Surface-coating regulated lithiation kinetics and degradation in silicon nanowires for lithium ion battery.

Silicon (Si)-based materials hold promise as the next-generation anodes for high-energy lithium (Li)-ion batteries. Enormous research efforts have been undertaken to mitigate the chemo-mechanical failure due to the large volume changes of Si during lithiation and delithiation cycles. It has been found that nanostructured Si coated with carbon or other functional materials can lead to significantly improved cyclability. However, the underlying mechanism and comparative performance of different coatings remain poorly understood. Herein, using in situ transmission electron microscopy (TEM) through a nanoscale half-cell battery, in combination with chemo-mechanical simulation, we explored the effect of thin (∼5 nm) alucone and Al2O3 coatings on the lithiation kinetics of Si nanowires (SiNWs). We observed that the alucone coating leads to a "V-shaped" lithiation front of the SiNWs, while the Al2O3 coating yields an "H-shaped" lithiation front. These observations indicate that the difference between the Li surface diffusivity and bulk lithiation rate of the coatings dictates lithiation induced morphological evolution in the nanowires. Our experiments also indicate that the reaction rate in the coating layer can be the limiting step for lithiation and therefore critically influences the rate performance of the battery. Further, the failure mechanism of the Al2O3 coated SiNWs was also explored. Our studies shed light on the design of high capacity, high rate and long cycle life Li-ion batteries.

In situ transmission electron microscopy probing of native oxide and artificial layers on silicon nanoparticles for lithium ion batteries.

Surface modification of silicon nanoparticles via molecular layer deposition (MLD) has been recently proved to be an effective way for dramatically enhancing the cyclic performance in lithium ion batteries. However, the fundamental mechanism of how this thin layer of coating functions is not known, which is complicated by the inevitable presence of native oxide of several nanometers on the silicon nanoparticle. Using in situ TEM, we probed in detail the structural and chemical evolution of both uncoated and coated silicon particles upon cyclic lithiation/delithation. We discovered that upon initial lithiation, the native oxide layer converts to crystalline Li2O islands, which essentially increases the impedance on the particle, resulting in ineffective lithiation/delithiation and therefore low Coulombic efficiency. In contrast, the alucone MLD-coated particles show extremely fast, thorough, and highly reversible lithiation behaviors, which are clarified to be associated with the mechanical flexibility and fast Li(+)/e(-) conductivity of the alucone coating. Surprisingly, the alucone MLD coating process chemically changes the silicon surface, essentially removing the native oxide layer, and therefore mitigates side reactions and detrimental effects of the native oxide. This study provides a vivid picture of how the MLD coating works to enhance the Coulombic efficiency, preserves capacity, and clarifies the role of the native oxide on silicon nanoparticles during cyclic lithiation and delithiation. More broadly, this work also demonstrates that the effect of the subtle chemical modification of the surface during the coating process may be of equal importance to the coating layer itself.

Reversible high-capacity Si nanocomposite anodes for lithium-ion batteries enabled by molecular layer deposition.

The molecular-layer deposition of a flexible coating onto Si electrodes produces high-capacity Si nanocomposite anodes. Using a reaction cascade based on inorganic trimethylaluminum and organic glycerol precursors, conventional nano-Si electrodes undergo surface modifications, resulting in anodes that can be cycled over 100 times with capacities of nearly 900 mA h g(-1) and Coulombic efficiencies in excess of 99%.

Atomic layer deposition of amorphous TiO2 on graphene as an anode for Li-ion batteries.

Atomic layer deposition (ALD) was used to deposit TiO2 anode material on high surface area graphene (reduced graphene oxide) sheets for Li-ion batteries. An Al2O3 ALD ultrathin layer was used as an adhesion layer for conformal deposition of the TiO2 ALD films at 120 ° C onto the conducting graphene sheets. The TiO2 ALD films on the Al2O3 ALD adhesion layer were nearly amorphous and conformal to the graphene sheets. These nanoscale TiO2 coatings minimized the effect of the low diffusion coefficient of lithium ions in bulk TiO2. The TiO2 ALD films exhibited stable capacities of ~120 mAh g(-1) and ~100 mAh g(-1) at high cycling rates of 1 A g(-1) and 2 A g(-1), respectively. The TiO2 ALD films also displayed excellent cycling stability with ~95% of the initial capacity remaining after 500 cycles. These results illustrate that ALD can provide a useful method to deposit electrode materials on high surface area substrates for Li-ion batteries.

Ultrathin oxide films by atomic layer deposition on graphene.

In this paper, a method is presented to create and characterize mechanically robust, free-standing, ultrathin, oxide films with controlled, nanometer-scale thickness using atomic layer deposition (ALD) on graphene. Aluminum oxide films were deposited onto suspended graphene membranes using ALD. Subsequent etching of the graphene left pure aluminum oxide films only a few atoms in thickness. A pressurized blister test was used to determine that these ultrathin films have a Young's modulus of 154 ± 13 GPa. This Young's modulus is comparable to much thicker alumina ALD films. This behavior indicates that these ultrathin two-dimensional films have excellent mechanical integrity. The films are also impermeable to standard gases suggesting they are pinhole-free. These continuous ultrathin films are expected to enable new applications in fields such as thin film coatings, membranes, and flexible electronics.