Comparison of volumetric loss and surface roughness of composite dental restorations obtained by additive and subtractive manufacturing methods.

Statement of problem: Permanent crown materials produced with new generation additive manufacturing and traditional subtractive manufacturing materials have not been compared in terms of wear resistance. Purpose: This study aims to compare the volumetric loss related to wear and resulting surface roughness after aging in a chewing simulator between resin nano ceramics produced with milling technique and permanent crown materials produced with three dimensional (3D) printing. Materials and methods: Three different hybrid composite-ceramic (HCC) (The three materials are GC: Cerasmart, VE: Vita Enamic, and GV: Grandio Voco.) and one 3D printed definitive crown resin (FormLabs Permanent Crown Resin) were investigated before aging (n:8), the surface roughness of all samples was measured with a profilometer, and 1 randomly selected sample from each subgroup was imaged with scanning electron microscope (SEM). 3D scans of each sample were obtained with a desktop scanner. Thermomechanical aging was performed using a chewing simulator. Four hundred thousand cycles were completed under a vertical occlusal force of 49 ± 0.7 N with a thermal cycle of 1.7 Hz 5-55° and with a dwell time of 120 s, mimicking 2 years of aging. The imaging procedures were repeated, and the change in surface roughness was evaluated. 3D images were also overlapped, and the volumetric loss was calculated with the relevant inspector software. The data obtained were analyzed by two-way ANOVA (p < 0.05). Result: The results showed significant statistical differences for both parameters (p > 0.05). The highest volumetric loss was found in the GV group while the lowest volumetric loss was in the VE group. The highest surface roughness values were observed in the GV group, while the lowest values belonged to the VE one. Conclusion: Of the restorative materials evaluated, the VE group is suitable for long-term restorations, whereas the GV one is suitable for medium-term restorations. It is promising in terms of 3D printing technologies that the 3D material gives comparable results with the GV group. Clinical i̇mplication: Additive manufacturing techniques are a successful method that accelerates the manufacturing process. Permanent crown resins are promising alternatives to conventional production.

An evaluation of the stress effect of different occlusion concepts on hybrid abutment and implant supported monolithic zirconia fixed prosthesis: A finite element analysis.

PURPOSE: The aim of this study is to evaluate the effects of canine guidance occlusion and group function occlusion on the degree of stress to the bone, implants, abutments, and crowns using finite element analysis (FEA). MATERIALS AND METHODS: This study included the implant-prosthesis system of a three-unit bridge made of monolithic zirconia and hybrid abutments. Three-dimensional (3D) models of a bone-level implant system and a titanium base abutment were created using the original implant components. Two titanium implants, measuring 4 × 11 mm each, were selected. The loads were applied in two oblique directions of 15° and 30° under two occlusal movement conditions. In the canine guidance condition, loads (100 N) were applied to the canine crown only. In the group function condition, loads were applied to all three teeth. In this loading, a force of 100 N was applied to the canine, and 200-N forces were applied to each premolar. The stress distribution among all the components of the implant-bridge system was assessed using ANSYS SpaceClaim 2020 R2 software and finite element analysis. RESULTS: Maximum stress was found in the group function occlusion. The maximum stress increased with an increase in the angle of occlusal force. CONCLUSION: The canine guidance occlusion with monolithic zirconia crown materials is promising for implant-supported prostheses in the canine and premolar areas.

Effects of Fibers on Color and Translucency Changes of Bulk-Fill and Anterior Composites after Accelerated Aging.

The aim of this study was to determine the effects of glass and polyethylene fibers on the color and translucency change of bulk-fill and anterior composites before and after artificial accelerated aging (AAA). Two types of teflon molds were used to fabricate samples which were 13 mm in diameter and, respectively, 2 mm and 4 mm in height. Polyethylene fiber (PF) and glass fiber (GF) were incorporated in the middle of the composite samples. Color and translucency changes of each composite were evaluated before and after AAA with spectrophotometer. ANOVA and Tukey's HSD post hoc statistical analysis were used at a significance level of 0.05. Before AAA (for anterior composites), there were no significant differences in L* and b* parameters among the three groups (p > 0.05); there were no significant differences in L* parameter between PF and GF groups or in TP between GF and control groups (p > 0.05) (for bulk-fill composites). After AAA, there were no significant differences in L* parameter between GF and control groups, in a* parameter between PF and control groups, in b* parameter among all groups, or in TP parameter between GF and control groups (p > 0.05). Fiber reinforcement led to color and TP change in both anterior and bulk-fill resin composites.

The effect of a diode laser and traditional irrigants on the bond strength of self-adhesive cement.

PURPOSE: The purpose of this study was to compare the effect of a diode laser and traditional irrigants on the bond strength of self-adhesive cement. MATERIALS AND METHODS: Fifty-five incisors extracted due to periodontal problems were used. All teeth were instrumented using a set of rotary root canal instruments. The post spaces were enlarged for a No.14 (diameter, 1.4 mm) Snowlight (Abrasive technology, OH, USA) glass fiber reinforced composite post with matching drill. The teeth were randomly divided into 5 experimental groups of 11 teeth each. The post spaces were treated with the followings: Group 1: 5 mL 0.9% physiological saline; Group 2: 5 mL 5.25% sodium hypochlorite; Group 3: 5 mL 17% ethylene diamine tetra acetic acid (EDTA), Group 4: 37% orthophosphoric acid and Group 5: Photodynamic diode laser irradiation for 1 minute after application of light-active dye solution. Snowlight posts were luted with self-adhesive resin cement. Each root was sectioned perpendicular to its long axis to create 1 mm thick specimens. The push-out bond strength test method was used to measure bond strength. One tooth from each group was processed for scanning electron microscopic analysis. RESULTS: BOND STRENGTH VALUES WERE AS FOLLOW: Group 1 = 4.15 MPa; Group 2 = 3.00 MPa; Group 3 = 4.45 MPa; Group 4 = 6.96 MPa; and Group 5 = 8.93 MPa. These values were analysed using one-way ANOVA and Tukey honestly significant difference test (P<.05). Significantly higher bond strength values were obtained with the diode laser and orthophosphoric acid (P<.05). There were no differences found between the other groups (P>.05). CONCLUSION: Orthophosphoric acid and EDTA were more effective methods for removing the smear layer than the diode laser. However, the diode laser and orthophosphoric acid were more effective at the cement dentin interface than the EDTA, Therefore, modifying the smear layer may be more effective when a self-adhesive system is used.

The effect of repeated porcelain firings on corrosion resistance of different dental alloys.

PURPOSE: The aim of this study was to evaluate the effects of repeated porcelain firing process on the corrosion rates of the dental alloys. MATERIALS AND METHODS: Cr-Co, Cr-Ni and Pd-Ag alloys were used for this study. Each metal supported porcelain consisted of 30 specimens of 10 for 7, 9 and 11 firing each. Disc-shaped specimens 10 mm diameter and 3 mm thickness were formed by melting alloys with a propane-oxygen flame and casted with a centrifuge casting machine and then with the porcelain veneer fired onto the metal alloys. Corrosion tests were performed in quintuplicate for each alloy (after repeated porcelain firing) in Fusayama artificial saliva solution (pH = 5) in a low thermal-expansion borosilicate glass cell. Tamhane and Sheffe test was used to compare corrosion differences in the results after repeated firings and among 7, 9 and 11 firing for each alloy. The probability level for statistical significance was set at α=0.05. RESULTS: The corrosion resistance was higher (30 mV), in case of 7 times firing (Commercial). On the other hand, it was lower in case of 11 times firing (5 mV) (P<.05). CONCLUSION: Repeated firings decreased corrosion resistance of Pd-Ag, Cr-Co and Cr-Ni alloys. The Pd-Ag alloy exhibited little corrosion in in vitro tests. The Cr-Ni alloy exhibited higher corrosion resistance than Cr-Co alloys in in vitro tests.

Effects of different surface treatments on shear bond strength in two different ceramic systems.

The purpose of this study was to evaluate the influence of different surface treatments (sandblasting, acid etching, and laser irradiation) on the shear bond strength of lithium disilicate-based core (IPS Empress 2) and feldspathic ceramics (VITA VM 9). One hundred ceramic discs were divided into two groups of 50 discs each for two ceramic systems: IPS Empress 2 (group I) and VITA VM 9 (group II). Each of the two groups was further divided into five surface treatment groups (ten each) as follows: group SB, sandblasting with alumina particles (50 µm); group HF, 5 % hydrofluoric acid etching; group L, Er:YAG laser irradiation (distance, 1 mm; 500 mJ; 20 Hz; 10 W; manually, noncontact R14 handpiece); group SB-L, sandblasting + Er:YAG laser; and group HF-L, 5 % hydrofluoric acid + Er:YAG laser. Luting cement (Panavia 2.0) was bonded to the ceramic specimens using Teflon tubes. After 24 h of water storage, a shear bond strength test was performed using a universal testing machine at a crosshead speed of 0.5 mm/min. The data were analyzed with a two-way analysis of variance (ANOVA) and Tukey's honestly significant difference tests (α = 0.05). The two-way ANOVA indicated that the shear bond strength was significantly affected by the surface treatment methods (p < 0.05), but there was no significant interaction between the ceramic systems. Group SB-L had the highest mean values for each ceramic system. Sandblasting, followed by Er:YAG laser irradiation, enhanced the bond strength, indicating its potential use as an alternative method. The atomic force microscopic evaluation revealed that group SB had the most distinct sharp peaks among the groups.

The effect of luting cement thicknesses on the push-out bond strength of the fiber posts.

OBJECTIVE: The aim of this study was to evaluate the effect of luting cement thicknesses on the push-out bond strength of the fiber posts. MATERIALS AND METHODS: Sixty human maxillary canine teeth were endodontically treated. Post spaces were prepared and root specimens randomly divided into three groups: Group 1: etch-and-rinse (Variolink II/Exite DSC), Group 2: self-etch (Panavia F2.0/ED primer) and Group 3: self-adhesive (Clearfil SA Cement). Then each group was divided into four sub-groups according to the cement thickness, as follows: Sub-group 1: 0.35 mm, Sub-group 2: 0.25 mm, Sub-group 3: 0.15 mm, and Sub-group 4: 0.05 mm. Three slices of 1 mm thickness were obtained from each root specimen (n = 15). Push-out tests were performed and data was analyzed with two-way ANOVA and Tukey tests. RESULTS: The etch-and-rinse system (Variolink II) had a significantly higher bond strength compared with the other systems (p < 0.05). The thickest cement group (0.35 mm) had a significantly lower bond strength compared with the 0.15 and 0.05 mm groups in the etch-and-rinse and self-adhesive groups (p < 0.05). In the self-etch group, the cement thicknesses did not significantly affect the bond strength (p > 0.05). CONCLUSIONS: The etch-and-rinse system offered better bonding to root dentine than the self-adhesive and self-etch systems. The increases in cement thickness significantly reduced the bond strength of fiber posts to root dentine for both the etch-and-rinse and self-adhesive systems.

Influence of eugenol on the push-out bond strengths of fiber posts cemented with different types of resin luting agents.

This study evaluated the influence of eugenol on the push-out bond strengths of fiber posts cemented with different types of resin luting agents. Seventy-two extracted maxillary single-rooted canine teeth were randomly divided into two groups of 36 teeth. Group 1, the control group, was filled with gutta-percha only (i.e., did not receive eugenol), whereas group 2 was filled with a eugenol-containing sealer. All root canals were filled and each group was divided into three subgroups. The posts in each subgroup were cemented with the following materials: subgroup 1 with a 2-step self-etching adhesive system (Clearfil Liner Bond 2V + Panavia F); subgroup 2 with a 1-step self-etching adhesive (Panavia F); and subgroup 3 with a self-adhesive (Clearfil SA Cement). Dislodgement resistance was measured using a universal testing machine. All data were subjected to ANOVA using a factorial design and Tukey test (α = 0.05). The use of the eugenol-containing sealer significantly reduced the push-out bond strength of the fiber post (P < 0.05). The push-out bond strength of Panavia F was significantly higher than those of the other groups filled with the eugenol-containing sealer (P < 0.05). The Panavia F group was less susceptible to the inhibiting effect of eugenol than were the other evaluated groups when the fiber post was cemented in the canals filled with the eugenol-containing sealer.

The effect of post surface treatments on the bond strength of fiber posts to root surfaces.

The aim of the present study was to evaluate the influence of post surface treatment methods on the push-out bond strength of adhesively luted quartz fiber posts. Thirty freshly extracted and endodontically treated human incisor teeth were prepared for quartz fiber posts. The posts were submitted to three different surface treatments (n = 10), including no treatment, 50-µm aluminum-oxide (Al(2)O(3)) airborne-particle abrasion and Er:YAG laser (10 Hz, 150 mJ) irradiation. The posts were luted with resin cement. Each root was sectioned perpendicularly to its long axis to create specimens of 1-mm thickness. After the specimens were stored in distilled water at 37°C for 24 h, their push-out bond strength was tested using a universal testing machine at a crosshead speed of 1 mm/min. The data were analyzed by two-way ANOVA (α = .05). The two-way ANOVA indicated that push-out test values did not vary significantly according to surface treatments applied (control, airborne particle abrasion, Er:YAG laser irradiation) (p > 0.05), however, values varied according to the root segments (cervical, middle, and apical) (p < 0.01). The push-out bond strength values of the coronal root sections were the highest (p < 0.05) and there were no significant differences between the middle and apical root sections in push-out bond strength of fiber posts (p > 0.05). Air-borne particle abrasion or Er:YAG laser irradiation applied on the quartz fiber posts did not affect the push-out bond strengths relative to the root surfaces. The highest bond strength was observed in the cervical third of the roots in all groups.

Inadequate shear bond strengths of self-etch, self-adhesive systems for secure orthodontic bonding.

This study evaluated the shear bond strength (SBS) of a traditional orthodontic bracket bonding agent (Transbond XT) against two self-etch, self-adhesive systems (Maxcem Elite and Vertise Flow). Sixty premolar teeth and sixty brackets were randomly and equally divided into five groups: Transbond XT (TXT) as the control, Maxcem Elite (ME) without etching, ME with etching (ME/ Etch), Vertise Flow (VF) without etching, and VF with etching (VF/Etch). Respective SBS results of the five groups were 9.86±3.20, 4.67±2.94, 7.82±2.56, 2.55±0.77, and 7.89±1.17 MPa. SBS values of the new self-etch adhesive systems were significantly lower than the traditional etch-and-rinse control (p<0.005). However, no significant differences were found between TXT and the self-adhesives applied with etching (p>0.005). After debonding, ARI scores "0" and "1" were predominant in non-etched ME and VF groups. It was concluded that new self-etch, self-adhesive bonding systems require additional phosphoric acid application to achieve comparable SBS values as the traditional orthodontic bonding agent.

Effect of different provisional cement remnant cleaning procedures including Er:YAG laser on shear bond strength of ceramics.

PURPOSE: The purpose of this study was to evaluate the effect of provisional cement removal by different dentin cleaning protocols (dental explorer, pumice, cleaning bur, Er:YAG laser) on the shear bond strength between ceramic and dentin. MATERIALS AND METHODS: In total, 36 caries-free unrestored human third molars were selected as tooth specimens. Provisional restorations were fabricated and cemented with eugenol-free provisional cement. Then, disc-shaped ceramic specimens were fabricated and randomly assigned to four groups of dentin cleaning protocols (n = 9). Group 1 (control): Provisional cements were mechanically removed with a dental explorer. Group 2: The dentin surfaces were treated with a cleaning brush with pumice Group 3: The dentin surfaces were treated with a cleaning bur. Group 4: The provisional cements were removed by an Er:YAG laser. Self-adhesive luting cement was used to bond ceramic discs to dentin surfaces. Shear bond strength (SBS) was measured using a universal testing machine at a 0.05 mm/min crosshead speed. The data were analyzed using a Kolmogorov Smirnov, One-way ANOVA and Tukey HSD tests to perform multiple comparisons (α=0.05). RESULTS: THE DENTIN CLEANING METHODS DID NOT SIGNIFICANTLY AFFECT THE SBS OF CERAMIC DISCS TO DENTIN AS FOLLOWS: dental explorer, pumice, cleaning bur, and Er:YAG laser. CONCLUSION: The use of different cleaning protocols did not affect the SBS between dentin and ceramic surfaces.

Effects of fibers on the color change and stability of resin composites after accelerated aging.

Composite resins were reinforced with glass and polyethylene fibers in this study, and the effect of fiber reinforcement on the color change of composite resins was investigated. After accelerated aging, the effect of fiber reinforcement on the color stability of composite resins was also examined. There were three experimental groups (n=12 disks per group): non-fiber-reinforced composite (non-FRC control), polyethylene fiber (Ribbond-THM)-reinforced composite, and glass fiber (everstick NET)-reinforced composite. According to the critical remarks of color change of National Bureau of Standarts (NSB), glass fiber-reinforced anterior composites showed trace color change and polyethylene-fiber reinforced composites showed slight color change before accelerated aging. After accelerated aging, both control and fiber-reinforced composite groups showed noticeable color change. It was concluded that both the types of fiber reinforcement and composite resin influenced the color change of fiber-reinforced composite resins.

Effect of different palatal vault shapes on the dimensional stability of glass fiber-reinforced heat-polymerized acrylic resin denture base material.

OBJECTIVE: The aim of this study was to determine the effect of different palatal vault shapes on the dimensional stability of a glass fiber reinforced heat polymerized acrylic resin denture base material. METHODS: Three edentulous maxilla with shallow, deep and medium shaped palatal vaults were selected and elastomeric impressions were obtained. A maxillary cast with four reference points (A, B, C, and D) was prepared to serve as control. Point (A) was marked in the anterior midline of the edentulous ridge in the incisive papillary region, points (B) and (C) were marked in the right and left posterior midlines of the edentulous ridge in the second molar regions, and point (D) was marked in the posterior palatal midline near the fovea palatina media (Figure 2). To determine linear dimensional changes, distances between four reference points (A-B, A-C, A-D and B-C) were initially measured with a metal gauge accurate within 0.1 mm under a binocular stereo light microscope and data (mm) were recorded. RESULTS: No significant difference of interfacial distance was found in sagittal and frontal sections measured 24 h after polymerization and after 30 days of water storage in any of experimental groups (P>.05). Significant difference of linear dimension were found in all experimental groups (P<.01) between measurements made 24 h after polymerization of specimens and 30 days after water storage. CONCLUSION: Palatal vault shape and fiber impregnation into the acrylic resin bases did not affect the magnitude of interfacial gaps between the bases and the stone cast surfaces.

Effects of current provisional restoration materials on the viability of fibroblasts.

OBJECTIVES: The aim of the present study was to evaluate the cytotoxic effects of three different provisional restoration materials on fibroblasts. Two bis-acrylic based [Tempofit Duomix (Detax), Protemp 3 Garant (3M ESPE)] and one urethan dimethacrylate [Revotek LC (GC Corporation)] based provisional restoration materials used. METHODS: Materials were prepared according to the manufacturers' instructions in standard teflon disks (2x5 mm) and four samples were extracted in 7 ml of Basal Medium Eagle with 10% new born calf serum and 100 mg/ml penicillin/streptomycin for 24 hours. The L929 fibroblast cells were plated (25.000 cells/ml) in well plates, and maintained in a CO(2) incubator at 37 degrees C for 24h. After 24 hours, the incubation medium was replaced by the immersed medium in which the samples were stored and the L929 fibroblasts were incubated in contact with eluates for 24 hours at 37 degrees C for 24h. The fibroblast cell viability was analyzed by measuring the mitochondrial activity with the methyltetrazolium test (MTT). Twelve well used for each specimen and experiment repeated for two times. The data was statistically analyzed by Mann-Whitney U tests. RESULTS: The results showed that, Revotek LC and Protemp 3 Garant were not cytotoxic for fibroblast cells when compared to control group (P>.05). However, Tempofit duomix was cytotoxic for L929 fibroblasts when compared to control group and other tested materials (P<.05). CONCLUSIONS: Taking into consideration the limitations of an in vitro study, our study indicate that provisional restoration materials might have cytotoxic effects on fibroblasts and should be selected carefully for clinical applications.