Torsional behaviour of Reciproc and Reciproc blue instruments associated with their martensitic transformation temperatures.

AIM: To compare the martensitic transformation temperatures and torsional resistance behaviour of classic M-Wire Reciproc and Reciproc blue files (VDW, Munich, Germany). METHODOLOGY: M-Wire classic Reciproc R25 and Reciproc blue R25 instruments were used. Transformation temperatures were determined by differential scanning calorimetry (DSC-DSC 60, Shimadzu, Kyoto, Japan). Three samples with approximately 20 mg of each system were cooled to -120 °C and then heated to 100 °C and then cooled to -100 °C at a rate of 10 °C min-1 . The maximum torque values and angular deflection until fracture of new instruments (n = 10) were measured according to ISO 3630-1. Results were analysed statistically using the Student's t-test at a significance level of P < 0.05. RESULTS: DSC results revealed the absence of martensitic transformation for Reciproc instruments in the temperature range analysed. In both systems, the instruments were composed of a mixture of R-phase and austenite at room temperature. After torsional tests, Reciproc blue had significantly lower values for mean maximum torque at rupture (P < 0.05), although the angular deflection values were significantly higher than the Reciproc classic group (P < 0.05). CONCLUSIONS: Both Reciproc and Reciproc blue instruments were composed of a mixture of R-phase and austenite. Reciproc Blue instruments had a greater angle of rotation to fracture but a lower torque to failure than M-Wire Reciproc instruments.

The influence of simulated clinical use on the flexibility of rotary ProTaper Universal, K3 and EndoSequence nickel-titanium instruments.

AIM: To investigate the influence of cyclic flexural and torsional loading on the flexibility of ProTaper Universal, K3 and EndoSequence nickel-titanium instruments, in view of the hypothesis that these types of loading would decrease the flexibility of the selected NiTi rotary files. METHODOLOGY: The instruments evaluated were S2 and F1 ProTaper Universal, sizes 20 and 25, .06 taper K3, and sizes 20 and 25, .06 taper EndoSequence. Flexibility was determined by 45° bending tests according to ISO 3630-1 specification. Values of the bending moment (MB ) obtained with new instruments were considered as the control group (CG). Bending tests were then conducted in instruments previously fatigued to one-fourth and three-fourths of their average fatigue life (fatigue groups, FG» and FG¾), as well as after cyclic torsional loading (torsional group, TG). Fatigue tests were carried out in a bench device that allowed the files to rotate freely inside an artificial canal with an angle of curvature of 45° and a radius of 5 mm. Cyclic torsional loading tests were performed that entailed rotating the instrument from zero angular deflection to 180° and then returning to zero applied torque in 20 cycles. Data were analysed using one-way analysis of variance at a significance level of 5%. RESULTS: Simulated clinical use by means of flexural fatigue tests did not affect the flexibility of the instruments, except for a significant increase in flexibility observed in a few instruments (P < 0.05). In addition, comparative statistical analyses between the values of MB measured in new instruments and after cyclic torsional loading showed no significant differences between them (P > 0.05). CONCLUSIONS: The flexibility of rotary ProTaper Universal, K3 and EndoSequence NiTi instruments, measured in bending tests, was not adversely affected by simulated clinical use in curved root canals.

Physical and mechanical properties of a thermomechanically treated NiTi wire used in the manufacture of rotary endodontic instruments.

AIM: To compare physical and mechanical properties of one conventional and one thermomechanically treated nickel-titanium (NiTi) wire used to manufacture rotary endodontic instruments. METHODOLOGY: Two NiTi wires 1.0 mm in diameter were characterized; one of them, C-wire (CW), was processed in the conventional manner, and the other, termed M-Wire (MW), received an additional heat treatment according to the manufacturer. Chemical composition was determined by energy-dispersive X-ray spectroscopy, phase constitution by XRD and the transformation temperatures by DSC. Tensile loading/unloading tests and Vickers microhardness measurements were performed to assess the mechanical behaviour. Data were analysed using analysis of variance (α = 0.05). RESULTS: The two wires showed approximately the same chemical composition, close to the 1 : 1 atomic ratio, and the ß-phase was the predominant phase present. B19' martensite and the R-phase were found in MW, in agreement with the higher transformation temperatures found in this wire compared with CW, whose transformation temperatures were below room temperature. Average Vickers microhardness values were similar for MW and CW (P = 0.91). The stress at the transformation plateau in the tensile load-unload curves was lower and more uniform in the M-Wire, which also showed the smallest stress hysteresis and apparent elastic modulus. CONCLUSIONS: The M-Wire had physical and mechanical properties that can render endodontic instruments more flexible and fatigue resistant than those made with conventionally processed NiTi wires.

Dimensional characterization and mechanical behaviour of K3 rotary instruments.

AIM: To correlate the mechanical behaviour in torsion, bending and fatigue tests of K3 instruments with their dimensional characteristics. METHODOLOGY: Instrument length, tip angle, distance between blades (pitch length) and the diameter at each millimetre from the tip of sizes 20, 25 and 30, 0.04 taper and sizes 20 and 25, 0.06 taper K3 rotary instruments were measured in an optical microscope equipped with digital micrometers. The cross-sectional area at 3 mm from the tip of the same instruments was determined using digital image analysis of scanning electron microscopy images. Maximum torque and angular deflection, as well as bending moment at 45 degrees were measured according to specification of ISO 3630-1. Fatigue resistance of instruments size 30, 0.04 taper, and sizes 20 and 25, 0.06 taper was determined in a fatigue test bench device. RESULTS: The analysed instruments presented no uniformity in the distance between adjacent blades, but the measured diameters at each millimetre from the tip were regular, showing compliance with manufacturing standards. Torque and bending moment of the tested instruments increased significantly with diameter and cross-sectional area at 3 mm from the instrument tip. The fatigue resistance of the instruments showed a tendency to decrease as the diameter of the instruments increased. CONCLUSIONS: The bending moment at 45 degrees and the torsional resistance of K3 instruments can be predicted using instrument diameter and cross-sectional area at 3 mm from the tip. Fatigue resistance decreased as the instrument diameter increased.

Influence of sterilization on mechanical properties and fatigue resistance of nickel-titanium rotary endodontic instruments.

AIM: To evaluate the effect of repeated sterilization cycles in dry oven or autoclave, on the mechanical behaviour and fatigue resistance of rotary endodontic Ni-Ti instruments. METHODOLOGY: New Ni-Ti instruments were subjected to five consecutive sterilization cycles in a dry oven or steam autoclave. Microhardness was measured in the nonmachined parts of the shanks of instruments using a Vickers indenter. Specimens of Ni-Ti wires were submitted to the same sterilization protocol and tensile tested until rupture. A group of instruments were fatigued to one half of their average fatigue life and then sterilized. New and sterilized instruments were fatigue tested until rupture. anova tests at alpha = 0.05 were used for statistical analysis. RESULTS: Sterilization procedures resulted in no significant changes in Vickers microhardness, nor in the parameters describing the mechanical behaviour of the wires. However, the number of cycles to failure was statistically higher for all instruments after dry heat or autoclave sterilization cycles. In the instruments previously fatigued to one half of their fatigue life, autoclave sterilization gave rise to an increase of 39% in the remaining number of cycles to failure. CONCLUSIONS: Changes in the mechanical properties of Ni-Ti endodontic instruments after five cycles of commonly used sterilization procedures were insignificant. The sterilization procedures are safe as they produced a significant increase in the fatigue resistance of the instruments.