3D printing of ferromagnetic passive shims for field shaping in magnetic resonance imaging.

Magnetic Resonance Imaging (MRI) often encounters image quality degradation due to magnetic field inhomogeneities. Conventional passive shimming techniques involve the manual placement of discrete magnetic materials, imposing limitations on correcting complex inhomogeneities. To overcome this, we propose a novel 3D printing method utilizing binder jetting technology to enable precise deposition of a continuous range of concentrations of ferromagnetic ink. This approach grants complete control of the magnitude of the magnetic moment within the passive shim enabling tailored corrections of B0 field inhomogeneities. By optimizing the magnetic field distribution using linear programming and an in-house written Computer-Aided Design (CAD) generation software, we printed shims with promising results in generating low spherical harmonic corrections. Experimental evaluations demonstrate feasibility of these 3D printed passive shims to induce target magnetic fields corresponding to second-order spherical harmonic, as evidenced by acquired B0 maps. The electrically insulating properties of the printed shims eliminate the risk of eddy currents and heating, thus ensuring safety. The dimensional fabrication accuracy of the printed shims surpasses previous methods, enabling more precise and localized correction of subject-specific inhomogeneities. The findings highlight the potential of binder-jetted 3D printed passive shims in MRI shimming as a versatile and efficient solution for fabricating passive shims, with the potential to enhance the quality of MRI imaging while also being applicable to other types of Magnetic Resonance systems.

Label-Free Iron Oxide Nanoparticles as Multimodal Contrast Agents in Cells Using Multi-Photon and Magnetic Resonance Imaging.

INTRODUCTION: The inherent fluorescence properties of iron oxide nanoparticles (IONPs) were characterized, and their applicability for multiphoton imaging in cells was tested in combination with their magnetic resonance imaging (MRI) capabilities. METHODS: Superparamagnetic iron oxide nanoparticles were synthesized and subsequently coated with polyethylene glycol to make them water-dispersible. Further characterization of the particles was performed using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), dynamic light scattering (DLS), superconducting quantum interference device (SQUID) and magnetic resonance relaxivity measurements. MRI and fluorescence properties of bare IONPs were first studied in solution and subsequently in A549-labeled cells. RESULTS: The particles, with a core size of 11.3 ± 4.5 nm, showed a good negative MRI contrast in tissue-mimicking phantoms. In vitro studies in mammalian A549 cells demonstrate that these IONPs are biocompatible and can also produce significant T2/T2* contrast enhancement in IONPs-labeled cells. Furthermore, excitation-wavelength dependent photoluminescence was observed under one- and two-photon excitation. DISCUSSION: The obtained results indicated that IONPs could be used for fluorescence label-free bioimaging at multiple wavelengths, which was proven by multiphoton imaging of IONPs internalization in A549 cancer cells.

Identifying Native Point Defects in the Topological Insulator Bi2Te3.

We successfully identified native point defects that occur in Bi2Te3 crystals by combining high-resolution bias-dependent scanning tunneling microscopy and density functional theory based calculations. As-grown Bi2Te3 crystals contain vacancies, antisites, and interstitial defects that may result in bulk conductivity and therefore may change the insulating bulk character. Here, we demonstrate the interplay between the growth conditions and the density of different types of native near-surface defects. In particular, scanning tunneling spectroscopy reveals the dependence on not only the local atomic environment but also on the growth kinetics and the resulting sample doping from n-type toward intrinsic crystals with the Fermi level positioned inside the energy gap. Our results establish a bias-dependent STM signature of the Bi2Te3 native defects and shed light on the link between the native defects and the electronic properties of Bi2Te3, which is relevant for the synthesis of topological insulator materials and the related functional properties.

The influence of phonon softening on the superconducting critical temperature of Sn nanostructures.

The increase in superconducting transition temperature (TC) of Sn nanostructures in comparison to bulk, was studied. Changes in the phonon density of states (PDOS) of the weakly coupled superconductor Sn were analyzed and correlated with the increase in TC measured by magnetometry. The PDOS of all nanostructured samples shows a slightly increased number of low-energy phonon modes and a strong decrease in the number of high-energy phonon modes in comparison to the bulk Sn PDOS. The phonon densities of states, which were determined previously using nuclear resonant inelastic X-ray scattering, were used to calculate the superconducting transition temperature using the Allen-Dynes-McMillan (ADMM) formalism. Both the calculated as well as the experimentally determined values of TC show an increase compared to the bulk superconducting transition temperature. The good agreement between these values indicates that phonon softening has a major influence on the superconducting transition temperature of Sn nanostructures. The influence of electron confinement effects appears to be minor in these systems.

Enhanced Magnetoelectric Coupling in BaTiO3-BiFeO3 Multilayers-An Interface Effect.

Combining various (multi-)ferroic materials into heterostructures is a promising route to enhance their inherent properties, such as the magnetoelectric coupling in BiFeO3 thin films. We have previously reported on the up-to-tenfold increase of the magnetoelectric voltage coefficient α ME in BaTiO3-BiFeO3 multilayers relative to BiFeO3 single layers. Unraveling the origin and mechanism of this enhanced effect is a prerequisite to designing new materials for the application of magnetoelectric devices. By careful variations in the multilayer design we now present an evaluation of the influences of the BaTiO3-BiFeO3 thickness ratio, oxygen pressure during deposition, and double layer thickness. Our findings suggest an interface driven effect at the core of the magnetoelectric coupling effect in our multilayers superimposed on the inherent magnetoelectric coupling of BiFeO3 thin films, which leads to a giant α ME coefficient of 480 V c m -1 Oe-1 for a 16 × (BaTiO3-BiFeO3) superlattice with a 4 . 8 nm double layer periodicity.

Tailored Ag-Cu-Mg multielemental nanoparticles for wide-spectrum antibacterial coating.

Bactericidal nanoparticle coatings are very promising for hindering the indirect transmission of pathogens through cross-contaminated surfaces. The challenge, limiting their employment in nosocomial environments, is the ability of tailoring the coating's physicochemical properties, namely, composition, cytotoxicity, bactericidal spectrum, adhesion to the substrate, and consequent nanoparticles release into the environment. We have engineered a new family of nanoparticle-based bactericidal coatings comprising Ag, Cu, and Mg and synthesized by a green gas-phase technique. These coatings present wide-spectrum bactericidal activity on both Gram-positive and Gram-negative reference strains and tunable physicochemical properties of relevance in view of their "on-field" deployment. The link between material and functional properties is rationalized based on a multidisciplinary and multitechnique approach. Our results pave the way for engineering biofunctional, fully tunable nanoparticle coatings, exploiting an arbitrarily wide number of elements in a straightforward, eco-friendly, high-throughput, one-step process.

Magnetic orders and origin of exchange bias in Co clusters embedded oxide nanocomposite films.

Magnetic nanoparticles embedded oxide semiconductors are interesting candidates for spintronics in view of combining ferromagnetic (FM) and semiconducting properties. In this work, Co-ZnO and Co-V2O3 nanocomposite thin films are synthesized by Co ion implantation in crystalline thin films. Magnetic orders vary with the implantation fluence in Co-ZnO, where superparamagnetic (SPM) order appears in the low-fluence films (2 × 1016 and 4 × 1016 ions cm-2) and FM order co-exists with the SPM phase in high-fluence films (1 × 1017 ions cm-2). Exchange bias (EB) appears in the high-fluence films, with an EB field of about 100 Oe at 2 K and a blocking temperature of around 100 K. On the other hand, Co-V2O3 thin films with an implantation fluence of 3.5 × 1016 ions cm-2 exhibit a clear antiferromagnetic (AFM) coupling at low temperatures without the EB effect. The different magnetic behavior of the Co-implanted films with different Co content leads us to conclude that the observed EB effect in the Co-ZnO films results from the FM/AFM coupling between sizable Co nanoparticles and their CoO/Co3O4 surroundings in the (Zn,Co)O matrix. On the other hand, the absence of EB effect in Co-V2O3 appears to be due to the small size of the FM Co nanoparticles in spite of an AFM magnetic order. Detailed studies of magnetic orders and EB effect in magnetic nanocomposite semiconductors can pave the way for their application in spintronics.

Photoacoustic Sensing of Trapped Fluids in Nanoporous Thin Films: Device Engineering and Sensing Scheme.

Accessing fluid infiltration in nanogranular coatings is an outstanding challenge, of relevance for applications ranging from nanomedicine to catalysis. A sensing platform, allowing quantifying the amount of fluid infiltrated in a nanogranular ultrathin coating, with thickness in the 10-40 nm range, is here proposed and theoretically investigated by multiscale modeling. The scheme relies on impulsive photoacoustic excitation of hypersonic mechanical breathing modes in engineered gas-phase-synthesized nanogranular metallic ultrathin films and time-resolved acousto-optical read-out of the breathing modes frequency shift upon liquid infiltration. A superior sensitivity, exceeding 26 × 103 cm2/g, is predicted upon equivalent areal mass loading of a few ng/mm2. The capability of the present scheme to discriminate among different infiltration patterns is discussed. The platform is an ideal tool to investigate nanofluidics in granular materials and naturally serves as a distributed nanogetter coating, integrating fluid sensing capabilities. The proposed scheme is readily extendable to other nanoscale and mesoscale porous materials.

Impact of magnetization and hyperfine field distribution on high magnetoelectric coupling strength in BaTiO3-BiFeO3 multilayers.

Correlations were established between the hyperfine field distribution around the Fe atoms, the multiferroic properties, and the high magnetoelectric coefficient in BaTiO3-BiFeO3 multilayer stacks with variable BiFeO3 single layer thickness, down to 5 nm. Of key importance in this study was the deposition of 57Fe - enriched BiFeO3, which enhances the sensitivity of conversion electron Mössbauer spectroscopy by orders of magnitude. The magnetoelectric coefficient αME reaches a maximum of 60.2 V cm-1 Oe-1 at 300 K and at a DC bias field of 2 Tesla for a sample of 15 × (10 nm BaTiO3-5 nm BiFeO3) and is one of the highest values reported so far. Interestingly, the highest αME is connected to a high asymmetry of the hyperfine field distribution of the multilayer composite samples. The possible mechanisms responsible for the strong magnetoelectric coupling are discussed.

Tunability of Size and Magnetic Moment of Iron Oxide Nanoparticles Synthesized by Forced Hydrolysis.

To utilize iron oxide nanoparticles in biomedical applications, a sufficient magnetic moment is crucial. Since this magnetic moment is directly proportional to the size of the superparamagnetic nanoparticles, synthesis methods of superparamagnetic iron oxide nanoparticles with tunable size are desirable. However, most existing protocols are plagued by several drawbacks. Presented here is a one-pot synthesis method resulting in monodisperse superparamagnetic iron oxide nanoparticles with a controllable size and magnetic moment using cost-effective reagents. The obtained nanoparticles were thoroughly characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) measurements. Furthermore, the influence of the size on the magnetic moment of the nanoparticles is analyzed by superconducting quantum interference device (SQUID) magnetometry. To emphasize the potential use in biomedical applications, magnetic heating experiments were performed.

Correlation of High Magnetoelectric Coupling with Oxygen Vacancy Superstructure in Epitaxial Multiferroic BaTiO3-BiFeO3 Composite Thin Films.

Epitaxial multiferroic BaTiO3-BiFeO3 composite thin films exhibit a correlation between the magnetoelectric (ME) voltage coefficient αME and the oxygen partial pressure during growth. The ME coefficient αME reaches high values up to 43 V/(cm·Oe) at 300 K and at 0.25 mbar oxygen growth pressure. The temperature dependence of αME of the composite films is opposite that of recently-reported BaTiO3-BiFeO3 superlattices, indicating that strain-mediated ME coupling alone cannot explain its origin. Probably, charge-mediated ME coupling may play a role in the composite films. Furthermore, the chemically-homogeneous composite films show an oxygen vacancy superstructure, which arises from vacancy ordering on the {111} planes of the pseudocubic BaTiO3-type structure. This work contributes to the understanding of magnetoelectric coupling as a complex and sensitive interplay of chemical, structural and geometrical issues of the BaTiO3-BiFeO3 composite system and, thus, paves the way to practical exploitation of magnetoelectric composites.

Co-Rich ZnCoO Nanoparticles Embedded in Wurtzite Zn1-xCoxO Thin Films: Possible Origin of Superconductivity.

Co-rich ZnCoO nanoparticles embedded in wurtzite Zn0.7Co0.3O thin films are grown by pulsed laser deposition on a Si substrate. Local superconductivity with an onset Tc at 5.9 K is demonstrated in the hybrid system. The unexpected superconductivity probably results from Co3+ in the Co-rich ZnCoO nanoparticles or from the interface between the Co-rich nanoparticles and the Zn0.7Co0.3O matrix.

The pH-dependent photoluminescence of colloidal CdSe/ZnS quantum dots with different organic coatings.

The photoluminescence (PL) of colloidal quantum dots (QDs) is known to be sensitive to the solution pH. In this work we investigate the role played by the organic coating in determining the pH-dependent PL. We compare two types of CdSe/ZnS QDs equipped with different organic coatings, namely dihydrolipoic acid (DHLA)-capped QDs and phospholipid micelle-encapsulated QDs. Both QD types have their PL intensity quenched at acidic pH values, but they differ in terms of the reversibility of the quenching process. For DHLA-capped QDs, the quenching is nearly irreversible, with a small reversible component visible only on short time scales. For phospholipid micelle-encapsulated QDs the quenching is notably almost fully reversible. We suggest that the surface passivation by the organic ligands is reversible for the micelle-encapsulated QDs. Additionally, both coatings display pH-dependent spectral shifts. These shifts can be explained by a combination of irreversible processes, such as photo-oxidation and acid etching, and reversible charging of the QD surface, leading to the quantum-confined Stark effect (QCSE), the extent of each effect being coating-dependent. At high ionic strengths, the aggregation of QDs also leads to a spectral (red) shift, which is attributable to the QCSE and/or electronic energy transfer.

Selective protein immobilization onto gold nanoparticles deposited under vacuum on a protein-repellent self-assembled monolayer.

The immobilization of proteins on flat substrates plays an important role for a wide spectrum of applications in the fields of biology, medicine, and biochemistry, among others. An essential prerequisite for the use of proteins (e.g., in biosensors) is the conservation of their biological activity. Losses in activity upon protein immobilization can largely be attributed to a random attachment of the proteins to the surface. In this study, we present an approach for the immobilization of proteins onto a chemically heterogeneous surface, namely a surface consisting of protein-permissive and protein-repellent areas, which allows for significant reduction of random protein attachment. As protein-permissive, i.e., as protein-binding sites, ultra pure metallic nanoparticles are deposited under vacuum onto a protein-repellent PEG-silane polymer layer. Using complementary surface characterization techniques (atomic force microscopy, quartz crystal microbalance, and X-ray photoelectron spectroscopy) we demonstrate that the Au nanoparticles remain accessible for protein attachment without compromising the protein-repellency of the PEG-silane background. Moreover, we show that the amount of immobilized protein can be controlled by tuning the Au nanoparticle coverage. This method shows potential for applications requiring the control of protein immobilization down to the single molecule level.

Temperature determination of resonantly excited plasmonic branched gold nanoparticles by X-ray absorption spectroscopy.

The fields of bioscience and nanomedicine demand precise thermometry for nanoparticle heat characterization down to the nanoscale regime. Since current methods often use indirect and less accurate techniques to determine the nanoparticle temperature, there is a pressing need for a direct and reliable element-specific method. In-situ extended X-ray absorption fine structure (EXAFS) spectroscopy is used to determine the thermo-optical properties of plasmonic branched gold nanoparticles upon resonant laser illumination. With EXAFS, the direct determination of the nanoparticle temperature increase upon laser illumination is possible via the thermal influence on the gold lattice parameters. More specifically, using the change of the Debye-Waller term representing the lattice disorder, the temperature increase is selectively measured within the plasmonic branched nanoparticles upon resonant laser illumination. In addition, the signal intensity shows that the nanoparticle concentration in the beam more than doubles during laser illumination, thereby demonstrating that photothermal heating is a dynamic process. A comparable temperature increase is measured in the nanoparticle suspension using a thermocouple. This good correspondence between the temperature at the level of the nanoparticle and at the level of the suspension points to an efficient heat transfer between the nanoparticle and the surrounding medium, thus confirming the potential of branched gold nanoparticles for hyperthermia applications. This work demonstrates that X-ray absorption spectroscopy-based nanothermometry could be a valuable tool in the fast-growing number of applications of plasmonic nanoparticles, particularly in life sciences and medicine.

Surface modification of gamma-Fe2O3@SiO2 magnetic nanoparticles for the controlled interaction with biomolecules.

Modifying the surface of magnetic nanoparticles (MNPs) to allow for controlled interaction with biomolecules enables their implementation in biomedical applications such as contrast agents for magnetic resonance imaging, labels in magnetic biosensing or media for magnetically assisted bioseparation. In this paper, self-assembly of trialkoxysilanes is used to chemically functionalize the surface of gamma-Fe2O3@SiO2 core-shell particles. First, the silane deposition procedure was optimized using infrared analysis in order to obtain maximum packing density of the silanes on the particles. The surface coverage was determined to be approximately 8 x 10(14) molecules/cm2. It was shown that the magnetic, crystalline, and morphological properties of the MNPs were not altered by deposition of a thin silane coating. The optimized procedure was transferred for the deposition of aldehyde and poly(ethylene glycol) (PEG) presenting silanes. The presence of both silanes on the particle surface was confirmed using XPS and FTIR. The interaction of proteins with silane-modified MNPs was monitored using a Bradford protein assay. Our results demonstrate that, by introducing aldehyde functions, the MNPs are capable of covalently binding human IgG while retaining their specific binding capacity. Maximum surface coverage occurs at 46 microg antibodies per mg particle, which corresponds to 35 antibodies bound to an average sized MNP (54 nm in diameter). The human IgG functionalized MNPs exhibit a high degree of specificity (approximately 90%) and retained a binding capacity of 32%. Using the same approach, streptavidin was coupled onto the MNPs and the biotin binding capacity was determined using biotinylated fluorescein. At maximum surface coverage, a biotin binding capacity of 1500 pmol/mg was obtained, corresponding to a streptavidin activity of 76%. On the other hand, by introducing PEG functions the non-specific adsorption of serum proteins could be significantly suppressed down to approximately 3 microg/mg. We conclude that self-assembly of silane films creates a generic platform for the controlled interactions of MNPs with biomolecules.

Nanoengineered magnetic-field-induced superconductivity.

The perpendicular critical fields of a superconducting film have been strongly enhanced by using a nanoengineered lattice of magnetic dots (dipoles) on top of the film. Magnetic-field-induced superconductivity is observed in these hybrid superconductor/ferromagnet systems due to the compensation of the applied field between the dots by the stray field of the dipole array. By switching between different magnetic states of the nanoengineered field compensator, the critical parameters of the superconductor can be effectively controlled.