A Novel Cryogenic Approach to 3D Printing Cytocompatible, Conductive, Hydrogel-Based Inks.

In the field of tissue engineering and regenerative medicine, developing cytocompatible 3D conductive scaffolds that mimic the native extracellular matrix is crucial for the engineering of excitable cells and tissues. In this study, a custom cryogenic extrusion 3D printer was developed, which afforded control over both the ink and printing surface temperatures. Using this approach, aqueous inks were printed into well-defined layers with high precision. A conductive hydrogel ink was developed from chitosan (CS) and edge-functionalised expanded graphene (EFXG). Different EFXG:CS ratios (between 60:40 and 80:20) were evaluated to determine both conductivity and printability. Using the novel customized cryogenic 3D printer, conductive structures of between 2 and 20 layers were produced, with feature sizes as small as 200 µm. The printed structures are mechanically robust and are electrically conducting. The highest Young's modulus and conductivity in a hydrated state were 2.6 MPa and ∼45 S/m, respectively. Cytocompatibility experiments reveal that the developed material supports NSC-34 mouse motor neuron-like cells in terms of viability, attachment, and proliferation. The distinctive mechanical and electrical properties of the 3D-printed structures would make them good candidates for the engineering of 3D-structured excitable cells. Moreover, this novel printing setup can be used to print other hydrogel-based inks with high precision and resolution.

Copper/Polyaniline Interfaces Confined CO2 Electroreduction for Selective Hydrocarbon Production.

Polyaniline (PANI) provides an attractive organic platform for CO2 electrochemical reduction due to the ability to adsorb CO2 molecules and in providing means to interact with metal nanostructures. In this work, a novel PANI supported copper catalyst has been developed by coupling the interfacial polymerization of PANI and Cu nanoparticles. The hybrid catalyst demonstrates excellent activity towards production of hydrocarbon products including CH4 and C2H4, compared with the use of bare Cu nanoparticles. A faradaic efficiency of 71.8% and a current density of 16.9 mA/cm2 were achieved at -0.86V vs. RHE, in contrast to only 22.2% and 1.0 mA/cm2 from the counterpart Cu catalysts. The remarkably enhanced catalytic performance of the hybrid PANI/Cu catalyst can be attributed to the synergistic interaction between the PANI underlayer and copper nanoparticles. The PANI favours the adsorption and binding of CO2 molecules via its nitrogen sites to form *CO intermediates, while the Cu/PANI interfaces confine the diffusion or desorption of the *CO intermediates favouring their further hydrogenation or carbon-carbon coupling to form hydrocarbon products. This work provides insights into the formation of hydrocarbon products on PANI-modified Cu catalysts, which may guide the development of conducting polymer-metal catalysts for CO2 electroreduction.

Co-culture of chondrocytes and stem cells: a review of head and neck cell lines for cartilage regeneration.

INTRODUCTION: Bioprinting, using "bio-inks" consisting of living cells, supporting structures and biological motifs to create customized constructs, is an emerging technique that aims to overcome the challenges of cartilaginous reconstruction of head and neck structures. Several living cell lines and culturing methods have been explored as bio-inks with varying efficacy. Co-culture of primary chondrocytes and stem cells (SCs) is one technique, well established for degenerative joint disease treatment, with potential for use in expanding chondrocyte populations for bio-inks. This study aims to evaluate the techniques for co-culture of primary chondrocytes and SCs for head and neck cartilage regeneration. METHODS: A literature review was performed through OVID/Web of Science/MEDLINE/BIOSIS Previews/Embase. Studies reporting on chondrocytes and SCs in conjunction with co-culture or cartilage regeneration were included. Studies not reporting on findings from chondrocytes/SCs of the head and neck were excluded. Extracted data included cell sources, co-culture ratios and histological, biochemical and clinical outcomes. RESULTS: 15 studies met inclusion criteria. Auricular cartilage was the most common chondrocyte source (n=10), then nasal septum (n=5), articular (n=1) and tracheal cartilage (n=1). Bone marrow was the most common SC source (n=9) then adipose tissue (n=7). Techniques varied, with co-culture ratios ranging from 1:1 to 1:10. All studies reported co-culture to be superior to SC mono-culture by all outcomes. Most studies reported superiority or equivalence of co-culture to chondrocyte mono-culture by all outcomes. When comparing clinical outcomes, co-culture constructs were equivalent to chondrocyte mono-culture in diameter, and equivalent or inferior in wet weight and height. CONCLUSION: Co-culture of primary chondrocytes and SCs is a promising technique for expanding chondrocyte populations, with at least equivalence to chondrocyte mono-culture and superior to SC mono-culture when seeded at the same chondrocyte densities. However, there remains a lack of consensus regarding the optimal cell sources and co-culture ratios.

Microphysiological Constructs and Systems: Biofabrication Tactics, Biomimetic Evaluation Approaches, and Biomedical Applications.

In recent decades, microphysiological constructs and systems (MPCs and MPSs) have undergone significant development, ranging from self-organized organoids to high-throughput organ-on-a-chip platforms. Advances in biomaterials, bioinks, 3D bioprinting, micro/nanofabrication, and sensor technologies have contributed to diverse and innovative biofabrication tactics. MPCs and MPSs, particularly tissue chips relevant to absorption, distribution, metabolism, excretion, and toxicity, have demonstrated potential as precise, efficient, and economical alternatives to animal models for drug discovery and personalized medicine. However, current approaches mainly focus on the in vitro recapitulation of the human anatomical structure and physiological-biochemical indices at a single or a few simple levels. This review highlights the recent remarkable progress in MPC and MPS models and their applications. The challenges that must be addressed to assess the reliability, quantify the techniques, and utilize the fidelity of the models are also discussed.

Multiscale Structural Design of 2D Nanomaterials-based Flexible Electrodes for Wearable Energy Storage Applications.

2D nanomaterials play a critical role in realizing high-performance flexible electrodes for wearable energy storge devices, owing to their merits of large surface area, high conductivity and high strength. The electrode is a complex system and the performance is determined by multiple and interrelated factors including the intrinsic properties of materials and the structures at different scales from macroscale to atomic scale. Multiscale design strategies have been developed to engineer the structures to exploit full potential and mitigate drawbacks of 2D materials. Analyzing the design strategies and understanding the working mechanisms are essential to facilitate the integration and harvest the synergistic effects. This review summarizes the multiscale design strategies from macroscale down to micro/nano-scale structures and atomic-scale structures for developing 2D nanomaterials-based flexible electrodes. It starts with brief introduction of 2D nanomaterials, followed by analysis of structural design strategies at different scales focusing on the elucidation of structure-property relationship, and ends with the presentation of challenges and future prospects. This review highlights the importance of integrating multiscale design strategies. Finding from this review may deepen the understanding of electrode performance and provide valuable guidelines for designing 2D nanomaterials-based flexible electrodes.

Electrocatalysis of nitrogen pollution: transforming nitrogen waste into high-value chemicals.

On 16 June 2023, the United Nations Environment Programme highlighted the severity of nitrogen pollution faced by humans and called for joint action for sustainable nitrogen use. Excess nitrogenous waste (NW: NO, NO2, NO2-, NO3-, etc.) mainly arises from the use of synthetic fertilisers, wastewater discharge, and fossil fuel combustion. Although the amount of NW produced can be minimised by reducing the use of nitrogen fertilisers and fossil fuels, the necessity to feed seven billion people on Earth limits the utility of this approach. Compared to current industrial processes, electrocatalytic NW reduction or CO2-NW co-reduction offers a potentially greener alternative for recycling NW and producing high-value chemicals. However, upgrading this technology to connect upstream and downstream industrial chains is challenging. This viewpoint focuses on electrocatalytic NW reduction, a cutting-edge technology, and highlights the challenges in its practical application. It also discusses future directions to meet the requirements of upstream and downstream industries by optimising production processes, including the pretreatment and supply of nitrogenous raw materials (e.g. flue gas and sewage), design and macroscopic preparation of electrocatalysts, and upscaling of reactors and other auxiliary equipment.

Lattice Distortion and H-passivation in Pure Carbon Electrocatalysts for Efficient and Stable Two-electron Oxygen Reduction to H2 O2.

The exploration of inexpensive and efficient catalysts for oxygen reduction reaction (ORR) is crucial for chemical and energy industries. Carbon materials have been proved promising with different catalysts enabling 2 and 4e- ORR. Nevertheless, their ORR activity and selectivity is still complex and under debate in many cases. Many structures of these active carbon materials are also chemically unstable for practical implementations. Unlike the well-discussed structures, this work presents a strategy to promote efficient and stable 2e- ORR of carbon materials through the synergistic effect of lattice distortion and H-passivation (on the distorted structure). We show how these structures can be formed on carbon cloth, and how the reproducible chemical adsorption can be realized on these structures for efficient and stable H2 O2 production. The work here gives not only new understandings on the 2e- ORR catalysis, but also the robust catalyst which can be directly used in industry.

Fabrication and Characterization of an Electro-Compacted Collagen/Elastin/Hyaluronic Acid Sheet as a Potential Skin Scaffold.

The development of biomimetic structures with integrated extracellular matrix (ECM) components represents a promising approach to biomaterial fabrication. Here, an artificial ECM, comprising the structural protein collagen I and elastin (ELN), as well as the glycosaminoglycan hyaluronan (HA), is reported. Specifically, collagen and ELN are electrochemically aligned to mimic the compositional characteristics of the dermal matrix. HA is incorporated into the electro-compacted collagen-ELN matrices via adsorption and chemical immobilization, to give a final composition of collagen/ELN/HA of 7:2:1. This produces a final collagen/ELN/hyaluronic acid scaffold (CEH) that recapitulates the compositional feature of the native skin ECM. This study analyzes the effect of CEH composition on the cultivation of human dermal fibroblast cells (HDFs) and immortalized human keratinocytes (HaCaTs). It is shown that the CEH scaffold supports dermal regeneration by promoting HDFs proliferation, ECM deposition, and differentiation into myofibroblasts. The CEH scaffolds are also shown to support epidermis growth by supporting HaCaTs proliferation, differentiation, and stratification. A double-layered epidermal-dermal structure is constructed on the CEH scaffold, further demonstrating its ability in supporting skin cell function and skin regeneration.

Edge-Functionalized Graphene/Polydimethylsiloxane Composite Films for Flexible Neural Cuff Electrodes.

The design of neural electrodes has changed in the past decade, driven mainly by the development of new materials that open the possibility of manufacturing electrodes with adaptable mechanical properties and promising electrical properties. In this paper, we report on the mechanical and electrochemical properties of a polydimethylsiloxane (PDMS) composite with edge-functionalized graphene (EFG) and demonstrate its potential for use in neural implants with the fabrication of a novel neural cuff electrode. We have shown that a 200 µm thick 1:1 EFG/PDMS composite film has a stretchability of up to 20%, a Young's modulus of 2.52 MPa, and a lifetime of more than 10000 mechanical cycles, making it highly suitable for interfacing with soft tissue. Electrochemical characterization of the EFG/PDMS composite film showed that the capacitance of the composite increased up to 35 times after electrochemical reduction, widening the electrochemical water window and remaining stable after soaking for 5 weeks in phosphate buffered saline. The electrochemically activated EFG/PDMS electrode had a 3 times increase in the charge injection capacity, which is more than double that of a commercial platinum-based neural cuff. Electrochemical and spectrochemical investigations supported the conclusion that this effect originated from the stable chemisorption of hydrogen on the graphene surface. The biocompatibility of the composite was confirmed with an in vitro cell culture study using mouse spinal cord cells. Finally, the potential of the EFG/PDMS composite was demonstrated with the fabrication of a novel neural cuff electrode, whose double-layered and open structured design increased the cuff stretchability up to 140%, well beyond that required for an operational neural cuff. In addition, the cuff design offers better integration with neural tissue and simpler nerve fiber installation and locking.

Polyethylene Oxide (PEO) Provides Bridges to Silica Nanoparticles to Form a Shear Thickening Electrolyte for High Performance Impact Resistant Lithium-ion Batteries.

The development of shear thickening electrolytes is proving to be pivotal in the quest for impact resistant lithium-ion batteries (LIBs). However, the high viscosity and poor stability associated with the need for high filler content has to date impeded progress. Here, this work reports a new type of polymer-bridged shear thickening electrolyte that overcomes these shortcomings, by utilizing the interaction between polymer chains and silica nanoparticles. The incorporation of polyethylene oxide (PEO) facilitates hydrocluster formation providing impact resistance with a filler content as low as 2.2 wt%. This low viscosity electrolyte has a high ionic conductivity of ≈5.1 mS cm-1 with excellent long-term stability, over 30 days. The effectiveness of this electrolyte in LIBs is demonstrated by excellent electrochemical performance and high impact resistance.

The regulatory challenge of 3D bioprinting.

New developments in additive manufacturing and regenerative medicine have the potential to radically disrupt the traditional pipelines of therapy development and medical device manufacture. These technologies present a challenge for regulators because traditional regulatory frameworks are designed for mass manufactured therapies, rather than bespoke solutions. 3D bioprinting technologies present another dimension of complexity through the inclusion of living cells in the fabrication process. Herein we overview the challenge of regulating 3D bioprinting in comparison to existing cell therapy products as well as custom-made 3D printed medical devices. We consider a range of specific challenges pertaining to 3D bioprinting in regenerative medicine, including classification, risk, standardization and quality control, as well as technical issues related to the manufacturing process and the incorporated materials and cells.

Novel Collagen Surgical Patches for Local Delivery of Multiple Drugs.

Effective control of post-operative inflammation after tissue repair remains a clinical challenge. A tissue repair patch that could appropriately integrate into the surrounding tissue and control inflammatory responses would improve tissue healing. A collagen-based hybrid tissue repair patch has been developed in this work for the local delivery of an anti-inflammatory drug. Dexamethasone (DEX) was encapsulated into PLGA microspheres and then co-electrocompacted into a collagen membrane. Using a simple process, multiple drugs can be loaded into and released from this hybrid composite material simultaneously, and the ratio between each drug is controllable. Anti-inflammatory DEX and the anti-epileptic phenytoin (PHT) were co-encapsulated and released to validate the dual drug delivery ability of this versatile composite material. Furthermore, the Young's modulus of this drug-loaded collagen patch was increased to 20 KPa using a biocompatible riboflavin (vitamin B2)-induced UV light cross-linking strategy. This versatile composite material has a wide range of potential applications which deserve exploration in further research.

Hydrogels for RNA delivery.

RNA-based therapeutics have shown tremendous promise in disease intervention at the genetic level, and some have been approved for clinical use, including the recent COVID-19 messenger RNA vaccines. The clinical success of RNA therapy is largely dependent on the use of chemical modification, ligand conjugation or non-viral nanoparticles to improve RNA stability and facilitate intracellular delivery. Unlike molecular-level or nanoscale approaches, macroscopic hydrogels are soft, water-swollen three-dimensional structures that possess remarkable features such as biodegradability, tunable physiochemical properties and injectability, and recently they have attracted enormous attention for use in RNA therapy. Specifically, hydrogels can be engineered to exert precise spatiotemporal control over the release of RNA therapeutics, potentially minimizing systemic toxicity and enhancing in vivo efficacy. This Review provides a comprehensive overview of hydrogel loading of RNAs and hydrogel design for controlled release, highlights their biomedical applications and offers our perspectives on the opportunities and challenges in this exciting field of RNA delivery.

A biocompatible and fully erodible conducting polymer enables implanted rechargeable Zn batteries.

Implanted rechargeable batteries that can provide energy over a sufficient lifetime and ultimately degrade into non-toxic byproducts are highly desirable. However, their advancement is significantly impeded by the limited toolbox of electrode materials with a known biodegradation profile and high cycling stability. Here we report biocompatible, erodible poly(3,4-ethylenedioxythiophene) (PEDOT) grafted with hydrolyzable carboxylic acid pendants. This molecular arrangement combines the pseudocapacitive charge storage from the conjugated backbones and dissolution via hydrolyzable side chains. It demonstrates complete erosion under aqueous conditions in a pH-dependent manner with a predetermined lifetime. The compact rechargeable Zn battery with a gel electrolyte offers a specific capacity of 31.8 mA h g-1 (57% of theoretical capacity) and outstanding cycling stability (78% capacity retention over 4000 cycles at 0.5 A g-1). Subcutaneous implantation of this Zn battery into Sprague-Dawley (SD) rats demonstrates complete biodegradation in vivo and biocompatibility. This molecular engineering strategy presents a viable avenue for developing implantable conducting polymers with a predetermined degradation profile and high energy storage capability.

Biopolymeric Coatings for Local Release of Therapeutics from Biomedical Implants.

The deployment of structures that enable localized release of bioactive molecules can result in more efficacious treatment of disease and better integration of implantable bionic devices. The strategic design of a biopolymeric coating can be used to engineer the optimal release profile depending on the task at hand. As illustrative examples, here advances in delivery of drugs from bone, brain, ocular, and cardiovascular implants are reviewed. These areas are focused to highlight that both hard and soft tissue implants can benefit from controlled localized delivery. The composition of biopolymers used to achieve appropriate delivery to the selected tissue types, and their corresponding outcomes are brought to the fore. To conclude, key factors in designing drug-loaded biopolymeric coatings for biomedical implants are highlighted.

Electro-compacted collagen for corneal epithelial tissue engineering.

Bioengineered corneal substitutes offer a solution to the shortage of donor corneal tissue worldwide. As one of the major structural components of the cornea, collagen has shown great potential for tissue-engineered cornea substitutes. Herein, free-standing collagen membranes fabricated using electro-compaction were assessed in corneal bioengineering application by comparing them with nonelectro-compacted collagen (NECC). The well-organized and biomimetic fibril structure resulted in a significant improvement in mechanical properties. A 10-fold increase in tensile and compressive modulus was recorded when compared with NECC membranes. In addition to comparable transparency in the visible light range, the glucose permeability of the electro-compacted collagen (ECC) membrane is higher than that of the native human cornea. Human corneal epithelial cells adhere and proliferate well on the ECC membrane, with a large cell contact area observed. The as-described ECC has appropriate structural, topographic, mechanical, optical, glucose permeable, and cell support properties to provide a platform for a bioengineered cornea; including the outer corneal epithelium and potentially deeper corneal tissues.

An integrated Mg battery-powered iontophoresis patch for efficient and controllable transdermal drug delivery.

Wearable transdermal iontophoresis eliminating the need for external power sources offers advantages for patient-comfort when deploying epidermal diseases treatments. However, current self-powered iontophoresis based on energy harvesters is limited to support efficient therapeutic administration over the long-term operation, owing to the low and inconsistent energy supply. Here we propose a simplified wearable iontophoresis patch with a built-in Mg battery for efficient and controllable transdermal delivery. This system decreases the system complexity and form factors by using viologen-based hydrogels as an integrated drug reservoir and cathode material, eliminating the conventional interface impedance between the electrode and drug reservoir. The redox-active polyelectrolyte hydrogel offers a high energy density of 3.57 mWh cm-2, and an optimal bioelectronic interface with ultra-soft nature and low tissue-interface impedance. The delivery dosage can be readily manipulated by tuning the viologen hydrogel and the iontophoresis stimulation mode. This iontophoresis patch demonstrates an effective treatment of an imiquimod-induced psoriasis mouse. Considering the advantages of being a reliable and efficient energy supply, simplified configuration, and optimal electrical skin-device interface, this battery-powered iontophoresis may provide a new non-invasive treatment for chronic epidermal diseases.

Optimizing the composition of gelatin methacryloyl and hyaluronic acid methacryloyl hydrogels to maximize mechanical and transport properties using response surface methodology.

Hydrogel materials are promising candidates in cartilage tissue engineering as they provide a 3D porous environment for cell proliferation and the development of new cartilage tissue. Both the mechanical and transport properties of hydrogel scaffolds influence the ability of encapsulated cells to produce neocartilage. In photocrosslinkable hydrogels, both of these material properties can be tuned by changing the crosslinking density. However, the interdependent nature of the structural, physical and biological properties of photocrosslinkable hydrogels means that optimizing composition is typically a complicated process, involving sequential and/or iterative steps of physiochemical and biological characterization. The combinational nature of the variables indicates that an exhaustive analysis of all reasonable concentration ranges would be impractical. Herein, response surface methodology (RSM) was used to efficiently optimize the composition of a hybrid of gelatin-methacryloyl (GelMA) and hyaluronic acid methacryloyl (HAMA) with respect to both mechanical and transport properties. RSM was employed to investigate the effect of GelMA, HAMA, and photoinitiator concentration on the shear modulus and diffusion coefficient of the hydrogel membrane. Two mathematical models were fitted to the experimental data and used to predict the optimum hydrogel composition. Finally, the optimal composition was tested and compared with the predicted values.

Development of 3D printable graphene oxide based bio-ink for cell support and tissue engineering.

Tissue engineered constructs can serve as in vitro models for research and replacement of diseased or damaged tissue. As an emerging technology, 3D bioprinting enables tissue engineering through the ability to arrange biomaterials and cells in pre-ordered structures. Hydrogels, such as alginate (Alg), can be formulated as inks for 3D bioprinting. However, Alg has limited cell affinity and lacks the functional groups needed to promote cell growth. In contrast, graphene oxide (GO) can support numerous cell types and has been purported for use in regeneration of bone, neural and cardiac tissues. Here, GO was incorporated with 2% (w/w) Alg and 3% (w/w) gelatin (Gel) to improve 3D printability for extrusion-based 3D bioprinting at room temperature (RT; 25°C) and provide a 3D cellular support platform. GO was more uniformly distributed in the ink with our developed method over a wide concentration range (0.05%-0.5%, w/w) compared to previously reported GO containing bioink. Cell support was confirmed using adipose tissue derived stem cells (ADSCs) either seeded onto 3D printed GO scaffolds or encapsulated within the GO containing ink before direct 3D printing. Added GO was shown to improve cell-affinity of bioinert biomaterials by providing more bioactive moieties on the scaffold surface. 3D cell-laden or cell-seeded constructs showed improved cell viability compared to pristine (without GO) bio-ink-based scaffolds. Our findings support the application of GO for novel bio-ink formulation, with the potential to incorporate other natural and synthetic materials such as chitosan and cellulose for advanced in situ biosensing, drug-loading and release, and with the potential for electrical stimulation of cells to further augment cell function.