Gigahertz-Based Visible Light Detection Enabled via CdS-Coated TiO2 Nanotube Layers.

Detection of visible light is a key component in material characterization techniques and often a key component of quality or purity control analyses for health and safety applications. Here in this work, to enable visible light detection at gigahertz frequencies, a planar microwave resonator is integrated with high aspect ratio TiO2 nanotube (TNT) layer-sensitized CdS coating using the atomic layer deposition (ALD) technique. This unique method of visible light detection with microwave-based sensing improves integration of the light detection devices with digital technology. The designed planar microwave resonator sensor was implemented and tested with resonant frequency between 8.2 and 8.4 GHz and a resonant amplitude between -15 and -25 dB, depending on the wavelength of the illuminated light illumination on the nanotubes. The ALD CdS coating sensitized the nanotubes in visible light up to ∼650 nm wavelengths, as characterized by visible spectroscopy. Furthermore, CdS-coated TNT layer integration with the planar resonator sensor allowed for development of a robust microwave sensing platform with improved sensitivity to green and red light (60 and 1300%, respectively) compared to the blank TNT layers. Moreover, the CdS coating of the TNT layer enhanced the sensor's response to light exposure and resulted in shorter recovery times once the light source was removed. Despite having a CdS coating, the sensor was capable of detecting blue and UV light; however, refining the sensitizing layer could potentially enhance its sensitivity to specific wavelengths of light in certain applications.

High-Frequency TiO2 Nanotube-Adapted Microwave Coplanar Waveguide Resonator for High-Sensitivity Ultraviolet Detection.

Ultraviolet (UV) sensors are a key component in growing applications such as water quality treatment and environmental monitoring, with considerable interest in their miniaturization and enhanced operation. This work presents a passive gold coplanar waveguide split ring resonator integrated with anodic self-organized TiO2 nanotube (TNT) membranes with a thickness of 20 µm to provide real-time UV detection. The resonator operated as a one-port device to capture the reflection coefficient (S11) signal, with a center frequency of 16 GHz and a notch amplitude of -88 dB. It was experimentally analyzed for its UV sensing capability in the range of 36.5-463 µW/cm2. The high-frequency resonator was improved through design choices including the addition of a tapered input transmission line, wire bonding for practical device design, and an interdigitated capacitive ring gap. The high frequency also helped mitigate noise due to water vapor or environmental contaminants. S11 amplitude variation was found through both experiments and modeling to follow a linear trend with UV illumination intensity. The resonator exhibited over 45 ± 2 dB shift in the resonant amplitude under the highest UV illumination conditions, with a sensitivity of 0.084 dB/µW cm-2 and the potential to sense UV intensity as low as 2.7 µW/cm2. The presented device enabled a repeatable and accurate microwave response under UV illumination with very high sensitivity, entirely through the use of passive circuit elements.

Microwave resonator array with liquid metal selection for narrow band material sensing.

A microwave resonator array is integrated with liquid metal to select an individual resonator response within a resonator array, enabling simple and accurate analysis for dielectric sensing. Galinstan, a liquid metal, acts as a multiplexer by inducing a capacitive load to the nearby resonator, lowering its resonant frequency, and thereby isolating its resonant response from other resonators in the array. The liquid metal could be positioned within a fluidic channel to be above any of the resonators, which tuned the resonant frequency from 3.9 to 3.3 GHz where it can be analyzed individually. The resonators showed a consistent response to liquid metal tuning, with tuning error measured below 30 MHz (5%). The sensor also exhibited stable sensitivity to test materials placed on the selected resonator, with a maximum resonant frequency shift of 300 MHz for a dielectric test material (ε = 10.2) and almost no variation in resonant amplitude. The selected resonant response was only sensitive to materials on the selected resonator, and was unaffected by test materials, even when placed on other resonators. The presented design enabled robust and accurate detection of materials using planar microwave resonators that can be controlled at a user's convenience, specifically for use in systems where multiple parameters or system settings may need to be individually determined.

Oleophobic textiles with embedded liquid and vapor hazard detection using differential planar microwave resonators.

Protective clothing must repel hazardous liquids such as oils, acids, and solvents, which often exhibit low surface tension. The low surface tension liquid repellency of textiles is currently characterized qualitatively, considering only the first thirty seconds of wetting. This study demonstrates that embedded sensors within protective fabrics can more fully characterize liquid repellency while simultaneously detecting the hazardous substance. The liquid repellency of oleophobic textiles was detected in-situ using differential planar microwave resonator structures. A differential split ring resonator was designed with resonant responses at 4.4 and 4.6 GHz with a sensitivity of 50 MHz per unit ε. Fabrics were rendered oleophobic by dip-coating. The liquid repellency was monitored in-situ using droplets of heptane, octane, decane, dodecane, and water. Wetting transitions and droplet evaporation were identified in real time. The 4.4 GHz resonance peak's shift was used to measure the liquid repellency, whereas the 4.6 GHz resonator monitored the liquid's vapor as it absorbed into a gas-sensitive elastomer. The microwave response was tracked over 10 h every 15 s, and this transient data could identify the liquids based on their wetting and evaporation rates. Such sensors could be readily embedded in oleophobic textiles and enhance personal protective equipment.

Distinguishing between Deep Trapping Transients of Electrons and Holes in TiO2 Nanotube Arrays Using Planar Microwave Resonator Sensor.

A large signal direct current (DC) bias and a small signal microwave bias were simultaneously applied to TiO2 nanotube membranes mounted on a planar microwave resonator. The DC bias modulated the electron concentration in the TiO2 nanotubes and was varied between 0 and 120 V in this study. Transients immediately following the application and removal of DC bias were measured by monitoring the S-parameters of the resonator as a function of time. The DC bias stimulated Poole-Frenkel-type trap-mediated electrical injection of excess carriers into TiO2 nanotubes, which resulted in a near-constant resonant frequency but a pronounced decrease in the microwave amplitude due to free electron absorption. When ultraviolet illumination and DC bias were both present and then stepwise removed, the resonant frequency shifted due to trapping-mediated change in the dielectric constant of the nanotube membranes. Characteristic lifetimes of 60-80, 300-800, and ∼3000 s were present regardless of whether light or bias was applied and were also observed in the presence of a hole scavenger, which we attributed to oxygen adsorption and deep electron traps, whereas another characteristic lifetime >8000 s was only present when illumination was applied, and is attributed to the presence of hole traps.

Composition-Tunable Formamidinium Lead Mixed Halide Perovskites via Solvent-Free Mechanochemical Synthesis: Decoding the Pb Environments Using Solid-State NMR Spectroscopy.

Mixed-halide lead perovskites are becoming of paramount interest in the optoelectronic and photovoltaic research fields, offering band gap tunability, improved efficiency, and enhanced stability compared to their single halide counterparts. Formamidinium-based mixed halide perovskites (FA-MHPs) are critical to obtaining optimum solar cell performance. Here, we report a solvent-free mechanochemical synthesis (MCS) method to prepare FA-MHPs, starting with their parent compounds (FAPbX3; X = Cl, Br, I), achieving compositions not previously accessible through the solvent synthesis (SS) technique. By probing local Pb environments in MCS FA-MHPs using solid-state nuclear magnetic resonance spectroscopy, along with powder X-ray diffraction for long-range crystallinity and reflectance measurements to determine the optical band gap, we show that MCS FA-MHPs form atomic-level solid solutions between Cl/Br and Br/I MHPs. Our results pave the way for advanced methods in atomic-level structural understanding while offering a one-pot synthetic approach to prepare MHPs with superior control of stoichiometry.

Top-Down Approaches Towards Single Crystal Perovskite Solar Cells.

Solar cells employing hybrid perovskites have proven to be a serious contender versus established thin-film photovoltaic technologies. Typically, current photovoltaic devices are built up layer by layer from a transparent substrate (bottom-up approach), while the deposition of the perovskite layer itself comes with many challenges including the control of crystal size, nucleation density and growth rate. On the other hand, single crystals have been used with great success for studying the fundamental properties of this new class of optoelectronic materials. However, optoelectronic devices fabricated from single crystals often employ different materials than in their thin film counterparts. Here, we demonstrate various top-down approaches for low-temperature processed organic-inorganic metal halide perovskite single crystal devices. Our approach uses common and well-established material combinations that are often used in polycrystalline thin film devices. The use of a polymer bezel allows easier processing of small crystals and the fabrication of solution-processed, free-standing perovskite single crystal devices. All in all these approaches can supplement other measurements of more fundamental material properties often requiring perovskite single crystals by rendering a photovoltaic characterization possible on the very same crystal with comparable material combinations as in thin film devices.

Heterojunctions of mixed phase TiO2 nanotubes with Cu, CuPt, and Pt nanoparticles: interfacial band alignment and visible light photoelectrochemical activity.

Anodically formed, vertically oriented, self-organized cylindrical TiO2 nanotube arrays composed of the anatase phase undergo an interesting morphological and phase transition upon flame annealing to square-shaped nanotubes composed of both anatase and rutile phases. This is the first report on heterojunctions consisting of metal nanoparticles (NPs) deposited on square-shaped TiO2 nanotube arrays (STNAs) with mixed rutile and anatase phase content. A simple photochemical deposition process was used to form Cu, CuPt, and Pt NPs on the STNAs, and an enhancement in the visible light photoelectrochemical water splitting performance for the NP-decorated STNAs was observed over the bare STNAs. Under narrow band illumination by visible photons at 410 nm and 505 nm, Cu NP-decorated STNAs performed the best, producing photocurrents 80% higher and 50 times higher than bare STNAs, respectively. Probing the energy level structure at the NP-STNA interface using ultraviolet photoelectron spectroscopy revealed Schottky barrier formation in the NP-decorated STNAs, which assists in separating the photogenerated charge carriers, as also confirmed by longer charge carrier lifetimes in NP-decorated STNAs. While all the NP-decorated STNAs showed enhanced visible light absorption compared to the bare STNAs, only the Cu NPs exhibited a clear plasmonic behavior with an extinction cross section that peaked at 550 nm.

Halide perovskite solar cells using monocrystalline TiO2 nanorod arrays as electron transport layers: impact of nanorod morphology.

This is the first report of a 17.6% champion efficiency solar cell architecture comprising monocrystalline TiO2 nanorods (TNRs) coupled with perovskite, and formed using facile solution processing without non-routine surface conditioning. Vertically oriented TNR ensembles are desirable as electron transporting layers (ETLs) in halide perovskite solar cells (HPSCs) because of potential advantages such as vectorial electron percolation pathways to balance the longer hole diffusion lengths in certain halide perovskite semiconductors, ease of incorporating nanophotonic enhancements, and optimization between a high contact surface area for charge transfer (good) versus high interfacial recombination (bad). These advantages arise from the tunable morphology of hydrothermally grown rutile TNRs, which is a strong function of the growth conditions. Fluorescence lifetime imaging microscopy of the HPSCs demonstrated a stronger quenching of the perovskite PL when using TNRs as compared to mesoporous/compact TiO2 thin films. Due to increased interfacial contact area between the ETL and perovskite with easier pore filling, charge separation efficiency is dramatically enhanced. Additionally, solid-state impedance spectroscopy results strongly suggested the suppression of interfacial charge recombination between TNRs and perovskite layer, compared to other ETLs. The optimal ETL morphology in this study was found to consist of an array of TNRs ∼300 nm in length and ∼40 nm in width. This work highlights the potential of TNR ETLs to achieve high performance solution-processed HPSCs.

Reduced Ensemble Plasmon Line Widths and Enhanced Two-Photon Luminescence in Anodically Formed High Surface Area Au-TiO2 3D Nanocomposites.

Localized surface plasmon resonances (LSPR) in TiO2 nanorod and nanotube arrays decorated by gold nanoparticles can be exploited to improve photocatalytic activity, enhance nonlinear optical coefficients, and increase light harvesting in solar cells. However, the LSPR typically has a low quality factor, and the resonance is often obscured by the Urbach tail of the TiO2 band gap absorption. Attempts to increase the LSPR extinction intensity by increasing the density of gold nanoparticles on the surface of the TiO2 nanostructures invariably produce peak broadening due to the effects of either agglomeration or polydispersity. We present a new class of hybrid nanostructures containing gold nanoparticles (NPs) partially embedded in nanoporous/nanotubular TiO2 by performing the anodization of cosputtered Ti-Au thin films containing a relatively high ratio of Au:Ti. Our method of anodizing thin film stacks containing alternate layers of Ti and TiAu results in very distinctive LSPR peaks with quality factors as high as 6.9 and ensemble line widths as small as 0.33 eV even in the presence of an Urbach tail. Unusual features in the anodization of such films are observed and explained, including oscillatory current transients and the observation of coherent heterointerfaces between the Au NPs and anatase TiO2. We further show that such a plasmonic NP-embedded nanotube structure dramatically outperforms a plasmonic NP-decorated anodic nanotube structure in terms of the extinction coefficient, and achieves a strongly enhanced two-photon fluorescence due to the high density of gold nanoparticles in the composite film and the plasmonic local field enhancement.

Effect of phosphonate monolayer adsorbate on the microwave photoresponse of TiO2 nanotube membranes mounted on a planar double ring resonator.

In this study, the effects of a phosphonate molecular monolayer adsorbed on the surface of a free-standing self-organized TiO2 nanotube membrane, on the microwave photoresponse of the membrane are presented. This phenomenon is monitored using planar microwave sensors. A double ring resonator is utilized to monitor the permittivity and conductivity variation on the monolayer coated membrane and the sensor environment separately. It is shown that the rise time and subsequent decay of the amplitude (A), resonance frequency (f 0) and quality factor (Q) of the resonator depend on the existence and the type of the monolayer coating the membrane. Three different monolayers of n-decylphosphonic acid (DPA), 1H, 1H', 2H, 2H'-perfluorodecyl phosphonic acid (PFDPA) and 16-phosphonohexadecanoic acid adsorbed on the titania nanotube membrane are investigated while monitoring their microwave properties during the illumination time period and in the relaxation period, which demonstrate different behavior in comparison to each other and to the bare nanotube membrane layer. The effect of humidity on the TiO2 nanotube membrane with and without different monolayers is also studied and the results demonstrate distinguishable microwave responses. While each of the monolayer-coated membranes exhibited an attenuation of the photo-induced change in A, f 0 and Q with respect to the bare membrane, PFDPA-coated membranes showed the smallest relative change in the monitored microwave parameters upon ultraviolet illumination and upon the introduction of different levels of humidity. These effects are explained on the basis of surface trap passivation by the monolayers as well as the hydrophobicity of the monolayers. Our work also shows how the interactions of self-assembled monolayers with charge carriers and surface states on metal oxides may be used to indirectly sense their presence through measurement of the microwave response.

Rutile phase n- and p-type anodic titania nanotube arrays with square-shaped pore morphologies.

Rutile-phase TiO2 nanotube arrays without broken walls were formed by annealing of anodically formed nanotubes in a propane flame at 650 °C and in air at 750 °C. An unusual morphological transformation was observed from the ellipsoidal pore-shapes of titania nanotubes grown in aqueous electrolyte to a square-shaped pore structure subsequent to the anneals. 750 °C annealed nanotubes were found to be lightly p-type, rare in TiO2.

Phosphorescence within benzotellurophenes and color tunable tellurophenes under ambient conditions.

The zirconium-mediated syntheses of pinacolboronate (BPin) appended benzo[b]tellurophenes and two phenyl/BPin substituted tellurophene isomers with different colors of emission have been achieved. These species are new additions to an emerging class of inorganic heterocycles that display visible phosphorescence in the solid state under ambient conditions.