for 9 elements (As, Cd, Co, Cu, Hg, Ni, Pb, Se and Zn). The sampling sites were located in the European parts of the Russian Arctic and sub-Arctic territories. Within these territories, Nenets indigenous peoples commonly catch and consume local fish. Based on questionnaire data, local fish sources constituted ∼ 90% of the total fish consumed by endemic individuals living in these regions. The data summarized in this publication fill a gap in knowledge.

Essential and non-essential trace elements in fish consumed by indigenous peoples of the European Russian Arctic.

In present study, the analyses of essential [copper (Cu), cobalt (Co), selenium (Se) and zinc (Zn)] and non-essential elements [mercury (Hg), lead (Pb), cadmium (Cd) and arsenic (As)] in 7 fish species consumed by the indigenous people of the European Russia Arctic were conducted. The Nenets Autonomous Region, which is located in the north-eastern part of European Russia, was chosen as a Region of interest. Within it, the Nenets indigenous group (n = 6000) constitutes approximately 10% of the total population. Nearly all of the Nenets live a traditional life with fish caught in the local waters as a subsistence resource. We found that northern pike contained twice the amount of Hg compared with roach, and 3-4 times more than other fish species commonly consumed in the Russian Arctic (namely, Arctic char, pink salmon, navaga, humpback whitefish and inconnu). Fish Hg concentrations were relatively low, but comparable to those reported in other investigations that illustrate a decreasing south-to-north trend in fish Hg concentrations. In the current study, northern pike is the only species for which Hg bioaccumulated significantly. In all fish species, both Cd and Pb were present in considerably lower concentrations than Hg. The total As concentrations observed are similar to those previously published, and it is assumed to be present primarily in non-toxic organic forms. All fish tissues were rich in the essential elements Se, Cu and Zn and, dependent on the amount fish consumed, may contribute significantly to the nutritional intake by indigenous Arctic peoples. We observed large significant differences in the molar Se/Hg ratios, which ranged from 2.3 for northern pike to 71.1 for pink salmon. Values of the latter <1 may increase the toxic potential of Hg, while those >1 appear to enhance the protection against Hg toxicity.

A study of atherothrombotic biomarkers in welders.

INTRODUCTION: Studies have shown that welders have increased cardiovascular mortality. This may be due to airborne particulate matter (PM) exposure. Elevated levels of PM in polluted urban air have been associated with increased cardiovascular mortality and morbidity. This study seeks to explore potential mechanisms for the increased cardiovascular mortality in welders. METHODS: Seventy welders were compared to 74 referents. Exposure to PM was assessed by personal full-shift sampling of work room air the last 2 days before collection of blood samples. Selected biomarkers of pro-coagulant activity, endothelial/platelet activation and systemic inflammation were determined in the samples. RESULTS: The welders had been occupationally exposed to PM for 15 years on average. The geometric mean current exposure to PM was 8.1 mg/m3. They had statistically significantly higher concentrations of TNF-α, P-selectin, CD40L, prothrombin fragment 1 + 2 and D-dimer than the referents. Increasing concentrations of D-dimer and CD40L were observed by increasing current exposure to PM. DISCUSSION: The study shows that welders highly exposed to welding PM were in a pro-thrombotic state with increased thrombin generation and consequently higher D-dimer concentrations. The welders had also increased endothelial/platelet activation as compared to the referents. These alterations are compatible with increased cardiovascular mortality as previously reported among welders.

Workplace exposure to particulate matter, bio-accessible, and non-soluble metal compounds during hot work processes.

While exposure to air contaminants from metal arc welding at workplaces has been intensively investigated over the last five decades, other hot work processes, such as flame and plasma cutting, air carbon arc gouging, and surface grinding have not received as much attention. Exposures to particulate matter (PM) during selected hot work processes, such as metal active gas (MAG) and manual metal arc (MMA) welding, flame and plasma cutting, air carbon arc gouging, and surface grinding were measured. Respirable, inhalable, and "total" fractions of the PM were collected with different air samplers in the workers' breathing zone. Concentrations of PM, chromium (Cr), iron (Fe), manganese (Mn), molybdenum (Mo), nickel (Ni), copper (Cu), and lead (Pb) were determined in the samples by using gravimetric analysis and plasma-based analytical atomic spectrometry techniques. Bio-accessibility of the elements was investigated by using a synthetic lung lining fluid (Hatch´s solution) for the leaching of soluble metal compounds in the collected samples. Short term (15-75 min) workplace air concentrations of PM, Cr, Fe, Mn, Ni and Cu in the workers´ breathing zone during hot work processes were found to be high compared to the current 8-hr time-weighted average (TWA) exposure limit values (ELVs) in use in many countries. The short-term median concentrations of PM during the different hot work processes varied between 6.0 and 88.7 mg m-3 and between 15.1 and 193 mg m-3 in the respirable and inhalable fractions, respectively. The highest median concentration of Fe (107 mg m-3) and Mn (28.7 mg m-3) was found in the inhalable fraction during plasma cutting and air carbon arc gouging, respectively. More than 40% of the inhalable PM generated during flame and plasma cutting, air carbon arc gouging and surface grinding was present in the respirable fraction. There was large variation in the bio-accessibility of the elements in PM collected during the different hot work processes.

Size distribution and single particle characterization of airborne particulate matter collected in a silicon carbide plant.

The global SiC market is projected to grow in the coming years, and research on potential health effects as well as epidemiological studies is therefore of importance. A detailed characterization in terms of the phase composition, morphology and mixing state of airborne PM is still missing, though highly necessary to identify sources and to understand the risk factors in this industry. Particles in the size range of 10 nm to 10 µm were collected with a 13-stage NanoMOUDI impactor in the Acheson Furnace Hall as well as in processing departments during two sampling campaigns. Particle mass concentrations, including the fraction of ultrafine particles (UFPs), were lower in the processing departments in comparison to those in the Acheson Furnace Hall. The particle number size distribution measured with a scanning mobility particle sizer confirmed the low amount of UFPs in the processing departments compared to the furnace hall. Significant differences in the particle mass concentration and distribution were observed in the Acheson Furnace Hall during the two sampling campaigns. The PM size distribution depends upon the sampling location, on the cycle of the nearby furnaces and on special incidents occurring during a furnace run. Scanning and transmission electron microscopy (SEM and TEM) showed that the size range of 0.32-10 µm (aerodynamic diameter) is dominated by carbon (C)-rich particles, which were identified as petroleum coke, graphite, soot and amorphous spherical C-rich particles. Soot was further classified into three types based on the primary particle size, morphology and composition. Diesel-powered vehicles, pyrolysis of petroleum coke and incomplete combustion of volatile components from this pyrolysis are suggested as sources of different soot particle types. Amorphous spherical C-rich particles were also sub-classified based on their morphology and composition as tar balls (TBs) and C-spherical type 2. The amount of SiC fibers and crystalline SiO2 was found to be low. In the size fraction below 0.32 µm (aerodynamic diameter), sulphur (S)-rich particles dominate. This knowledge of the particle size distribution, and chemical and physical properties of the PM occurring in the SiC production is fundamental for an appropriate risk assessment, and these findings should have implications for future epidemiological studies and for the mitigation of worker exposure.