Chemically Accelerated Stabilization of a Cellulose-Lignin Precursor as a Route to High Yield Carbon Fiber Production.

The production of carbon fiber from bio-based or renewable resources has gained considerable attention in recent years with much of the focus upon cellulose, lignin, and cellulose-lignin composite precursor fibers. A critical step in optimizing the manufacture of carbon fiber is the stabilization process, through which the chemical and physical structure of the precursor fiber is transformed, allowing it to withstand very high temperatures. In this work, thermogravimetric analysis (TGA) is used to explore and optimize stabilization by simulating different stabilization profiles. Using this approach, we explore the influence of atmosphere (nitrogen or air), cellulose-lignin composition, and alternative catalysts on the carbon yield, efficiency, and rate of stabilization. Carbon dioxide and water vapor released during stabilization are analyzed by Fourier transform infrared (FTIR) spectroscopy, providing further information about the stabilization mechanism and the accelerating effect of oxygen and increased char yield (carbon content), especially for lignin. A range of different catalysts are evaluated for their ability to enhance the char yield, and a phosphorus-based flame retardant (H3PO4) proved to be the most effective; in fact, a doubling of the char yield was observed.

Fast and quantitative compositional analysis of hybrid cellulose-based regenerated fibers using thermogravimetric analysis and chemometrics.

Cellulose can be dissolved with another biopolymer in a protic ionic liquid and spun into a bicomponent hybrid cellulose fiber using the Ioncell® technology. Inside the hybrid fibers, the biopolymers are mixed at the nanoscale, and the second biopolymer provides the produced hybrid fiber new functional properties that can be fine-tuned by controlling its share in the fiber. In the present work, we present a fast and quantitative thermoanalytical method for the compositional analysis of man-made hybrid cellulose fibers by using thermogravimetric analysis (TGA) in combination with chemometrics. First, we incorporated 0-46 wt.% of lignin or chitosan in the hybrid fibers. Then, we analyzed their thermal decomposition behavior in a TGA device following a simple, one-hour thermal treatment protocol. With an analogy to spectroscopy, we show that the derivative thermogram can be used as a predictor in a multivariate regression model for determining the share of lignin or chitosan in the cellulose hybrid fibers. The method generated cross validation errors in the range 1.5-2.1 wt.% for lignin and chitosan. In addition, we discuss how the multivariate regression outperforms more common modeling methods such as those based on thermogram deconvolution or on linear superposition of reference thermograms. Moreover, we highlight the versatility of this thermoanalytical method-which could be applied to a wide range of composite materials, provided that their components can be thermally resolved-and illustrate it with an additional example on the measurement of polyester content in cellulose and polyester fiber blends. The method could predict the polyester content in the cellulose-polyester fiber blends with a cross validation error of 1.94 wt.% in the range of 0-100 wt.%. Finally, we give a list of recommendations on good experimental and modeling practices for the readers who want to extend the application of this thermoanalytical method to other composite materials. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1007/s10570-021-03923-6.

Cellulose-lignin composite fibres as precursors for carbon fibres. Part 1 - Manufacturing and properties of precursor fibres.

Cellulose-lignin composite fibres were spun from ionic liquid (IL) solutions by dry-jet wet spinning. Birch pre-hydrolysed Kraft (PHK) pulp and organosolv beech (BL) or spruce lignin (SL) were dissolved in the IL 1,5-diazabicyclo[4.3.0]non-5-enium acetate ([DBNH]OAc) to prepare spinning dopes. Fibres with lignin concentrations of up to 50 % were spun successfully. The fibres were analysed focusing on important properties for the production of carbon fibres (CF). Due to the higher molar mass of the SL compared to the BL, SL showed higher stability in the spinning process, giving higher lignin content in the final fibres. The CF yield after carbonization increased with increasing lignin content. The higher carbon content of SL compared to BL, resulted in moderately higher CF yield of the SL fibres, compared to fibres with BL. Overall, the produced cellulose-lignin composite fibres show great potential as precursors for CF production.

Cellulose-lignin composite fibers as precursors for carbon fibers: Part 2 - The impact of precursor properties on carbon fibers.

Carbon fibers, despite being responsible lightweight structures that improve sustainability through fuel efficiency and occupational safety, remain largely derived from fossil fuels. Alternative precursors such as cellulose and lignin (bio-derived and low cost) are rapidly gaining attention as replacements for polyacrylonitrile (PAN, an oil-based and costly precursor). This study uses a cellulose-lignin composite fiber, to elucidate the influence of precursor fabrication parameters (draw ratio and lignin content) on the efficiency of stabilization and carbonization, from the perspective of the chemical, morphological and mechanical changes. The degradation of cellulose chains was the primary contributor to the decrease in mechanical properties during stabilization, but is slowed by the incorporation of lignin. The skin-core phenomenon, a typical effect in PAN-based carbon fibers production, was also observed. Finally, the carbonization of incompletely stabilized fibers is shown to produce hollow carbon fibers, which have potential application in batteries or membranes.

Fungal Treatment Modifies Kraft Lignin for Lignin- and Cellulose-Based Carbon Fiber Precursors.

The kraft lignin's low molecular weight and too high hydroxyl content hinder its application in bio-based carbon fibers. In this study, we were able to polymerize kraft lignin and reduce the amount of hydroxyl groups by incubating it with the white-rot fungus Obba rivulosa. Enzymatic radical oxidation reactions were hypothesized to induce condensation of lignin, which increased the amount of aromatic rings connected by carbon-carbon bonds. This modification is assumed to be beneficial when aiming for graphite materials such as carbon fibers. Furthermore, the ratio of remaining aliphatic hydroxyls to phenolic hydroxyls was increased, making the structure more favorable for carbon fiber production. When the modified lignin was mixed together with cellulose, the mixture could be spun into intact precursor fibers by using dry-jet wet spinning. The modified lignin leaked less to the spin bath compared with the unmodified lignin starting material, making the recycling of spin-bath solvents easier. The stronger incorporation of modified lignin in the precursor fibers was confirmed by composition analysis, thermogravimetry, and mechanical testing. This work shows how white-rot fungal treatment can be used to modify the structure of lignin to be more favorable for the production of bio-based fiber materials.