Carbon-Fiber-Recycling Strategies: A Secondary Waste Stream Used for PA6,6 Thermoplastic Composite Applications.

With a view to achieving sustainable development and a circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with a PA6,6 polymer matrix. The reinforcing fibers implemented in the research are the result of a double-recovery action: starting with pyrolysis, long fibers are obtained, which are used to produce non-woven fabrics, and subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of different amounts of reinforcement at 5% and 10% by weight on the mechanical properties of 3D-printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via the fused deposition modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 5% and 21% compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+9% over the neat sample). Next, a prediction of the "optimum" critical length of carbon fibers was proposed that could be used for future optimization of recycled fiber processing.

Novel terephthalamide diol monomers synthesis from PET waste to Poly(Urethane acrylates).

Due to its excellent properties, poly(ethylene terephthalate) (PET) is one of the most produced and consumed polymers. Among plastics, it represents the main contributor to environmental pollution. Following the circular economy model, the chemical upcycling of PET reduces the amount of waste generated and transforms it into high-value products. The depolymerization of poly(ethylene terephthalate) into oligomers or monomers leads to forming a library of reactive molecules involved in different polymerization processes to obtain compounds with improved properties. Herein, several ß-hydroxy amines were synthesized and used for the chemical recycling of water bottle waste by an environmental benefit aminolysis process to get very useful new terephthalamide diol monomers. The recycled diol monomers were subsequently exploited to synthesize poly(urethane acrylates) (PUAs) UV-curable coatings, and their chemical, thermal and mechanical characterizations were performed. The results show the great potential of the developed synthesis protocols to obtain PUAs with final properties that can be modulated to meet the requirements of different applications.

Anaerobic biodegradation of disposable PLA-based products: Assessing the correlation with physical, chemical and microstructural properties.

In the present study commercial Polylactic Acid-based disposable cups and plates were selected for lab scale anaerobic degradability tests. The experiments were carried out under thermophilic conditions at different inoculum to substrate ratios and test material sizes, and the specific biogas production and associated kinetics were evaluated. Maximum biogas production was comparable for almost all the experimental runs (1620 and 1830 NmL/gTOCPLA) and a biodegradation degree in the range 86-100% was attained. Moreover, physical, chemical and microscopical analyses were used to characterize the tested materials before and after the degradation. The products composition was assessed and the presence of some additives (mainly Ca-based) was detected. Potential correlations among the process parameters and product composition were derived and a delay in process kinetics with increasing amount of additives embedded in the polymeric matrix was observed, confirming the relevant influence of the chemical blend on the biodegradation process.

Low Molecular Weight Bio-Polyamide 11 Composites Reinforced with Flax and Intraply Flax/Basalt Hybrid Fabrics for Eco-Friendlier Transportation Components.

The transportation sector is striving to meet the more severe European legislation which encourages all industrial fields to embrace more eco-friendly policies by exploiting constituents from renewable resources. In this framework, the present work assessed the potential of a bio-based, low molecular weight PA11 matrix reinforced with flax and intraply flax/basalt hybrid fabrics. To this aim, both quasi-static and impact performance were addressed through three-point bending and low-velocity impact tests, respectively. For hybrid composites, the effect of stacking sequence, i.e., [0/0] and [0/90], and fiber orientation were considered, while the effect of temperature, i.e., -40 °C, room temperature and +45 °C, was investigated for laminates' impact response. The mechanical experimental campaign was supported by thermal and morphological analyses. The results disclosed an improved processability of the low molecular weight PA11, which ensured a manufacturing temperature of 200 °C, which is fundamental to minimize flax fibers' thermal degradation. Both quasi-static and impact properties demonstrated that hybridization is a good solution for obtaining good mechanical properties while preserving laminates' lightness and biodegradability. The [0/90] configuration proved to be the best solution, providing satisfying flexural performance, with an increase between 62% and 83% in stiffness and between 19.6% and 37.6% in strength compared to flax-based laminates, and the best impact performance, with a reduction in permanent indentation and back crack extent.

Chemical, Thermal and Mechanical Characterization of Licorice Root, Willow, Holm Oak, and Palm Leaf Waste Incorporated into Maleated Polypropylene (MAPP).

The effect of four lignocellulosic waste fillers on the thermal and mechanical properties of biocomposites was investigated. Powdered licorice root, palm leaf, holm oak and willow fillers were melt compounded with polypropylene at two different weight contents, i.e., 10 and 30, and then injection molded. A commercially available maleated coupling agent was used to improve the filler/matrix interfacial adhesion at 5 wt.%. Composites were subjected to chemical (FTIR-ATR), thermal (TGA, DSC, DMA) and mechanical (tensile, bending and Charpy impact) analyses coupled with a morphological investigation by scanning electron microscopy. Although similarities among the different formulations were noted, holm oak fillers provided the best combination of thermal and mechanical performance. In particular, at 30 wt.% content with coupling agent, this composite formulation displayed remarkable increases in tensile strength and modulus, flexural strength and modulus, of 28% and 110%, 58% and 111%, compared to neat PP, respectively. The results imply that all these lignocellulosic waste fillers can be used successfully as raw materials for biocomposites, with properties comparable to those featured by other natural fillers.

Recycled Multi-Material Packaging Reinforced with Flax Fibres: Thermal and Mechanical Behaviour.

In this work, the use of a recycled mix stemming from the treatment of multilayer aseptic packaging used in the food and beverage industry is proposed as the matrix for short fibre composites reinforced with flax fibres, to generate value-added materials in contrast to the more common end-of-life scenario including energy recovery. This is expected to be a preferred choice in the waste hierarchy at the European level. A commercially available material (EcoAllene) obtained from multilayer packaging recycling was compounded with short flax fibres up to 30 wt.% by twin screw extrusion, with a view to enhancing its poor mechanical profile and broadening its applications. Composites were in depth analyzed by thermogravimetric analysis and differential scanning calorimetry, which highlighted the complex nature of this recycled product, a limited nucleation ability of flax fibres and a lower thermal stability due to the premature degradation of natural hemicellulose and cellulose, though featuring in any case onset degradation temperatures higher than 300 °C. Composites' mechanical properties were assessed in tension, bending and impact conditions, with remarkable improvements over the neat matrix in terms of stiffness and strength. In particular, at 30 wt.% fibre content and with 5 wt.% of maleated coupling agent, an increase in tensile and flexural strength values by 92% and 138% was achieved, respectively, without compromising the impact strength. The effectiveness of flax fibres confirmed by dynamo-mechanical analysis is beneficial to the exploitation of these composites in automotive interiors and outdoor decking applications.

Hierarchical Flax Fibers by ZnO Electroless Deposition: Tailoring the Natural Fibers/Synthetic Matrix Interphase in Composites.

Hierarchical functionalization of flax fibers with ZnO nanostructures was achieved by electroless deposition to improve the interfacial adhesion between the natural fibers and synthetic matrix in composite materials. The structural, morphological, thermal and wetting properties of the pristine and ZnO-coated flax fibers were investigated. Thus, the ZnO-coated flax fabric discloses an apparent contact angle of ~140° immediately after the placement of a water droplet on its surface. An assessment of the interfacial adhesion at the yarn scale was also carried out on the flax yarns coated with ZnO nanostructures. Thus, after the ZnO functionalization process, no significant degradation of the tensile properties of the flax yarns occurs. Furthermore, the single yarn fragmentation tests revealed a notable increase in the interfacial adhesion with an epoxy matrix, reductions of 36% and 9% in debonding and critical length values being measured compared to those of the pristine flax yarns, respectively. The analysis of the fracture morphology by scanning electron microscopy and X-ray microtomography highlighted the positive role of ZnO nanostructures in restraining debonding phenomena at the flax fibers/epoxy resin matrix interphase.

Fused Deposition Modeling Parameter Optimization for Cost-Effective Metal Part Printing.

Metal 3D-printed parts are critical in industries such as biomedical, surgery, and prosthetics to create tailored components for patients, but the costs associated with traditional metal additive manufacturing (AM) techniques are typically prohibitive. To overcome this disadvantage, more cost-effective manufacturing processes are needed, and a good approach is to combine fused deposition modeling (FDM) with debinding-sintering processes. Furthermore, optimizing the printing parameters is required to improve material density and mechanical performance. The design of experiment (DoE) technique was used to evaluate the impact of three printing factors, namely nozzle temperature, layer thickness, and flow rate, on the tensile and bending properties of sintered 316L stainless steel in this study. Green and sintered samples were morphologically and physically characterized after printing, and the optimal printing settings were determined by statistical analysis, which included the surface response technique. The mechanical properties of the specimens increased as the flow rate and layer thickness increased and the nozzle temperature decreased. The optimized printing parameters for the ranges used in this study include 110% flow rate, 140 µm layer thickness, and 240 °C nozzle temperature, which resulted in sintered parts with a tensile strength of 513 MPa and an elongation at break of about 60%.

Solvent Casting and UV Photocuring for Easy and Safe Fabrication of Nanocomposite Film Dressings.

The aim of this work was to optimize and characterize nanocomposite films based on gellan gum methacrylate (GG-MA) and silver nanoparticles (AgNPs) for application in the field of wound dressing. The films were produced using the solvent casting technique coupled with a photocuring process. The UV irradiation of GG-MA solutions containing glycerol as a plasticizer and different amounts of silver nitrate resulted in the concurrent crosslinking of the photocurable polymer and a reduction of Ag ions with consequent in situ generation of AgNPs. In the first part of the work, the composition of the films was optimized, varying the concentration of the different components, the GG-MA/glycerol and GG-MA/silver nitrate weight ratios as well as the volume of the film-forming mixture. Rheological analyses were performed on the starting solutions, whereas the obtained films were characterized for their mechanical properties. Colorimetric analyses and swelling studies were also performed in order to determine the AgNPs release and the water uptake capacity of the films. Finally, microbiological tests were carried out to evaluate the antimicrobial efficacy of the optimized films, in order to demonstrate their possible application as dressings for the treatment of infected hard-to-heal wounds, which is a demanding task for public healthcare.

Organic residue analysis reveals the function of bronze age metal daggers.

The article discusses results of organic residue analysis performed on ten copper-alloy daggers from Bronze Age Pragatto, Italy, c.1550-1250 BCE. Metal daggers are widespread in Chalcolithic and Bronze Age Europe, yet their social and practical roles are still hotly debated. Are they symbolic or functional? Are they tools or weapons? How were they used? For what tasks and on what materials? The research addresses these questions through a novel application of biochemical staining and SEM-EDX analysis. The method has proved successful in extracting and identifying animal residues located on cutting edges including bone, muscle, and tendons. These are interpreted as evidence of prehistoric carcass butchering and carving. Further residues were observed on blade faces and hafting plates or tangs; these are interpreted as remnants of bone handles and sheaths, the latter made of either wood fibers or processed hide and fur. The readings proposed in the article are validated by original experiments with replica daggers, as detailed in the Supplementary Materials. The analysis and experiments shed new light on Bronze Age metal daggers, showing that they were fully functional tools (and perhaps tool-weapons) primarily utilized for the processing of animal carcasses. This original research result contributes significant knowledge towards interpreting an under-studied, yet socially salient, prehistoric metal artifact.

Effect of Aging on the Mechanical Properties of Highly Transparent Fluoropolymers for the Conservation of Archaeological Sites.

In recent years, fluoropolymers have found numerous applications in the architectural field because of their combination of mechanical-chemical resistance and high transparency. In the present work, commercial fluorinated polymers, such as perfluoro alkoxy (PFA) and ethylene tetrafluoroethylene copolymer (ETFE), have been evaluated for use as protective and transparent layers on monumental and archaeological sites (to preserve mosaics or frescoes) during the phases of restoration or maintenance outdoors. Considering this specific application, the present study was developed by evaluating the evolution of the mechanical (tensile, tear propagation resistance, and low-velocity impact tests) and chemical (FTIR and DSC analysis) properties of the films after accelerated UV aging. The results that were obtained demonstrated the high resistance capacity of the ETFE, which exhibits considerably higher elastic modulus and critical tear energy values than PFA films (1075.38 MPa and 131.70 N/mm for ETFE; 625.48 MPa and 59.06 N/mm for PFA). After aging, the samples exhibited only a slight reduction of about 5% in the elastic modulus for both polymers and 10% in the critical tear energy values for PFA. Furthermore, the differences in impact resistance after aging were limited for both polymers; however, the ETFE film showed higher peak force than the PFA films (82.95 N and 42.22 N, respectively). The results obtained demonstrated the high resistance capacity of ETFE films, making them the most suitable candidate for the considered application.

Chemical and Mechanical Characterization of Licorice Root and Palm Leaf Waste Incorporated into Poly(urethane-acrylate) (PUA).

A poly(urethane-acrylate) polymer (PUA) was synthesized, and a sufficiently high molecular weight starting from urethane-acrylate oligomer (UAO) was obtained. PUA was then loaded with two types of powdered ligno-cellulosic waste, namely from licorice root and palm leaf, in amounts of 1, 5 and 10%, and the obtained composites were chemically and mechanically characterized. FTIR analysis of final PUA synthesized used for the composite production confirmed the new bonds formed during the polymerization process. The degradation temperatures of the two types of waste used were in line with what observed in most common natural fibers with an onset at 270 °C for licorice waste, and at 290 °C for palm leaf one. The former was more abundant in cellulose (44% vs. 12% lignin), whilst the latter was richer in lignin (30% vs. 26% cellulose). In the composites, only a limited reduction of degradation temperature was observed for palm leaf waste addition and some dispersion issues are observed for licorice root, leading to fluctuating results. Tensile performance of the composites indicates some reduction with respect to the pure polymer in terms of tensile strength, though stabilizing between data with 5 and 10% filler. In contrast, Shore A hardness of both composites slightly increases with higher filler content, while in stiffness-driven applications licorice-based composites showed potential due to an increase up to 50% compared to neat PUA. In general terms, the fracture surfaces tend to become rougher with filler introduction, which indicates the need for optimizing interfacial adhesion.

Commercial Bio-Packaging to Preserve the Quality and Extend the Shelf-Life of Vegetables: The Case-Study of Pumpkin Samples Studied by a Multimethodological Approach.

A multidisciplinary protocol is proposed to monitor the preservation of fresh pumpkin samples (FP) using three commercial polymeric films: A made of biodegradable cellophane from regenerated cellulose pulp; B from corn starch, cassava and eucalyptus, C made of polylactic acid from corn starch, and a polyethylene film used as reference (REF). Chemical, mechanical and microbiological analyses were applied on packaging and fresh and packaged samples at different times. After an 11-day period, NMR spectroscopy results showed a sucrose increase and a malic acid decrease in all the biofilms with respect to FP; fructose, glucose, galactose levels remained quite constant in biofilms B and C; the most abundant amino acids remained quite constant in biofilm A and decreased significantly in biofilm B. From microbiological analyses total microbial count was below the threshold value up to 7 days for samples in all the films, and 11 days for biofilm C. The lactic acid bacteria, and yeasts and molds counts were below the acceptability limit during the 11 days for all packages. In the case of biofilm C, the most promising packaging for microbiological point of view, aroma analysis was also carried out. In this paper, you can find all the analysis performed and all the values found.

Zinc oxide nanostructures and stearic acid as surface modifiers for flax fabrics in polylactic acid biocomposites.

Different surface treatments including mercerization, stearic acid and growth of zinc oxide nanorods as well as their combinations were exploited to address their effects on the properties of green composites based on polylactic acid (PLA) and flax fabrics. The resulting fabrics were morphologically (SEM), crystallographically (XRD) and thermally (TGA) characterized, showing no significant changes with respect to the untreated samples. In contrast, tensile and flexural properties of composites produced by compression moulding were significantly influenced. A combination of mercerization and environmentally friendly stearic acid treatment turned the character of the flax fabric from hydrophilic to hydrophobic, and led to improved bending and tensile strengths by 20% and 12%, respectively, compared to untreated composites. The presence of ZnO nanorods promoted an increase in flexural and tensile stiffness by 58% and 31%, respectively, but at the expense of strength, with reductions ascribed to the degradation of polylactic acid under high-temperature conditions favoured by ZnO, as confirmed by a reduction in the initial thermal degradation temperature up to 26%. These latter composites can be suggested in those applications where a suitable combination of flexural properties and a shorter persistence in the environment is desired.

Functionalization of Commercial Electrospun Veils with Zinc Oxide Nanostructures.

The present research is focused on the synthesis of hexagonal ZnO wurtzite nanorods for the decoration of commercially available electrospun nylon nanofibers. The growth of ZnO was performed by a hydrothermal technique and for the first time on commercial electrospun veils. The growth step was optimized by adopting a procedure with the refresh of growing solution each hour of treatment (Method 1) and with the maintenance of a specific growth solution volume for the entire duration of the treatment (Method 2). The overall treatment time and volume of solution were also optimized by analyzing the morphology of ZnO nanostructures, the coverage degree, the thermal and mechanical stability of the obtained decorated electrospun nanofibers. In the optimal synthesis conditions (Method 2), hexagonal ZnO nanorods with a diameter and length of 53.5 nm ± 5.7 nm and 375.4 nm ± 37.8 nm, respectively, were obtained with a homogeneous and complete coverage of the veils. This easily scalable procedure did not damage the veils that could be potentially used as toughening elements in composites to prevent delamination onset and propagation. The presence of photoreactive species makes these materials ideal also as environmentally friendly photocatalysts for wastewater treatment. In this regard, photocatalytic tests were performed using methylene blue (MB) as model compound. Under UV light irradiation, the degradation of MB followed a first kinetic order data fitting and after 3 h of treatment a MB degradation of 91.0% ± 5.1% was achieved. The reusability of decorated veils was evaluated and a decrease in photocatalysis efficiency was detected after the third cycle of use.

Surface Modification of Basalt Fibres with ZnO Nanorods and Its Effect on Thermal and Mechanical Properties of PLA-Based Composites.

The composites based on basalt fibres and poly(lactic acid) (PLA) show promising applications in biomedical and automotive fields, but their mechanical performance is still largely hindered by poor interfacial properties. Zinc oxide nanorods have been successfully used to tune the PLA/basalt fibre interface by growing them on commercially available basalt fabrics. The hierarchical fibres significantly enhanced the mechanical properties of PLA-based composites, especially their flexural strength and stiffness. These values are 26% and 22% higher than those of unmodified basalt/PLA composites, and 24% and 34% higher than those of glass/PLA composites used as a baseline. The increase in tensile and flexural properties hinges on the mechanical interlocking action promoted by ZnO nanorods and on the creation of a compact transcrystallinity structure. A degradation of PLA matrix was detected but it was positively counteracted by the better interfacial stress transfer. This study offers a novel approach for modifying the fibre-matrix interface of biocomposites intended for high-performance applications.

An integrated study discloses chopping tools use from Late Acheulean Revadim (Israel).

Chopping tools/choppers provide one of the earliest and most persistent examples of stone tools produced and used by early humans. These artifacts appeared for the first time ~2.5 million years ago in Africa and are characteristic of the Oldowan and Acheulean cultural complexes throughout the Old World. Chopping tools were manufactured and used by early humans for more than two million years regardless of differences in geography, climate, resource availability, or major transformations in human cultural and biological evolution. Despite their widespread distribution through time and space in Africa and Eurasia, little attention has been paid to the function of these items, while scholars still debate whether they are tools or cores. In this paper, we wish to draw attention to these prominent and ubiquitous early lithic artifacts through the investigation of 53 chopping tools retrieved from a specific context at Late Acheulean Revadim (Israel). We combined typo-technological and functional studies with a residue analysis aimed at shedding light on their functional role within the tool-kits of the inhabitants of the site. Here we show that most of the chopping tools were used to chop hard and medium materials, such as bone, most probably for marrow extraction. A few of the tools were also used for cutting and scraping activities, while some also served as cores for further flake detachment. The chopping tools exhibit extraordinarily well-preserved bone residues suggesting they were used mainly for bone-breaking and marrow acquisition. We discuss the data and explore the tool versus core debate also in light of a sample of 50 flake cores made on pebbles/cobbles retrieved from the same archeological layer. The results add further pieces to the puzzle of activities carried out at Revadim and add to our knowledge of the production and use of these enigmatic tools and their role in human evolutionary history.

The Compressive Behavior and Crashworthiness of Cork: A Review.

Cork, a natural material from renewable resources, is currently attracting increasing interest in different industrial fields because of its cellular structure and the presence of the flexible suberin as its main chemical component. In an agglomerated form, it proved to be a compelling product not only as a thermal and acoustic insulator, but also as core material in sandwich structures and as a liner or padding in energy absorbing equipment. From this perspective, the assessment of its compressive response is fundamental to ensure the right out-of-plane stiffness required to a core material and the proper crashworthiness in the safety devices. Considering the complex nature of cork and the resulting peculiar compressive response, the present review article provides an overview of this paramount property, assessing the main parameters (anisotropy, temperature, strain rate, etc.) and the peculiar features (near-zero Poisson's ratio and unique dimensional recovery) that characterize it in its natural state. Furthermore, considering its massive exploitation in the agglomerated form, the design parameters that allow its compressive behavior to be tailored and the operating parameters that can affect its crashworthiness were assessed, reporting some potential industrial applications.

Hybrid Cellulose-Basalt Polypropylene Composites with Enhanced Compatibility: The Role of Coupling Agent.

This study deals with the development and optimization of hybrid composites integrating microcrystalline cellulose and short basalt fibers in a polypropylene (PP) matrix to maximize the mechanical properties of resulting composites. To this aim, the effects of two different coupling agents, endowed with maleic anhydride (MA-g(grafted)-PP) and acrylic acid (AA-g-PP) functionalities, on the composite properties were investigated as a function of their amount. Tensile, flexural, impact and heat deflection temperature tests highlighted the lower reactivity and effectiveness of AA-g-PP, regardless of reinforcement type. Hybrid formulations with basalt/cellulose (15/15) and with 5 wt. % of MA-g-PP displayed remarkable increases in tensile strength and modulus, flexural strength and modulus, and notched Charpy impact strength, of 45% and 284%, 97% and 263%, and 13%, in comparison with neat PP, respectively. At the same time, the thermo-mechanical stability was enhanced by 65% compared to neat PP. The results of this study, if compared with the ones available in the literature, reveal the ability of such a combination of reinforcements to provide materials suitable for automotive applications with environmental benefits.

Development of Thermoplastic Starch (TPS) Including Leather Waste Fragments.

A thermoplastic starch (TPS) material is developed, based on corn starch plasticized with glycerol and citric acid in a 9:3:1 ratio and further bonded with isinglass and mono- and diglycerides of fatty acids (E471). In TPS, leather fragments, in the amount of 7.5 15 or 22.5 g/100 g of dry matter, were also introduced. The mixture was heated at a maximum temperature of 80 °C, then cast in an open mold to obtain films with thickness in the range 300 ± 50 microns. The leather fragments used were based on collagen obtained from production waste from shoemaking and tanned with tannins obtained from smoketree (Rhus cotinus), therefore free from chromium. Thermogravimetric (TGA) tests suggested that material degradation started at a temperature around 285 °C, revealing that the presence of leather fragments did not influence the occurrence of this process in TPS. Tensile tests indicated an increase in tensile properties (strength and Young's modulus) with increasing leather content, albeit coupled, especially at 22.5 wt%, with a more pronounced brittle behavior. Leather waste provided a sound interface with the bulk of the composite, as observed under scanning electron microscopy. The production process indicated a very limited degradation of the material after exposure to UV radiation for eight days, as demonstrated by the slight attenuation of amide I (collagen) and polysaccharide FTIR peaks. Reheating at 80 °C resulted in a weight loss not exceeding 3%.