Elucidating the relationship between PFOA and PFOS destruction, particle size and electron generation in amended media commonly found in soils.

Ball milling has emerged as a promising destructive technique for treating per- and polyfluoroalkyl substances (PFAS)-impacted soils. Environmental media properties such as reactive species generated upon ball milling and particle size are postulated to influence the effectiveness of the technology. In this study, four media types amended with perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were planetary ball milled to investigate destruction, fluoride recovery without additional co-milling reagents and the relationship between PFOA and PFOS destruction, particle size during milling, and electron generation. Silica sand, nepheline syenite sand, calcite and marble were sieved to achieve similar initial particle sizes (6/35 distribution), amended with PFOA and PFOS, and milled for 4 h. Particle size analysis was conducted throughout milling and 2,2-diphenyl-1-picrylhydrazyl (DPPH•) was used as a radical scavenger to assess electron generation from the four media types. Particle size reduction was observed to be positively correlated to PFOA and PFOS destruction and DPPH• neutralization (demonstrating electron generation by milling) in silica sand and nepheline syenite sand. Milling of a fine fraction (< 500 µm) of silica sand revealed less destruction compared to the 6/35 distribution suggesting the ability to fracture grains in silicate media is integral to PFOA and PFOS destruction. DPPH• neutralization was demonstrated in all four amended media types, confirming silicate sands and calcium carbonates generate electrons as a reactive species during ball milling. Fluoride loss as a function of milling time was observed in all amended media types. A sodium fluoride (NaF) spiked was used to quantify fluoride loss in the media independent of PFAS. A method was developed using the NaF-amended media fluoride concentrations to estimate the total fluorine liberated from PFOA and PFOS by ball milling. Estimates produced suggest complete recovery of theoretical fluorine yield is obtained. Data from this study was used to propose a reductive destruction mechanism for PFOA and PFOS.

Use of a horizontal ball mill to remediate per- and polyfluoroalkyl substances in soil.

There is a need for destructive technologies for per- and polyfluoroalkyl substances (PFAS) in soil. While planetary ball mill have been shown successful degradation of PFAS, there are issues surrounding scale up (maximum size is typically 0.5 L cylinders). While having lower energy outputs, horizontal ball mills, for which scale up is not a limiting factor, already exist at commercial/industrial sizes from the mining, metallurgic and agricultural industries, which could be re-purposed. This study evaluated the effectiveness of horizontal ball mills in degrading perfluorooctanesulfonate (PFOS), 6:2 fluorotelomer sulfonate (6:2 FTSA), and aqueous film forming foam (AFFF) spiked on nepheline syenite sand. Horizontal ball milling was also applied to two different soil types (sand dominant and clay dominant) collected from a firefighting training area (FFTA). Liquid chromatography tandem mass spectrometry was used to track 21 target PFAS throughout the milling process. High-resolution accurate mass spectrometry was also used to identify the presence and degradation of 19 non-target fluorotelomer substances, including 6:2 fluorotelomer sulfonamido betaine (FtSaB), 7:3 fluorotelomer betaine (FtB), and 6:2 fluorotelomer thioether amido sulfonate (FtTAoS). In the presence of potassium hydroxide (KOH), used as a co-milling reagent, PFOS, 6:2 FTSA, and the non-target fluorotelomer substances in the AFFF were found to undergo upwards of 81%, 97%, and 100% degradation, respectively. Despite the inherent added complexity associated with field soils, better PFAS degradation was observed on the FFTA soils over the spiked NSS, and more specifically, on the FFTA clay over the FFTA sand. These results held through scale-up, going from the 1 L to the 25 L cylinders. The results of this study support further scale-up in preparation for on-site pilot tests.

Mechanochemical remediation of perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) amended sand and aqueous film-forming foam (AFFF) impacted soil by planetary ball milling.

Per- and polyfluoroalkyl substances (PFAS) are manmade, fluorinated organic chemicals which have been identified as persistent organic pollutants. PFAS have surface active properties that have made them suitable for applications in oil- and water-resistant products, as well as many firefighting foams. No on-site remediation strategies exist to treat PFAS impacted soils. Mechanochemical remediation of PFOS- and PFOA-amended sand via a planetary ball mill was studied. The effect of sand mass, KOH as a co-milling reagent, and water saturation on the degradation of PFOA and PFOS was evaluated. By 4 h of milling concentrations were reduced by up to 98% for PFOS-amended dry sand and 99% for PFOA-amended dry sand without the addition of a co-milling reagent. Water saturation was determined to be a significant hindrance on the mechanochemical destruction of PFOS and PFOA. A maximum of 89% of fluoride was recovered from PFOS-amended sand when KOH was used as a co-milling reagent. It is hypothesized that reactive particles generated from the fracture of sand grains react with PFAS molecules to initiate destruction, which can result in full defluorination. Milling experiments were also conducted on soils from a Canadian firefighting training area (FFTA), demonstrating that PFOS concentrations can be reduced by up to 96% in site soils. For the first time, ball milling for the remediation of PFAS in environmental media has been demonstrated using amended sand and legacy soils from a FFTA.