RESUMO
Collagen fibers and their orientation greatly influence an artery's mechanical characteristics, determining its transversely isotropic behavior. It is generally assumed that these fibers are deposited along a preferred direction to maximize the load bearing capacity of the vessel wall. This implies a large spatial variation in collagen orientation which can be reconstructed in numerical models using so-called reorientation algorithms. Until now, these algorithms have used the classical continuum mechanics modeling framework which requires knowledge of tissue-level parameters and the artery's stress-free reference state, which is inaccessible in a clinical context. We present an algorithm to compute the preferred fiber distribution compatible with the constrained mixture theory, which orients two collagen fiber families according to the loading experienced by the isotropic non-collagenous extracellular matrix, without requiring prior knowledge of the stress-free state. Because consensus is lacking whether stress or stretch is the determining factor behind the preferred fiber distribution, we implemented both approaches and compared the results with experimental microstructural data of an abdominal aorta. The stress-based algorithm was able to describe several experimentally observed transitions of the fiber distribution across the intima, media and adventitia.
Assuntos
Artérias , Colágeno , Humanos , Colágeno/química , Matriz Extracelular , Aorta Abdominal , Estresse Mecânico , Fenômenos BiomecânicosRESUMO
Objectives: Rupture and dissection are feared complications of ascending thoracic aortic aneurysms caused by mechanical failure of the wall. The current method of using the aortic diameter to predict the risk of wall failure and to determine the need for surgical resection lacks accuracy. Therefore, this study aims to identify reliable and clinically measurable predictors for aneurysm rupture or dissection by performing a personalized failure risk analysis, including clinical, geometrical, histologic, and mechanical data. Methods: The study cohort consisted of 33 patients diagnosed with ascending aortic aneurysms without genetic syndromes. Uniaxial tensile tests until failure were performed to determine the wall strength. Material parameters were fitted against ex vivo planar biaxial data and in vivo pressure-diameter relationships at diastole and systole, which were derived from multiphasic computed tomography (CT) scans. Using the resulting material properties and in vivo data, the maximal in vivo stress at systole was calculated, assuming a thin-walled axisymmetric geometry. The retrospective failure risk was calculated by comparing the peak wall stress at suprasystolic pressure with the wall strength. Results: The distensibility coefficient, reflecting aortic compliance and derived from blood pressure measurements and multiphasic CT scans, outperformed predictors solely based on geometrical features in assessing the risk of aneurysm failure. Conclusions: In a clinical setting, multiphasic CT scans followed by the calculation of the distensibility coefficient are of added benefit in patient-specific, clinical decision-making. The distensibility derived from the aneurysm volume change has the best predictive power, as it also takes the axial stretch into account.
RESUMO
Planar biaxial testing is a popular experimental technique for characterizing and comparing biological soft tissues. A correct identification of the different stress states of the tissue sample is therefore essential. However, the difference between the zero-stress reference state and the sample state prior to the loading cycle caused by the mounting, preconditioning and preloading is often not considered. The importance of this difference, caused by prestretch, is investigated by simulating virtual planar biaxial experiments, either assuming an ideal test with a single deformation gradient or using finite element modeling to simulate a rake-based experiment. Multiple parameter fitting methods are used to estimate the material properties based on the available experimental data. These methods vary based on how they approximate the zero-stress state: either the prestretch is ignored, or the loads are zeroed after the preload has been reached, or the unknown prestretch values are included into the optimization function. The results reveal the high necessity of assessing the stress-free state when analyzing a planar biaxial test. The material fitting including the prestretch outperforms the other methods in terms of correctly describing the mechanical behavior of the tested material. It can be extended to correct for the boundary effects induced by the gripping mechanisms, providing a more accurate, yet more computationally expensive estimate of the material properties.
Assuntos
Estresse Mecânico , Fenômenos BiomecânicosRESUMO
Secondary mitral regurgitation occurs when a left ventricular problem causes leaking of the mitral valve. The altered left ventricular geometry changes the orientation of the subvalvular apparatus, thereby affecting the mechanical stress on the mitral valve. This in turn leads to active remodeling of the mitral valve, in order to compensate for the ventricular remodeling. In this study, a biomechanical analysis was performed on eight human mitral valves with secondary mitral regurgitation and ten healthy human mitral valves to better understand this pathophysiology and its effect on the mechanical properties of these tissues. Samples were obtained from the anterior and posterior leaflet and used for planar biaxial mechanical experiments. Uniaxial experiments were performed on four groups of mitral valve chords: anterior basal, anterior marginal, posterior basal and posterior marginal chords. The mechanical response of the mitral valve leaflets was fitted to the May-Newman and Yin constitutive model, whereas the material parameters of the third order Ogden model were determined for the chord samples. Next, stiffnesses calculated at low and high stress levels were statistically analyzed. Leaflet samples with secondary mitral regurgitation showed a small thickness increase and a change in anisotropy index compared to healthy control valves. Diseased leaflets were more compliant circumferentially and stiffer radially, resulting in anisotropic samples with the radial direction being stiffest. In addition, chord samples were slightly thicker and less stiff at high stress in secondary mitral regurgitation, when grouped per leaflet type and insertion region. These results confirm mechanical alterations due to the pathophysiological valvular changes caused by left ventricular remodeling. It is important that these changes in mechanical behavior are incorporated into computational models of the mitral valve.