Examining the effectiveness of municipal street sweeping in removing road-deposited particles and metal(loid)s of respiratory health concern.

Road dust is a demonstrated source of urban air pollution. Given this, the implementation of street sweeping strategies that effectively limit road dust accumulation and resuspension should be a public health priority. Research examining the effectiveness of street sweeping for road dust removal in support of good air quality has been limited to date. To address this, the study aimed to assess the use of a regenerative-air street sweeper to efficiently remove road dust particles and metal(loid)s in size fractions relevant for respiratory exposure in Toronto, Canada. As part of this, the mass amounts, particle size distribution and elemental concentrations of bulk road dust before and after sweeping at five arterial sites were characterized. Sweeping reduced the total mass amount of thoracic-sized (<10 µm) road dust particles by 76 % on average. A shift in the size distribution of remaining particles toward finer fractions was observed in post-sweeping samples, together with an enrichment in many metal(loid)s such as Co, Ti and S. Overall, the mass amounts of metal(loid)s of respiratory health concern like Cu and Zn were greatly reduced with sweeping. Traffic volume and road surface quality were predictors of dust loadings and elemental concentrations. Road surface quality was also found to impact street sweeping efficiencies, with larger mass amounts per unit area collected post-sweeping where street surfaces were distressed. This study demonstrates that street sweeping using advanced technology can be highly effective for road dust removal, highlighting its potential to support air quality improvement efforts. The importance of tailoring sweeping service levels and technologies locally as per the quality of road surface and traffic patterns is emphasized. Continued efforts to mitigate non-exhaust emissions that pose a respiratory health risk at their source is essential.

Identification and quantification of trace metal(loid)s in water-extractable road dust nanoparticles using SP-ICP-MS.

Resuspension of road dust is a major source of airborne particulate matter (PM) in urban environments. Inhalation of ultrafine particles (UFP; < 0.1 µm) represents a health concern due to their ability to reach the alveoli and be translocated into the blood stream. It is therefore important to characterize chemical properties of UFPs associated with vehicle emissions. We investigated the capability of Single-Particle ICP-MS (SP-ICP-MS) to quantify key metal(loid)s in nanoparticles (NPs; < 0.1 µm) isolated from road dust collected in Toronto, Canada. Water extraction was performed to separate the <1-µm fraction from two different road dust samples (local road vs. arterial road) and a multi-element SP-ICP-MS analysis was then conducted on the samples' supernatants. Based on the particle number concentrations obtained for both supernatants, the metal(loid)-containing NPs could be grouped in the following categories: high (Cu and Zn, > 1.3 × 1011 particles/L), medium (V, Cr, Ba, Pb, Sb, Ce, La), low (As, Co, Ni, < 4.6 × 109 particles/L). The limit of detection for particle number concentration was below 5.5 × 106 particles/L for most elements, except for Cu, Co, Ni, Cr, and V (between 0.9 and 7.7 × 107 particles/L). The results demonstrate that road dust contains a wide range of readily mobilizable metal(loid)-bearing NPs and that NP numbers may vary as a function of road type. These findings have important implications for human health risk assessments in urban areas. Further research is needed, however, to comprehensively assess the NP content of road dust as influenced by various factors, including traffic volume and speed, fleet composition, and street sweeping frequency. The described method can quickly characterize multiple isotopes per sample in complex matrices, and offers the advantage of rapid sample scanning for the identification of NPs containing potentially toxic transition metal(loid)s at a low detection limit.

Characterizing the sources, concentrations and resuspension potential of metals and metalloids in the thoracic fraction of urban road dust.

Road dust is a sink and source of metals and metalloids of human health concern. To date, many studies have examined the composition of road dust but there remain critical knowledge gaps on the chemistry of thoracic fractions (< 10 µm) and their patterns of deposition and resuspension. The goal of this study is to characterize the elemental concentrations and sources of thoracic fractions of road dust and their resuspension potential for Toronto, Ontario, Canada. Bulk and thoracic road sweepings were acid digested (HF, HClO4, HNO3 and HCl) and the elemental concentrations measured using ICP-MS. Principal component analysis (PCA) was applied to infer source emissions. Annual elemental loadings to roads were estimated using data on total sweepings collected by the City of Toronto. The mass amounts of metals and metalloids (< 10 µm) available for resuspension were calculated assuming a contribution of 10% to total loadings for this fraction. The median trace element concentrations in city sweepings (n = 64) ranged from highest to lowest as follows: Mn > Zn > Ba > Cr > Cu > Pb > V > Ni > Sn > Mo > Co > As > Sb > Cd. Iron, Cr, Ni, Co, Mo and Cu levels were significantly associated with road class, with the highest concentrations measured for the expressway. Most elements, especially Sb and Zn, were enriched in thoracic sweepings. The PCA results demonstrate the importance of non-fossil fuel, traffic-related elemental emissions. Difficulties in identifying sources, given uncertainties regarding overlapping chemical profiles, are also highlighted. Significant elemental loadings to roads were estimated to occur, with the largest amounts identified for Fe, Al, Mn, Zn, Cr and Cu. Road dust resuspension is predicted to be the most important source of emissions for Fe, Al, Mn, Cr, V, Sn, Mo, Co and Sb.

An assessment of the inhalation bioaccessibility of platinum group elements in road dust using a simulated lung fluid.

Metal enrichment of road dust is well characterized but available data on the bioaccessibility of metals in particle size fractions relevant to human respiratory health remain limited. The study goal was to investigate the bioaccessibility of platinum group elements (PGE), which are used as catalysts in automotive exhaust converters, in the inhalable fraction of road dust. Street sweepings were provided by the City of Toronto, Canada, collected as part of its Clean Roads to Clean Air program.The particle size relevance of road dust for inhalation exposures was confirmed using a laser diffraction particle size analyzer (mean Dx(50): 9.42 µm). Total PGE were determined in both bulk and inhalable fractions using nickel sulfide (NiS) fire-assay and instrumental neutron-activation analysis (INAA). PGE lung solubility was examined for the inhalable fraction using Gamble's extraction. Sample digests were co-precipitated with Te-Sn, to pre-concentrate and isolate PGE, prior to their measurement using inductively coupled plasma mass spectrometry (ICP-MS).Total PGE concentrations were enriched in the inhalable fraction of road sweepings. Geomean concentrations in the inhalable fraction were: palladium (Pd) (152 µg/kg), platinum (Pt) (55 µg/kg), rhodium (Rh) (21 µg/kg) and iridium (Ir) (0.23 µg/kg). Osmium (Os) concentrations were below the limit of detection (LOD). Bioaccessible PGEs (n = 16) using Gamble's solution were below LOD for Ir and ruthenium (Ru). For the remainder, the geomean % bioaccessibility was highest for platinum (16%), followed by rhodium (14%) and palladium (3.4%). This study provides evidence that PGE in road dust are bioaccessible in the human lung.

Environmental factors associated with blood lead among newcomer women from South and East Asia in the Greater Toronto Area.

BACKGROUND: Newcomers bring with them histories of environmental exposure in their home countries and may have different sources of lead (Pb) exposure compared to other residents of their adopted country. AIMS: To describe past and current factors associated with Pb exposure and blood Pb among South and East Asian newcomer women of reproductive age in the Greater Toronto Area (GTA), Ontario, Canada. METHODS: In collaboration with public health units and community organizations a community-based research model was utilized by recruiting peer researchers to assist in all aspects of the study. Blood samples were taken and phone interviews were conducted. Canadian Health Measures Survey (CHMS) cycles 1, 2, and 3 data was used to contextualize the distribution blood Pb levels. Multiple regression was applied to log-transformed blood lead measurements, using a hierarchical model building process. RESULTS: In total, 211 participants were recruited from Bangladesh, China, India, Pakistan and Sri Lanka. The distribution of the blood Pb varied by country of origin, and higher blood Pb values were found above 75th percentile compared to the CHMS. Distal factors significantly influencing blood Pb concentrations related to life history, such as duration of stay in Canada (RR=0.91; 95% CI 0.86-0.97), living near agricultural fields (RR=0.78; 95% CI 0.62-0.93), and country of origin. Proximal factors with significant contribution were use of cosmetics, traditional remedies, and smoking cigarettes. RECOMMENDATIONS: Different past and current exposures may be important in various newcomer populations, informing international stakeholders, public health agencies, and primary care practitioners to adapt health education and exposure reduction programs to consider pre- and post-migration factors.

'Well, it literally stops me from having a life when it's really bad': a nested qualitative interview study of patient views on the use of self-management treatments for the management of recurrent sinusitis (SNIFS trial).

OBJECTIVE: To explore the experience and perceptions of illness, the decision to consult a general practitioner and the use of self-management approaches for chronic or recurrent sinusitis. DESIGN: Qualitative semistructured interview study. SETTING: UK primary care. PARTICIPANTS: 32 participants who had been participating in the 'SNIFS' (Steam inhalation and Nasal Irrigation For recurrent Sinusitis) trial in the South of England. METHOD: Thematic analysis of semistructured telephone interviews. RESULTS: Participants often reported dramatic impact on both activities and their quality of life. Participants were aware of both antibiotic side effects and resistance, but if they had previously been prescribed antibiotics, many patients believed that they would be necessary for the future treatment of sinusitis. Participants used self-help treatments for short and limited periods of time only. In the context of the trial, steam inhalation used for recurrent sinusitis was described as acceptable but is seen as having limited effectiveness. Nasal irrigation was viewed as acceptable and beneficial by more patients. However, some participants reported that they would not use the treatment again due to the uncomfortable side effects they experienced, which outweighed any symptom relief, which may have resulted had they continued. CONCLUSIONS: Steam inhalation is acceptable but seen as having limited effectiveness. Nasal irrigation is generally acceptable and beneficial for symptoms, but detailed information on the correct procedure and potential benefits of persisting may increase acceptability and adherence in those patients who find it uncomfortable. TRIAL REGISTRATION NUMBER: ISRCTN 88204146.

Metal Concentrations in Newcomer Women and Environmental Exposures: A Scoping Review.

Newcomer women from developing countries are recognized to be at risk for elevated exposures to environmental contaminants and associated negative health effects. As such, data on exposure sources and contaminant body burden concentrations is critical in the development of effective public health policies and interventions in support of newcomer health. We conducted a scoping review to gather evidence on important toxic metals of health concern, lead (Pb), mercury (Hg) and cadmium (Cd), and their concentrations and potential exposure sources among newcomer women. An initial 420 articles were identified through the databases MEDLINE, EMBASE and Scopus, many reporting by ethnicity rather than newcomer/immigrant status. Several articles reported metal concentrations for other biomarkers but did not include blood, nor stratify results. From the remainder, we selected a total of 10 articles for full textual review, which reported blood Pb, Hg or Cd levels for newcomer women and/or stratified blood metal results according to foreign birth or country of origin. Three of the articles reported higher Pb, Hg and Cd concentrations in newcomer women compared to their native-borne counterparts. Exposures identified as contributing to elevated Pb, Hg and Cd blood concentrations included: pica behaviour, the use of lead-glazed cookware or eye cosmetics, and fish/shellfish consumption. The review revealed a limited availability of data on metal body burden concentrations, exposure sources and routes among newcomer women specifically. More research is needed to better understand the extent to which newcomer women are disproportionately at risk of elevated metal exposures due to either country of origin or current exposures and to inform relevant, multi-national risk management strategies.

Assessing the potential of inorganic anions (Cl-, NO3-, SO42- and PO43-) to increase the bioaccessibility of emitted palladium in the environment: Experimental studies with soils and a Pd model substance.

Palladium (Pd) emitted from vehicles equipped with exhaust catalytic converters has been accumulating at a greater rate relative to other platinum group elements (PGE) in the last 10-20 years. Little is known, however, regarding the various environmental factors and conditions which are likely to modulate the chemical behavior and bioaccessibility of this element post-emission. To meet data needs, soils and a Pd model substance were treated with solutions containing common anions (Cl-, NO3-, SO42- und PO43-) to shed light on the geochemical behavior of emitted Pd under ambient conditions. As part of this, the particle surface chemistry of treated residues (insoluble phase) and solutions (soluble phase) was examined using XPS to assess the chemical transformation of Pd in the presence of inorganic anions. The results show that Pd is the most soluble in the presence of anionic species, followed by rhodium (Rh) and platinum (Pt). Pd in field-collected samples was found to be considerably more soluble than the metallic Pd in the model substance, Pd black, when treated with anionic species. The results also demonstrate that the solubility of Pd black is strongly dependent on solution pH, concentration and the duration of reaction. The outer 3-4 atomic layers of metallic Pd was determined via XPS to be partially oxidized when treated with anion solutions, with the degree being dependent on anion type. The concentration of dissolved O2 in solution was found to have little impact on the transformation of metallic Pd. Given the ubiquitous nature of the anions examined, we can expect that Pd will become more bioaccessible post-emission.

Platinum group element and cerium concentrations in roadside environments in Toronto, Canada.

Platinum (Pt), palladium (Pd) and rhodium (Rh) are accumulating globally in the environment, due to their use as catalysts to control automotive exhaust emissions. While environmental increases in platinum metal concentrations have been well documented for a number of countries, published data for Canada have been missing to date. The aim of this study is to examine the concentrations of Pt, Pd and Rh, as well as Ce, in soils and dust as a function of traffic volume in Toronto, Ontario. Soils and road and underpass dust were collected from two sites with medium and high volumes of traffic. Samples were acid digested and co-precipitated with Hg (for Pd) and Te (for Pt and Rh), prior to measurement using ICP-Q-MS. Palladium occurred at the highest levels in samples, followed by Pt and Rh. Median concentrations for all soil samples were 63 µg Pd/kg, 8.7 µg Pt/kg, 1.7 µg Rh/kg and 41 mg Ce/kg. The results support existing data regarding PGE accumulation trends in urban and roadside environments, due to their use as catalysts in automotive catalytic converters. This study also confirms a shift toward the heavier use of Pd as the catalyst of choice in recent years, as reflected in the higher concentrations measured for this metal relative to Pt and Rh. The results highlight a need to continue monitoring the accumulation of PGE, most notably Pd, in urban environments.

Geochemical behaviour of palladium in soils and Pd/PdO model substances in the presence of the organic complexing agents L-methionine and citric acid.

Risk assessments of platinum group metal (PGE) emissions, notably those of platinum (Pt), palladium (Pd) and rhodium (Rh), have been mostly based on data regarding the metallic forms used in vehicular exhaust converters, known to be virtually biologically inert and immobile. To adequately assess the potential impacts of PGE, however, data on the chemical behaviour of these metals under ambient conditions post-emission is needed. Complexing agents with a high affinity for metals in the environment are hypothesized to contribute to an increased bioaccessibility of PGE. The purpose of this study is to examine the modulating effects of the organic complexing agents, L-methionine and citric acid, on the geochemical behavior of Pd in soils and model substances (Pd black and PdO). Batch experimental tests were conducted with soils and model substances to examine the impacts of the concentration of complexing agents, pH and length of extraction period on Pd solubility and its chemical transformation. Particle surface chemistry was examined using X-ray photoelectron spectroscopy (XPS) on samples treated with solutions under various conditions, including low and high O2 levels. Pd was observed to be more soluble in the presence of organic complexing agents, compared to Pt and Rh. Pd in soils was more readily solubilized with organic complexing agents compared to the model substances. After 7 days of extraction, L-methionine (0.1 M) treated soil and Pd black samples, for instance, had mean soluble Pd fractions of 12.4 ± 5.9% and 0.554 ± 0.024%, respectively. Surface chemistry analyses (XPS) confirmed the oxidation of metallic Pd surfaces when treated with organic complexing agents. The type of organic complexing agent used for experimental purposes was observed to be the most important factor influencing solubility, followed by solution pH and time of extraction. The results demonstrate that metallic Pd can be transformed into more bioaccessible species in the presence of organic complexing agents which are ubiquitous in the environment.

Metal and metalloid accumulation in cultivated urban soils: A medium-term study of trends in Toronto, Canada.

This study aims to examine the elemental enrichment patterns in low to medium traffic areas over a three year period in Toronto, Canada. Soils were sampled at three locations with different volumes of traffic between 2010 and 2013. A range of elements, including V, Cr, Mn, Cu, Cd, As, Sb and Pb, were measured in acid digested samples using ICP-MS. While the concentrations of Cd, Sb and Pb were found to be relatively low, a significant, albeit small increase in their levels over time was determined for all sites. For the low traffic areas, median Cd, Sb and Pb concentrations increased from 0.18mg Cd/kg, 0.14mg Sb/kg and 12mg Pb/kg in 2010 to 0.38mg Cd/kg, 0.21mg Sb/kg and 15mg Pb/kg in 2012, respectively. For the medium traffic site, the respective levels of Cd and Sb rose from 0.19mg Cd/kg and 0.14mg Sb/kg in 2010 to 0.49mg Cd/kg and 0.28mg Sb/kg in 2012. Median Pb concentrations at the medium traffic site were comparable to those at the low traffic sites (13mg/kg in 2010 and 15mg/kg in 2012). Principal Component Analysis (PCA) revealed the existence of two components (rotated), which explained 77% of the variance for all sites: 1. PC1 with large loadings of V, Cr, Co and Cu that likely originate from the commercial soil originally used for monitoring purposes, and 2. PC2 with high correlations between Cd, Sb and Pb, attributed to traffic sources of emissions. The resuspension and transport of more mobile fractions of contaminated dust and soil particles is hypothesized to be contributing to an elemental enrichment of soils located in low traffic areas.

Analytical methods for assessing metal bioaccessibility in airborne particulate matter: A scoping review.

In contrast to the existence of standardized methods to assess metal bioaccessibility via the gastrointestinal route, there are no widely-accepted, established in vitro testing protocols to measure elemental solubility in the human lung. This may be attributed, in part, to the difficulty associated with simulating the lung's complex in vivo conditions. The purpose of this review is two-fold: (1) to determine how the bioaccessibility of metals associated with ambient particulate matter (PM) in the human lung has been assessed in the literature, and (2) examine the suitability and biological relevance of applied methods for the measurement of metal bioaccessibility employed to date. The review revealed that limited attention has been paid to the development and application of biologically-relevant in vitro methods to measure elemental solubility in ambient PM as a proxy for bioaccessibility in the human lung. Few studies (n=14) used synthetic lung fluids to simulate in vivo conditions, with only half extracting samples at a biologically-relevant temperature of 37°C. There was limited evidence suggesting that the use of water is less effective as a leaching agent compared to simulated lung fluids. In sum, this scoping review highlights a critical need to develop standardized methods for the systematic assessment of elemental bioaccessibility via the respiratory route. Priority should be placed on the validation of biologically-relevant methods, including the use of leaching agents and extraction parameters used, which allow for testing to be conducted in a reliable, yet cost efficient, manner.

The influence of ethylenediamine tetra acetic acid (EDTA) on the transformation and solubility of metallic palladium and palladium(II) oxide in the environment.

The environmental occurrence of elevated concentrations of platinum (Pt), palladium (Pd) and rhodium (Rh) from automotive catalytic converters has been well-documented. Limited information exists regarding their chemical behavior post-emission, however, especially in the presence of commonly occurring complexing agents. The purpose of this study is to examine the influence of ethylenediamine tetra acetic acid (EDTA) on the possible environmental transformation and solubility of Pd by conducting batch experiments using metallic palladium (Pd black) and palladium(ii) oxide (PdO). Changes in the particle surface chemistry of treated samples were analyzed using X-ray Photoelectron Spectroscopy (XPS) and Transition Electron Microscopy/Energy Dispersive X-ray Spectrometry (TEM/EDX) techniques. Metallic palladium was partially transformed into PdOx (x < 1), while PdO remained largely unaffected. The pH of EDTA solutions was observed to modulate Pd solubility, with Pd black demonstrating a higher solubility compared to PdO. Solubility was also found to increase with a corresponding increase in the strength of EDTA solution concentrations, as well as with the length of extraction time. The overall solubility of Pd remained relatively low for most samples (<1 wt%). A dissolution rate of 2.01 ± 0.17 nmol m(-2) h(-1) was calculated for Pd black in 0.1 M EDTA (pH 7). In contrast to previously held assumptions about the environmental immobility of Pd, small amounts of this element emitted in metallic form are likely to be soluble in the presence of complexing agents such as EDTA.

Metal translocation patterns in Solanum melongena grown in close proximity to traffic.

The purpose of this study is to examine tissue patterns of metal (Cr, Ni, Cu, Cd, and Pb) concentrations in Solanum melongena cultivated in close proximity to traffic to help elucidate associated elemental deposition and soil-to-root and root-to-shoot transfers. Plants were cultivated in a commercial soil mix at three sites in Toronto, Canada. Metal concentrations were determined on microwave-digested bulk and rhizosphere soil and tissue samples per ICP-MS, along with two standard reference materials (NIST #1570a and #2709a). Unwashed and washed S. melongena samples were also analyzed, along with Origanum vulgare plants from the same sites, to assess the effectiveness of washing in reducing metal concentrations. The tissue distribution of Cr, Ni, Cu, and Pb demonstrated variability as a function of traffic proximity. Copper was found to easily translocate to roots in soils susceptible to waterlogging, while Cd had the highest soil-to-root and root-to-shoot translocation. The translocation of Cd was highest at the roadside site, due to a greater relative enrichment of this metal in the rhizosphere of S. melongena plants. Washing O. vulgare leaves was more effective in removing metal-associated particles compared to S. melongena samples. Cadmium uptake is of greatest concern given its toxicity and translocation potential.

Differential environmental exposure among non-Indigenous Canadians as a function of sex/gender and race/ethnicity variables: a scoping review.

OBJECTIVES: To determine the extent, range and types of studies of differential environmental chemical exposures among non-Indigenous Canadians as a function of sex/gender and race/ethnicity. METHODS: Computerized database searches were performed from November to December 2013 using Medline, Embase, CAB Abstracts, Proquest and Scopus to identify relevant studies of environmental exposures among non-Indigenous adults aged ≥18 years in Canada published between 1993 and 2013. Articles were identified for full-text review based on a screening of titles and abstracts and were excluded during this initial review if they focused on environmental exposures in the following populations: 1) Indigenous populations, 2) individuals <15 years of age, 3) pregnant women and associated negative birth outcomes, or 4) non-Canadian populations. Articles were also excluded if the primary focus was on exposures to environmental tobacco smoke, non-chemical occupational hazards, infectious diseases, noise and/or radiation. A full-text review of 78 identified articles systematically assessed how sex/gender and race/ethnicity were considered. SYNTHESIS: Although 59% of studies stratified results by sex, less than half of these offered any explanation of differential exposures. Eighteen of the 78 studies (23%) used terms related to race/ethnicity in their participant descriptions. Of the studies that conducted subgroup analyses of exposure results by race/ethnicity (n=15), a total of 8 also included subgroup analysis by sex. Overall, 3 of the 78 (3%) articles reviewed analyzed environmental exposures as a function of sex/gender and race/ethnicity. CONCLUSION: The role of sex/gender and race/ethnicity in influencing environmental exposure levels among non-Indigenous Canadians has not been adequately addressed to date.

Traffic-related trace element fate and uptake by plants cultivated in roadside soils in Toronto, Canada.

This research examines traffic-related trace element emissions and their uptake by plants grown in urban roadside environments in Toronto, Canada. Oregano (Origanum vulgare), beets (Beta vulgaris) and eggplants (Solanum melongena) were cultivated at four locations with variable traffic-related metal inputs in 2010. The top 30 cm of soil at the medium-traffic location was first replaced with a triple mix soil (topsoil, compost and peat) to control for pre-existing contamination. The same soil was used to cultivate at the two no/low traffic locations. Soil at the heavy traffic location was not remediated. Soil, plant tissue and plant rhizosphere samples were collected for the analysis of a range of traffic-related metal(loids) using ICP-MS, including Cr, Mn, Cu, Ni, Cd, As, Sb and Pb. Samples were digested with HNO(3) and HCl using a microwave-assisted digestion procedure and then treated with HF prior to analysis. Two certified reference materials, San Joaquin soil (NIST 2709a) and trace elements in spinach leaves (NIST 1570a), were used for QA/QC purposes. Metal(loid) concentrations and accumulation over time were highly variable at the medium traffic site where the soil was replaced. Mn (p<0.10), As (p<0.10) and Sb (p<0.01) concentrations significantly increased in bulk soils from May to November 2010, while Ce (p<0.01) and Cd (p<0.10) levels decreased. For instance, median As concentrations increased from 4.39 to 8.40 mg/kg over this period. Metals were found to be more bioaccessible to O. vulgare grown in the new soil at the medium traffic volume site, compared to the aged soil at the heavy traffic location. Several elements, most notably Cd, were also found to accumulate in the root zone of sampled S. melongena. Metal concentrations in S. melongena rhizosphere were better predictors of plant tissue levels, providing evidence that soil quality guidelines based on total metal concentrations for bulk soils are inadequate.

In vitro investigations of platinum, palladium, and rhodium mobility in urban airborne particulate matter (PM10, PM2.5, and PM1) using simulated lung fluids.

Environmental concentrations of platinum group elements (PGE) have been increasing since the introduction of automotive catalytic converters to control harmful emissions. Assessments of the human health risks of exposures to these elements, especially through the inhalation of PGE-associated airborne particulate matter (PM), have been hampered by a lack of data on their bioaccessibility. The purpose of this study is to apply in vitro methods using simulated human lung fluids [artificial lysosomal fluid (ALF) and Gamble's solution] to assess the mobility of the PGE, platinum (Pt), palladium (Pd), and rhodium (Rh) in airborne PM of human health concern. Airborne PM samples (PM(10), PM(2.5), and PM(1)) were collected in Frankfurt am Main, Germany. For comparison, the same extraction experiments were conducted using the standard reference material, Used Auto Catalyst (monolith) (NIST 2557). Pt and Pd concentrations were measured using isotope dilution ICP-Q-MS, while Rh was measured directly with ICP-Q-MS (in collision mode with He), following established matrix separation and enrichment procedures, for both solid (filtered residues) and extracted sample phases. The mobilized fractions measured for PGE in PM(10), PM(2.5), and PM(1) were highly variable, which can be attributed to the heterogenic nature of airborne PM and its composition. Overall, the mobility of PGE in airborne PM samples was notable, with a mean of 51% Rh, 22% Pt, and 29% Pd present in PM(1) being mobilized by ALF after 24 h. For PM(1) exposed to Gamble's solution, a mean of 44% Rh, 18% Pt, and 17% Pd was measured in solution after 24 h. The mobility of PGE associated with airborne PM was also determined to be much higher compared to that measured for the auto catalyst standard reference material. The results suggest that PGE emitted from automotive catalytic converters are likely to undergo chemical transformations during and/or after being emitted in the environment. This study highlights the need to conduct bioaccessibility experiments using samples collected in the field to enable an adequate assessment of risk.

Platinum group elements (Pt, Pd, Rh) in airborne particulate matter in rural vs. urban areas of Germany: concentrations and spatial patterns of distribution.

This study examines platinum group element concentrations (PGE) (i.e. platinum (Pt), palladium (Pd) and rhodium (Rh)) and their spatial distribution in airborne particulate matter fractions (PM) of human health concern in urban and rural areas of Germany. Fractionated airborne dust and PM(10), PM(2.5) and PM(1) samples were collected along a busy road in Frankfurt am Main from July 2008 to April 2010. PM(10) was also sampled in Deuselbach and Neuglobsow between January 2008 and July 2009 to examine their concentrations at rural locations and potential for long-range transport. Pt, Pd and Rh were isolated and pre-enriched in samples using a combination of Te and Hg co-precipitation methods. Concentrations were determined using isotope dilution ICP-Q-MS (in collision mode with He). The highest airborne PGE concentrations were measured in PM(10) from Frankfurt (e.g. 12.4pg Pt/m(3) (mean)), while the rural locations of Deuselbach and Neuglobsow exhibited the lowest levels (e.g. 2pg Pt/m(3) (mean)). PGE concentrations were observed to decline with increasingly smaller PM size fractions from PM(10) to PM(1). All size fractions generally contained higher levels of Pd compared to Pt and Rh, an element of greater concern due to its solubility. PM(2.5) collected in Frankfurt had a mean of 16.1pg Pd/m(3), compared to 9.4pg/m(3) for Pt. PGE concentrations also demonstrated a distinct seasonal relationship, with the greatest levels occurring in winter. Compared to a previous study in 2002, PGE concentrations in fractionated airborne dust have significantly increased over time. Elevated PGE levels were also measured for PM(10) sampled in Neuglobsow and Deuselbach, which could not be attributed to local emission sources. Using the diagnostic meteorological model, CALMET, trajectory analyses confirmed our hypothesis that PGE are being transported over longer distances from other areas of Europe.

Children's health and environment education and training for health care professionals in Canada: assessing gaps, barriers, and needs.

Scientific evidence suggests that children may be especially vulnerable to environmental hazards. However, medical professionals are often unable to effectively diagnose and treat environment-related illness in patients. To rectify this, many have called for improved post-secondary education and training opportunities in this field in Canada. This study aims to assess the state of education and training for healthcare professionals in children's environment and health, identify related gaps and barriers, and develop recommendations for improvement. Survey participants indicated three primary barriers to the integration of children's health and environment topics in current curricula: a lack of available expertise in the discipline in Canada, a lack of perceived importance of the topic, and a lack of financial and institutional support. A concerted effort must be undertaken to overcome the identified barriers to produce a cadre of healthcare professionals skilled in children's health and environment.

Airborne particulate matter, platinum group elements and human health: a review of recent evidence.

Environmental concentrations of the platinum group elements (PGE) platinum (Pt), palladium (Pd) and rhodium (Rh) have been on the rise, due largely to the use of automobile catalytic converters which employ these metals as exhaust catalysts. It has generally been assumed that the health risks associated with environmental exposures to PGE are minimal. More recent studies on PGE toxicity, environmental bioavailability and concentrations in biologically relevant media indicate however that environmental exposures to these metals may indeed pose a health risk, especially at a chronic, subclinical level. The purpose of this paper is to review the most recent evidence and provide an up-to-date assessment of the risks related to environmental exposures of PGE, particularly in airborne particulate matter (PM). This review concludes that these metals may pose a greater health risk than once thought for several reasons. First, emitted PGE may be easily mobilised and solubilised by various compounds commonly present in the environment, thereby enhancing their bioavailability. Second, PGE may be transformed into more toxic species upon uptake by organisms. The presence of chloride in lung fluids, for instance, may lead to the formation of halogenated PGE complexes that have a greater potential to induce cellular damage. Third, a significant proportion of PGE found in airborne PM is present in the fine fraction that been found to be associated with increases in morbidity and mortality. PGE are also a concern to the extent that they contribute to the suite of metals found in fine PM suspected of eliciting a variety of health effects, especially in vulnerable populations. All these factors highlight the need to monitor environmental levels of PGE and continue research on their bioavailability, behaviour, speciation and associated toxicity to enable us to better assess their potential to elicit health effects in humans.