Development of a hybrid wave based-transfer matrix model for sound transmission analysis.

In this paper, a hybrid wave based-transfer matrix model is presented that allows for the investigation of the sound transmission through finite multilayered structures placed between two reverberant rooms. The multilayered structure may consist of an arbitrary configuration of fluid, elastic, or poro-elastic layers. The field variables (structural displacements and sound pressures) are expanded in terms of structural and acoustic wave functions. The boundary and continuity conditions in the rooms determine the participation factors in the pressure expansions. The displacement of the multilayered structure is determined by the mechanical impedance matrix, which gives a relation between the pressures and transverse displacements at both sides of the structure. The elements of this matrix are calculated with the transfer matrix method. First, the hybrid model is numerically validated. Next a comparison is made with sound transmission loss measurements of a hollow brick wall and a sandwich panel. Finally, numerical simulations show the influence of structural damping, room dimensions and plate dimensions on the sound transmission loss of multilayered structures.

Sound transmission through finite lightweight multilayered structures with thin air layers.

The sound transmission loss (STL) of finite lightweight multilayered structures with thin air layers is studied in this paper. Two types of models are used to describe the vibro-acoustic behavior of these structures. Standard transfer matrix method assumes infinite layers and represents the plane wave propagation in the layers. A wave based model describes the direct sound transmission through a rectangular structure placed between two reverberant rooms. Full vibro-acoustic coupling between rooms, plates, and air cavities is taken into account. Comparison with double glazing measurements shows that this effect of vibro-acoustic coupling is important in lightweight double walls. For infinite structures, structural damping has no significant influence on STL below the coincidence frequency. In this frequency region, the non-resonant transmission or so-called mass-law behavior dominates sound transmission. Modal simulations suggest a large influence of structural damping on STL. This is confirmed by experiments with double fiberboard partitions and sandwich structures. The results show that for thin air layers, the damping induced by friction and viscous effects at the air gap surfaces can largely influence and improve the sound transmission characteristics.

Near field Rayleigh wave on soft porous layers.

Simulations performed for a typical semi-infinite reticulated plastic foam saturated by air show that, at distances less than three Rayleigh wavelengths from the area of mechanical excitation by a circular source, the normal frame velocity is close to the Rayleigh pole contribution. Simulated measurements show that a good order of magnitude estimate of the phase speed and damping can be obtained at small distances from the source. Simulations are also performed for layers of finite thickness, where the phase velocity and damping depend on frequency. They indicate that the normal frame velocity at small distances from the source is always close to the Rayleigh pole contribution and that a good order of magnitude estimate of the phase speed of the Rayleigh wave can be obtained at small distances from the source. Furthermore, simulations show that precise measurements of the damping of the Rayleigh wave need larger distances. Measurements performed on a layer of finite thickness confirm these trends.

Prediction of the sound field above a patchwork of absorbing materials.

The aim of this paper is to investigate the acoustic performance of sound absorbing materials through a numerical wave based prediction technique. The final goal of this work is to get insight into the acoustic behavior of a combination of sound absorbing patches. In order to address a wide frequency range, a model based on the Trefftz approach is adopted. In this approach, the dynamic field variables are expressed in terms of global wave function expansions that satisfy the governing dynamic equations exactly. Therefore, approximation errors are associated only with the boundary conditions of the considered problem. This results in a computationally efficient technique. The main advantage of this method is the fact that the sound absorbing patches do not have to be locally reacting. In this article, the wave based method is described and experimentally validated for the case of normal incidence sound absorption identification in a standing wave tube. Afterwards, the method is applied to simulate some interesting setups of absorbing materials.

Free field measurements of the absorption coefficient for nonlocally reacting sound absorbing porous layers.

A simple asymptotic approximation with two parameters (the plane wave reflection coefficient and a correction factor) has been derived by Brekhovskikh and Godin [Acoustics of Layered Media II. Point Sources and Bounded Beams (Springer, New York, 1992)], for the spherical field reflected by nonlocally reacting surfaces. In the present work, an expression for the correction factor is obtained for the case of a homogeneous and isotropic porous layer. A free field method for evaluating reflection and absorption coefficients with this approximation is presented. The evaluation of the absorption coefficient at normal incidence is performed on a porous layer on a rigid backing, and compared to measurements performed using a two microphone technique and an impedance tube.

Determination of mercury in human serum and packed blood cells by neutron activation analysis.

A method is described for the determination of mercury in human blood serum and packed blood cells employing neutron activation analysis. Great attention was devoted to the collection and manipulation of the samples. The accuracy and precision of the method were tested by analyzing biological reference materials and by comparing the concentrations measured in a number of serum samples to those obtained by another, independent technique (cold vapor atomic absorption spectrometry) in the same samples. The article reports the levels measured in blood serum and packed blood cells samples from 15 adult volunteers, as well as the figures determined in a "second-generation" biological reference material (freeze-dried human serum), prepared and conditioned at the University of Ghent.

Element concentrations in the air of an indoor shooting range.

Elemental emissions during firing in a shooting range were measured for different types of ammunition. When using Hirtenberger bullets, lead, barium, antimony and to a lesser extent copper and arsenic were the primary metal pollutants. Stationary sampling at three locations in the range did not reveal large concentration gradients. Large concentration variations were observed by sampling before, during and after shooting. Lead and antimony concentrations peak at 5060 and 119 micrograms m-3, respectively. Soil elements such as aluminium, sodium and calcium are enriched during shooting, probably due to soil resuspension by the shooters and the bullets hitting the sand backstop. After shooting has ceased the concentrations fall to within pre-shooting levels within a couple of hours. Measurement of the aerodynamic particle size shows low mass median diameters for the elements emitted during firing and larger diameters for the soil-associated elements. The peak airborne concentrations measured by stationary sampling, and human exposure measured by a personal sampler carried by an instructor were compared with threshold limit values. During the shooting the TLV is significantly exceeded for lead.