Chemometric tools applied to optimize a fast solid-phase microextraction method for analysis of polycyclic aromatic hydrocarbons in produced water.

Chemometric tools are powerful strategies to efficiently optimize many processes. These tools were employed to optimize a fast-solid phase microextraction procedure, which was used for the analysis of polycyclic aromatic hydrocarbons (PAHs) in oil-based produced water using a Headspace-Solid Phase Microextraction technique (HS-SPME/GC-MS). This optimization was achieved with a 24 factorial design approach, where the final conditions for this extraction procedure were 10 µg L-1, 1 h, 92 °C (at headspace), and 0.62 mol L-1 for PAHs concentration, fiber exposition to headspace, temperature, and NaCl concentration, respectively. The limit of detection (LOD) in this protocol ranged from 0.2 to 41.4 ng L-1, while recovery values from 67.65 to 113.10%. Besides that, relative standard deviation (RSD) were lower than 8.39% considering high molecular weight compounds. Moreover, the proposed methodology in this work does not require any previous treatment of the sample and allows to quantify a higher number of PAHs. Notably, naphthalene was the major PAHs compound quantified in all samples of the produced water at 99.99 µg L-1. Altogether, these results supported this methodology as a suitable analytical strategy for fast determination of PAHs in produced water from oil-based industry.

Reactive Adsorption of Parabens on Synthesized Micro- and Mesoporous Silica from Coal Fly Ash: pH Effect on the Modification Process.

Parabens are widely used as preservatives in food, pharmaceutical, and cosmetic products. These compounds are known for their estrogen agonist activity. This research investigates the synthesis of micro- and mesoporous silica from coal fly ash at different pH values (13, 11, 9, and 7) as well as its use as an adsorbent for the removal of parabens. The materials were characterized, and X-ray fluorescence (XRF) analysis revealed that the fly ash acid treatment reduced the presence of aluminum, iron, and calcium oxides and also that silica synthesized at lower pH values (7 and 9) showed a higher SiO2 content. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses revealed microporous silica formation for silica synthesized at pH 13 and mesoporous silica at pH 7, 9, and 11. Adsorption tests were performed with materials, and FA-AT7 showed a higher adsorption capacity. The effect of factors (A) adsorbent mass, (B) initial paraben concentration, and (C) agitation rate on the adsorption process was studied for the FA-AT7 adsorbent using a factorial experimental design. Standardized Pareto charts revealed a negative effect of factor A, positive effect of factor B, and negative interaction effects of factors A-B for all studied parabens. Isotherms and multicomponent kinetic studies were performed. A linear type-III isotherm was obtained, and adsorption equilibrium was reached at approximately 10 min.

Application of the QuEChERS method for the determination of organochlorine pesticide residues in Brazilian fruit pulps by GC-ECD.

The Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method was applied to the extraction of 14 organochlorine pesticides (OCPs) residues from commercial fruit pulps available in supermarkets in Fortaleza, Northeastern Brazil. The analyses were carried out by gas chromatography (GC), coupled to an electron-capture detector (ECD), and were confirmed by GC-tandem mass spectrometry (MS). The parameters of the analytical method, such as accuracy, precision, linear range, limits of detection and quantification, were determined for each pesticide. The results showed good linearity (R2 ≥ 0.9916) and the overall average recoveries were considered satisfactory obtaining values between 69 and 110%, RSD of 2-15 %, except for hexachlorobenzene (HCB) in açai, acerola and guava pulp samples. The OCPs were detected in guava (α-HCH; lindane) and soursop (α, ß-HCH isomers) samples. The QuEChERS method and GC-ECD were successfully used to analyze OCPs in commercially available Brazilian fruit pulps and can be applied in routine analytical laboratories.

Effect of nanoporous carbon surface chemistry on the removal of endocrine disruptors from water phase.

Wood-based activated carbon and its sulfur-doped counterpart were used as adsorbents of endocrine disruptor chemicals (EDC) from aqueous solution. Adsorption process was carried out in dynamic conditions and Thomas model was used to predict the performance of the column. The results showed a good fitting of the theoretical curve to the experimental data. S-doped carbon exhibited a higher adsorption capacity of trimethoprim (TMP) and smaller of sulfamethoxazole (SMX) and diclofenac (DCF) in comparison with the carbon with no sulfur incorporated into the matrix. The surface features of the initial carbons and those exposed to EDC were evaluated in order to derive the adsorption mechanism and elucidate the role of surface features. An increase in the amount of TMP from a low concentration solution (10 mg/L) on sulfur-doped carbon was linked to acid-base interactions and the reactive adsorption/oxidation of TMP. A decrease in SMX and DCF after sulfur doping was explained by a considerable increase in surface hydrophobicity, which does not favor the retention of polar DCF and SMX molecules. When the adsorption was measured from a high concentration solution at equilibrium conditions at the dark or under solar light irradiation different trends in the adsorption capacities were found. This was linked to the photoactivity of carbons and the degradation of EDC in the pore system promoted by visible light followed by the adsorption of the products of surface reactions.

Treatment influence on green coconut shells for removal of metal ions: pilot-scale fixed-bed column.

This work investigates copper, nickel and zinc ion biosorption in single- and multi-component systems in a fixed-bed column using green coconut shells (CS). Approximately 85% of biosorbents are in a particle size ranging from 0.25 to 2 mm. Operational parameters selected include a flow rate of 200 mL min-1 and a bed height of 100 cm, which were selected for a shorter execution time and good adsorption capacity. Empty-bed contact time and Thomas models were applied, showing a good fit with the experimental data. The column adsorption capacity increased after the green CS powder was treated in a column with NaOH at a concentration of 0.1 mol L-1. The highest values of adsorption capacities founded were 0.69, 0.45 and 0.39 mmol L-1 for Cu(II), Ni(II) and Zn(Il), respectively, using green CS treated inside a column with NaOH of 0.1 M. The pH and chemical oxygen demand were monitored in the treatment solution and indicated that the adjustment of these parameters is necessary before disposal of these solutions. A study of desorption using an acid solution was carried out for recovery of metal ions.

Occurrence and removal of estrogens in Brazilian wastewater treatment plants.

This paper evaluated the occurrence and removal efficiency of four estrogenic hormones in five biological wastewater treatment plants (WWTPs), located in the State of Ceará, Brazil. The five WWTPs comprised: two systems consisted of one facultative pond followed by two maturation ponds, one facultative pond, one activated sludge (AS) system followed by a chlorination step, and one upflow anaerobic sludge blanket (UASB) reactor followed by a chlorination step. Estrogen occurrence showed a wide variation among the analyzed influent and effluent samples. Estrone (E1) showed the highest occurrence in the influent (76%), whereas both 17ß-estradiol (E2) and 17α-ethynylestradiol (EE2) presented a 52% occurrence, and the compound 17ß-estradiol 17-acetate (E2-17A), a 32% one. The occurrence in the effluent samples was 48% for E1, 28% for E2, 12% for E2-17A, and 40% for EE2. The highest concentrations of E1 and EE2 hormones in the influent were 3050 and 3180 ng L(-1), respectively, whereas E2 and E2-17A had maximum concentrations of 776 and 2300 ng L(-1), respectively. The lowest efficiencies for the removal of estrogenic hormones were found in WWTP consisted of waste stabilization ponds, ranging from 54 to 79.9%. The high-rate systems (AS and UASB), which have chlorination as post-treatment, presented removal efficiencies of approximately 95%.

Chemometric characterization of alembic and industrial sugar cane spirits from cape verde and ceará, Brazil.

Sugar cane spirits are some of the most popular alcoholic beverages consumed in Cape Verde. The sugar cane spirit industry in Cape Verde is based mainly on archaic practices that operate without supervision and without efficient control of the production process. The objective of this work was to evaluate samples of industrial and alembic sugar cane spirits from Cape Verde and Ceará, Brazil using principal component analysis. Thirty-two samples of spirits were analyzed, twenty from regions of the islands of Cape Verde and twelve from Ceará, Brazil. Of the samples obtained from Ceará, Brazil seven are alembic and five are industrial spirits. The components analyzed in these studies included the following: volatile organic compounds (n-propanol, isobutanol, isoamylic, higher alcohols, alcoholic grade, acetaldehyde, acetic acid, acetate); copper; and sulfates.

BTEX removal from aqueous solutions by HDTMA-modified Y zeolite.

Various technologies have been used for the treatment and remediation of areas contaminated by BTEX (benzene, toluene, ethylbenzene and xylenes), which are organic compounds that are of particular concern due to their toxicity. Potential applications of synthetic zeolites for environmental fieldwork have also been reported worldwide. In this work, a hexadecyltrimethyl ammonium (HDTMA) surfactant-modified synthetic zeolite was investigated for its efficiency in removing BTEX from aqueous solutions. Three surfactant-modified zeolites were synthesized, with amounts of surfactant corresponding to 50%, 100%, and 200% of the total cation-exchange capacity (CEC) of the synthetic zeolite Y. The results of the BTEX adsorption experiments onto both synthetic zeolite and surfactant-modified zeolites (SMZ) showed that the SMZ-100 (zeolite modified with surfactant levels at 100% of CEC) was the most efficient modified zeolite for BTEX removal. Kinetics studies indicated that the multicomponent adsorption equilibrium was reached within 6 h and followed pseudo-second-order kinetics. The Langmuir, Freundlich, Redlich-Peterson and Temkin models were used to evaluate the BTEX adsorption capacity by SMZ-100. The Temkin model was found to be suitable for all BTEX compounds in a multicomponent system. Regeneration cycles of the modified zeolite were also performed, and the results showed that the adsorbent could be used efficiently in as many as four adsorption cycles, except for benzene.

Adsorption of BTX (benzene, toluene, o-xylene, and p-xylene) from aqueous solutions by modified periodic mesoporous organosilica.

The capacity of a periodic mesoporous organosilica (PMO) to adsorb the aromatic compounds benzene, toluene, o-, and p-xylenes (BTX), which are usually present in produced waters, was investigated under both column and batch processes. The PMO was synthesized by condensation of 1,4 bis(triethoxisilyl)benzene (BTEB) under acidic conditions by using structure-directing agent (SDA) Pluronic P123 in the presence of KCl. Thermogravimetric analysis showed that the presence of the surfactant decreases the thermal stability of the PMO. The small-angle X-ray diffraction pattern, as well as the nitrogen adsorption/desorption isotherm measurements, revealed that the synthesized material has a crystalline structure, with hexagonally-ordered cylindrical mesopores. The adsorption kinetics study indicated an adsorption equilibrium time of 50 min and also showed that the data best fitted the pseudo-first order kinetic model. The intraparticle diffusion model was also tested and pointed to the occurrence of such process in all cases. Both Langmuir and Temkin models best represented the adsorption isotherms of toluene; Langmuir and Redlich-Peterson models best represented the data obtained for the other compounds. Adsorption capacity decreases in the order benzene>o-xylene>p-xylene>toluene. Satisfactory results were observed in the application of the synthesized PMO for the removal of BTX from aqueous solution.

Adsorption of polycyclic aromatic hydrocarbons from aqueous solutions by modified periodic mesoporous organosilica.

A novel procedure was developed for the synthesis of a periodic mesoporous organosilica (PMO), which was used to remove polycyclic aromatic hydrocarbons (PAHs) from aqueous solutions. Adsorption equilibrium isotherms and adsorption kinetics experiments were carried out in solutions of PAHs (2-60 mg L(-1)), using the PMO as adsorbent. Adsorption models were used to predict the mechanisms involved. The adsorption kinetics data best fitted the pseudo-first-order kinetic model for naphthalene, and to the pseudo-second-order model for fluorene, fluoranthene, pyrene, and acenaphtene. The intraparticle model was also tested and pointed to the occurrence of such processes in all cases. The isotherm models which best represented the data obtained were the Freundlich model for fluoranthene, pyrene, and fluorene, the Temkin model for naphthalene, and the Redlich-Peterson model for acenaphtene. PAHs showed similar behavior regarding kinetics after 24 h of contact between adsorbent and PAHs. FTIR, XRD, BET, and SEM techniques were used for the characterization of the adsorbent material.