Microstructural and Textural Investigation of an Mg-Zn-Al-Ca Alloy after Hot Plane Strain Compression.

The formability of magnesium alloys can be significantly improved by Ca as an alloying addition. Compared to conventional alloy sheets such as AZ31, texture modification can be found in rolled Mg-Ca sheets, which reveal a randomized orientation distribution. The hot deformation behavior of a twin-roll cast and homogenized Mg-2Zn-1Al-0.3Ca (ZAX210) alloy was characterized during hot compression at a temperature of 350 °C and strain rates of 0.1 s-1 and 10 s-1. Electron backscatter diffraction (EBSD) analysis was performed in order to describe the microstructural and texture evolution. The ZAX210 alloy exhibits a pronounced dynamic recrystallization (DRX) behavior during compression at high strain rates, while at lower strain rates DRX hardly occurred. This effect can be attributed to different DRX mechanisms that take place as a function of strain rate. At low strain rates, DRX occurred locally at the grain boundaries of the original microstructure, forming a so-called necklace structure. Increasing strain rate results in an increased fraction of recrystallized grains from 18% (0.1 s-1) to 39% (10 s-1). The microstructure revealed that twin boundaries act as nucleation sites for the DRX (TDRX). The recrystallized areas exhibit a weaker texture compared to the deformed microstructure.

Orthotropic Behavior of Twin-Roll-Cast and Hot-Rolled Magnesium ZAX210 Sheet.

Magnesium sheet metal alloys offer a deformation asymmetry, which is strongly related to grain size and texture. In order to predict deformation behavior as well as to provide methods to eliminate anisotropy and yield asymmetry, a lot of effort is invested in studying the tension-compression asymmetry of magnesium alloys. However, only a few studies deal with the characterization of the yield asymmetry of magnesium wrought alloys, especially Ca-containing alloys, related to temperature and strain. In this study, the orthotropic behavior of a twin-roll-cast, homogenized, rolled and finish-annealed Mg-2Zn-1Al-0.3Ca (ZAX210) magnesium alloy was investigated by tensile testing at room temperature, 150 °C and 250 °C. The r-values were determined and the Hill'48 yield criterion was used for the constitutive formulation of the plastic yielding and deformation. The yield loci calculated using Mises and Hill'48 as well as the determined r-values reveal an almost isotropic behavior of the ZAX210 alloy. The r-value increases with increasing logarithmic strain. At 0.16 logarithmic strain the r-values at room temperature vary between 1 (0°) and 1.5 (45° and 90°). At higher temperatures (250 °C), r-values close to 1 at all tested directions are attained. The enhanced yield asymmetry can be attributed to the weaker basal texture that arises during hot rolling and final annealing of the twin-roll-cast ZAX210 magnesium alloy. In comparison to AZ31, the ZAX210 alloy shows a yield behavior close to transversal isotropy. Finally, responsible mechanisms for this behavior are discussed.

A Comparative Study on the Hot Deformation Behavior of As-Cast and Twin-Roll Cast Mg-6.8Y-2.5Zn-0.4Zr Alloy.

The Mg-6.8Y-2.5Zn-0.4Zr (WZ73) alloy exhibits different microstructure characteristic after conventional casting compared to the twin-roll cast (TRC) state. Twin-roll casting results in a finer microstructure, where the LPSO phases are more finely distributed and less strongly connected. A transfer of the hot deformation behavior from the as-cast condition to the TRC condition is only possible to a limited extent due to the microstructural differences. Both states show differences in the recrystallization behavior during hot deformation. In the conventional cast state, dynamic recrystallization (DRX) is assumed to be delayed by the occurrence of coarse blocky LPSO phases. Main DRX mechanisms are continuous dynamic recrystallization (CDRX), particle stimulated nucleation (PSN) and twin induced dynamic recrystallization (TDRX). The deformed TRC sample showed pronounced DRX at almost all deformation conditions. Besides the TDRX and the PSN mechanism, kink induced dynamic recrystallization (KDRX) can be observed. Optimum deformation conditions for both states are temperatures from 500 °C to 520 °C, and strain rates ranging from 0.01 s-1 to 0.1 s-1 for the as-cast material as well as a strain rate of 1 s-1 for the TRC material.

Hot Deformation and Dynamic Recrystallisation Behaviour of Twin-Roll Cast Mg-6.8Y-2.5Zn-0.4Zr Magnesium Alloy.

In this work, the deformation behaviour of a twin-roll cast (TRC) Mg-6.8Y-2.5Zn-0.4Zr alloy during plane strain compression was characterised by high-temperature testing. Based on the experimental data, the values of strain-rate sensitivity, the efficiency of power dissipation and the instability parameter were investigated under the conditions of various hot deformation parameters. In contrast to conventionally cast material, no lamellae of the LPSO (long period stacking ordered) phase were precipitated in the magnesium matrix after TRC. The precipitation of fine lamellar LPSO phases only occurred during cooling to forming temperature after the heat treatment. Dynamic recrystallization (DRX) hardly occurred during deformation at temperatures between 350 °C and 400 °C. This can be attributed to the precipitation of the lamellar LSPO phases, which contribute to retardation of the DRX process. At higher deformation temperatures and strain rates DRX is pronounced and the twin-induced (TRDX) as well as continuous dynamic recrystallization could be identified as the dominant softening mechanisms. The processing maps were established by superimposing the instability map over the power dissipation map, this being associated with microstructural evolution analysis in the hot deformation processes. Two instability zones could be recognised for the twin-roll cast and heat-treated Mg-6.8Y-2.5Zn-0.4Zr alloy: (1) 350 °C to 460 °C and 0.01 s-1 to 0.3 s-1 and (2) 485 °C to 525 °C and 2.5 s-1 to 10 s-1, where deformation is not favourable.

Microstructure and Hot Deformation Behavior of Twin Roll Cast Mg-2Zn-1Al-0.3Ca Alloy.

In the present work, the microstructure, texture, mechanical properties as well as hot deformation behavior of a Mg-2Zn-1Al-0.3Ca sheet manufactured by twin roll casting were investigated. The twin roll cast state reveals a dendritic microstructure with intermetallic compounds predominantly located in the interdendritic areas. The twin roll cast samples were annealed at 420 °C for 2 h followed by plane strain compression tests in order to study the hardening and softening behavior. Annealing treatment leads to the formation of a grain structure, consisting of equiaxed grains with an average diameter of approximately 19 µm. The twin roll cast state reveals a typical basal texture and the annealed state shows a weakened texture, by spreading basal poles along the transverse direction. The twin roll cast Mg-2Zn-1Al-0.3Ca alloy offers a good ultimate tensile strength of 240 MPa. The course of the flow curves indicate that dynamic recrystallization occurs during hot deformation. For the validity range from 250 °C to 450 °C as well as equivalent logarithmic strain rates from 0.01 s-1 to 10 s-1 calculated model coefficients are shown. The average activation energy for plastic flow of the twin roll cast and annealed Mg-2Zn-1Al-0.3Ca alloy amounts to 180.5 kJ/mol. The processing map reveals one domain with flow instability at temperatures above 370 °C and strain rates ranging from 3 s-1 to 10 s-1. Under these forming conditions, intergranular cracks arose and grew along the grain boundaries.