Effect of Anisotropy of Reduced Graphene Oxide on Thermal and Electrical Properties in Silicon Carbide Matrix Composites.

Reduced graphene oxide, due to its structure, exhibits anisotropic properties, which are particularly evident in electrical and thermal conductivity. This study focuses on examining the influence of reduced graphene oxide in silicon carbide on these properties in directions perpendicular and parallel to the direction of the aligned rGO flakes in produced composites. Reduced graphene oxide is characterized by very high in-plane thermal and electrical conductivity. It was observed that the addition of rGO increases thermal conductivity from 64 W/mK (reference sample) up to 98 W/mK for a SiC-3 wt.% rGO composite in the direction parallel to the rGO flakes. In the perpendicular direction, the values were slightly lower, reaching up to 84 W/mK. The difference observed in electrical conductivity values is more significant and is 1-2 orders of magnitude higher for the flakes' alignment direction. The measured electrical conductivity increased from 1.2710-8 S/m for the reference SiC sinter up to 1.55 × 10-5 S/m and 1.2410-4 S/m for the composites with 3 wt.% rGO for the perpendicular and parallel directions, respectively. This represents an enhancement of four orders of magnitude, with a clearly visible influence of the anisotropy of the rGO. The composite's enhanced electrical and thermal conductivity make it particularly attractive for electronic devices and high-power applications.

Synthesis of Ti3SiC2 Phases and Consolidation of MAX/SiC Composites-Microstructure and Mechanical Properties.

The article describes the Ti3SiC2 powder synthesis process. The influence of the molar ratio and two forms of carbon on the phase composition of the obtained powders was investigated. The synthesis was carried out using a spark plasma sintering (SPS) furnace. In addition, using the obtained powders, composites reinforced with SiC particles were produced. The obtained results showed no effect of the carbon form and a significant impact of annealing on the purity of the powders after synthesis. The composites were also consolidated using an SPS furnace at two temperatures of 1300 and 1400 °C. The tests showed low density and hardness for sinters from 1300 °C (maximum 3.97 g/cm3 and 447 HV5, respectively, for composite reinforced with 10% SiC). These parameters significantly increase for composites sintered at 1400 °C (maximum density 4.43 g/cm3 and hardness 1153 HV5, for Ti3AlC2-10% SiC). In addition, the crack propagation analysis showed mechanisms typical for granular materials and laminates.

Novel Alumina Matrix Composites Reinforced with MAX Phases-Microstructure Analysis and Mechanical Properties.

This article describes the manufacturing of alumina composites with the addition of titanium aluminum carbide Ti3AlC2, known as MAX phases. The composites were obtained by the powder metallurgy technique with three types of mill (horizontal mill, attritor mill, and planetary mill), and were consolidated with the use of the Spark Plasma Sintering method at 1400 °C, with dwelling time 10 min. The influence of the Ti3AlC2 MAX phase addition on the microstructure and mechanical properties of the obtained composites was analyzed. The structure of the MAX phase after the sintering process was also investigated. The chemical composition and phase composition analysis showed that the Ti3AlC2 addition preserved its structure after the sintering process. The increase in fracture toughness for all series of composites has been noted (over 20% compared to reference samples). Detailed stereological analysis of the obtained microstructures also could determine the influence of the applied mill on the homogeneity of the final microstructure and the properties of obtained composites.

Modelling and Characterisation of Residual Stress of SiC-Ti3C2Tx MXene Composites Sintered via Spark Plasma Sintering Method.

This article presents an attempt to determine the effect of the MXene phase addition and its decomposition during sintering with the use of the spark plasma sintering method on mechanical properties and residual stress of silicon carbide based composites. For this purpose, the unreinforced silicon carbide sinter and the silicon carbide composite with the addition of 2 wt.% of Ti3C2Tx were tested. The results showed a significant increase of fracture toughness and hardness for composite, respectively 36% and 13%. The numerical study involving this novel method of modelling shows the presence of a complex state of stress in the material, which is related to the anisotropic properties of graphitic carbon structures formed during sintering. An attempt to determine the actual values of residual stress in the tested materials using Raman spectroscopy was also made. These tests showed a good correlation with the constructed numerical model and confirmed the presence of a complex state of residual stress.

Association of Aneurysm Tissue Neutrophil Mediator Levels with Intraluminal Thrombus Thickness in Patients with Abdominal Aortic Aneurysm.

An intraluminal thrombus (ILT), which accumulates large numbers of neutrophils, plays a key role in abdominal aortic aneurysm (AAA) pathogenesis. This study aimed to compare levels of selected neutrophil inflammatory mediators in thick and thin ILT, plus adjacent AAA walls, to determine whether levels depend on ILT thickness. Neutrophil mediator levels were analysed by enzyme-linked immunosorbent assays in thick and thin segments of ILT, plus adjacent aneurysm wall sections, taken from one aneurysm sac each from 36 AAA patients. In aneurysmal walls covered by thick ILT, neutrophil elastase and TNF-a levels were significantly higher, as were concentrations of IL-6, in thick ILT compared to thin layers. Positive correlations of NGAL, MPO, and neutrophil elastase were observed between thick ILT and the adjacent wall and thin ILT and the adjacent wall, suggesting that these mediators probably infiltrate thick AAA compartments as well as thin. These observations might support the idea that neutrophil mediators and inflammatory cytokines differentially accumulate in AAA tissues according to ILT thickness. The increased levels of neutrophil mediators within thicker AAA segments might suggest the existence of an intensified proinflammatory state that in turn presumably might preferentially weaken the AAA wall at that region.

Investigation of MXenes Oxidation Process during SPS Method Annealing.

This paper discusses the effects of the environment and temperature of the Ti3C2 (MXene) oxidation process. The MXene powders were annealed at temperatures of 1000, 1200, 1400, 1600, and 1800 °C in argon and vacuum using a Spark Plasma Sintering (SPS) furnace. The purpose of the applied annealing method was to determine the influence of a high heating rate on the MXene degradation scheme. Additionally, to determine the thermal stability of MXene during the sintering of SiC matrix composites, SiC-C-B-Ti3C2 powder mixtures were also annealed. The process parameters were as follows: Temperatures of 1400 and 1600 °C, and pressure of 30 MPa in a vacuum. Observations of the microstructure showed that, due to annealing of the SiC-C-B-Ti3C2 powder mixtures, porous particles are formed consisting of TiC, Ti3C2sym, and amorphous carbon. The formation of porous particles is a transitional stage in the formation of disordered carbon structures.

Influence of Ti3C2Tx MXene and Surface-Modified Ti3C2Tx MXene Addition on Microstructure and Mechanical Properties of Silicon Carbide Composites Sintered via Spark Plasma Sintering Method.

This article presents new findings related to the problem of the introduction of MXene phases into the silicon carbide matrix. The addition of MXene phases, as shown by the latest research, can significantly improve the mechanical properties of silicon carbide, including fracture toughness. Low fracture toughness is one of the main disadvantages that significantly limit its use. As a part of the experiment, two series of composites were produced with the addition of 2D-Ti3C2Tx MXene and 2D-Ti3C2Tx surface-modified MXene with the use of the sol-gel method with a mixture of Y2O3/Al2O3 oxides. The composites were obtained with the powder metallurgy technique and sintered with the Spark Plasma Sintering method at 1900 °C. The effect adding MXene phases had on the mechanical properties and microstructure of the produced sinters was investigated. Moreover, the influence of the performed surface modification on changes in the properties of the produced composites was determined. The analysis of the obtained results showed that during sintering, the MXene phases oxidize with the formation of carbon flakes playing the role of reinforcement. The influence of the Y2O3/Al2O3 layer on the structure of carbon flakes and the higher quality of the interface was also demonstrated. This was reflected in the higher mechanical properties of composites with the addition of modified Ti3C2Tx. Composites with 1 wt.% addition of Ti3C2Tx M are characterized with a fracture toughness of 5 MPa × m0.5, which is over 50% higher than in the case of the reference sample and over 15% higher than for the composite with 2.5 wt.% addition of Ti3C2Tx, which showed the highest fracture toughness in this series.

Special Issue: New Findings of MXenes: Preparation, Properties and Applications in Biotechnology and Catalysis.

The discovery of graphene drove intensive studies towards novel two-dimensional (2D) materials [...].

Microstructure and Mechanical Properties of Alumina Composites with Addition of Structurally Modified 2D Ti3C2 (MXene) Phase.

This study presents new findings related to the incorporation of MXene phases into ceramic. Aluminium oxide and synthesised Ti3C2 were utilised as starting materials. Knowing the tendency of MXenes to oxidation and degradation, particularly at higher temperatures, structural modifications were proposed. They consisted of creating the metallic layer on the Ti3C2, by sputtering the titanium or molybdenum. To prepare the composites, powder metallurgy and spark plasma sintering (SPS) techniques were adopted. In order to evaluate the effectiveness of the applied modifications, the emphasis of the research was placed on microstructural analysis. In addition, the mechanical properties of the obtained sinters were examined. Observations revealed significant changes in the MXenes degradation process, from porous areas with TiC particles (for unmodified Ti3C2), to in situ creation of graphitic carbon (in the case of Ti3C2-Ti/Mo). Moreover, the fracture changed from purely intergranular to cracking with high participation of transgranular mode, analogously. In addition, the results obtained showed an improvement in the mechanical properties for composites with Ti/Mo modifications (an increase of 10% and 15% in hardness and fracture toughness respectively, for specimens with 0.5 wt.% Ti3C2-Mo). For unmodified Ti3C2, enormously cracked areas with spatters emerged during tests, making the measurements impossible to perform.

Filtration Materials Modified with 2D Nanocomposites-A New Perspective for Point-of-Use Water Treatment.

Point-of-use (POU) water treatment systems and devices play an essential role in limited access to sanitary safe water resources. The filtering materials applied in POU systems must effectively eliminate contaminants, be readily produced and stable, and avoid secondary contamination of the treated water. We report an innovative, 2D Ti3C2/Al2O3/Ag/Cu nanocomposite-modified filtration material with the application potential for POU water treatment. The material is characterized by improved filtration velocity relative to an unmodified reference material, effective elimination of microorganisms, and self-disinfecting potential, which afforded the collection of 99.6% of bacteria in the filter. The effect was obtained with nanocomposite levels as low as 1%. Surface oxidation of the modified material increased its antimicrobial efficiency. No secondary release of the nanocomposites into the filtrate was observed and confirmed the stability of the material and its suitability for practical application in water treatment.

Influence of MXene (Ti3C2) Phase Addition on the Microstructure and Mechanical Properties of Silicon Nitride Ceramics.

This paper discusses the influence of Ti3C2 (MXene) addition on silicon nitride and its impact on the microstructure and mechanical properties of the latter. Composites were prepared through powder processing and sintered using the spark plasma sintering (SPS) technic. Relative density, hardness and fracture toughness, were analyzed. The highest fracture toughness at 5.3 MPa·m1/2 and the highest hardness at HV5 2217 were achieved for 0.7 and 2 wt.% Ti3C2, respectively. Moreover, the formation of the Si2N2O phase was observed as a result of both the MXene addition and the preservation of the α-Si3N4→ß-Si3N4 phase transformation during the sintering process.

Controlling the Porosity and Biocidal Properties of the Chitosan-Hyaluronate Matrix Hydrogel Nanocomposites by the Addition of 2D Ti3C2Tx MXene.

A recent discovery of the unique biological properties of two-dimensional transition metal carbides (MXenes) resulted in intensive research on their application in various biotechnological areas, including polymeric nanocomposite systems. However, the true potential of MXene as an additive to bioactive natural porous composite structures has yet to be fully explored. Here, we report that the addition of 2D Ti3C2Tx MXene by reducing the porosity of the chitosan-hyaluronate matrix nanocomposite structures, stabilized by vitamin C, maintains their desired antibacterial properties. This was confirmed by micro computed tomography (micro-CT) visualization which enables insight into the porous structure of nanocomposites. It was also found that given large porosity of the nanocomposite a small amount of MXene (1-5 wt.%) was effective against gram-negative Escherichia coli, gram-positive Staphylococcus aureus, and Bacillus sp. bacteria in a hydrogel system. Such an approach unequivocally advances the future design approaches of modern wound healing dressing materials with the addition of MXenes.

Engineering of 2D Ti3C2 MXene Surface Charge and Its Influence on Biological Properties.

Current trends in the field of MXenes emphasize the importance of controlling their surface features for successful application in biotechnological areas. The ability to stabilize the surface properties of MXenes has been demonstrated here through surface charge engineering. It was thus determined how changing the surface charges of two-dimensional (2D) Ti3C2 MXene phase flakes using cationic polymeric poly-L-lysine (PLL) molecules affects the colloidal and biological properties of the resulting hybrid 2D nanomaterial. Electrostatic adsorption of PLL on the surface of delaminated 2D Ti3C2 flakes occurs efficiently, leads to changing an MXene's negative surface charge toward a positive value, which can also be effectively managed through pH changes. Analysis of bioactive properties revealed additional antibacterial functionality of the developed 2D Ti3C2/PLL MXene flakes concerning Escherichia. coli Gram-negative bacteria cells. A reduction of two orders of magnitude of viable cells was achieved at a concentration of 200 mg L-1. The in vitro analysis also showed lowered toxicity in the concentration range up to 375 mg L-1. The presented study demonstrates a feasible approach to control surface properties of 2D Ti3C2 MXene flakes through surface charge engineering which was also verified in vitro for usage in biotechnology or nanomedicine applications.

The circadian rhythm of selected parameters of the hemostasis system in healthy people.

In this paper we tested a group of 66 healthy volunteers in terms of the influence of circadian rhythm on selected parameters of the coagulation system and fibrinolytic system. Blood was collected at 6-hour intervals, at 8 am, 2 pm, 8 pm and 2 am. Circadian variability was observed in the coagulation system parameters as well as in the fibrinolytic system. We observed increased platelet aggregation, APTT prolongation, along with increased levels of factors (fibrinogen, PAI-1) and PAP and TAT complexes that influence coagulation and fibrinolysis systems, in the blood samples collected in the morning (8 am). We also demonstrated a circadian rhythm in the number of circulating platelets (PLT), with a peak in the afternoon (2 pm) accompanied by increased concentrations of t-PA, D-dimers and PT prolongation. Based on the obtained results it was possible to conclude that circadian rhythm had an influence on the activation of coagulation processes in the morning, with a progressive activation of fibrinolysis up to the afternoon. Our results may be helpful in determining the transient risk of cardiovascular events, including myocardial infarction and ischemic stroke, and hence, can contribute to the effective prevention of such events. Such observations may also become a starting point of departure for further studies aimed at determining the circadian effect of secretion of parameters in the hemostasis system on the other systems and parameters in the human body.

Oculomotor dynamics in skilled soccer players: The effects of sport expertise and strenuous physical effort.

The ability to quickly locate objects within the visual field has a significant influence on athletic performance. Saccades are conjugate eye movements responsible for the rapid shift that brings a new part of the visual field into foveal vision. The aim of this study was to investigate the effects of sport expertise and intense physical effort on saccade dynamics during a free-viewing visual search task in skilled soccer players. Two groups of male subjects participated in this study: 18 soccer players and 18 non-athletes as the control group. Two sessions of visual search tasks without a sport-specific design were employed. Eye movements during the visual search tasks were recorded binocularly. Between pre- and post-test sessions, athletes performed a maximal incremental treadmill test. Cardiorespiratory parameters were measured continuously. Capillary lactate samples were collected. Pre-test findings indicated that athletes, in comparison to non-athletes, achieve higher values of the following characteristics of saccades (1) average acceleration, (2) acceleration peak, (3) deceleration peak, and (4) average velocity. An increase in post-test saccade duration and a decrease in post-test saccade velocity was observed in athletes due to the strenuous physical effort in relation to the pre-test state. Athletes may transfer high saccadic function efficiency to non-specific visual stimuli. The findings partially confirm that physical exertion can reduce oculomotor efficiency in athletes.

A Circadian Rhythm in both Complement Cascade (ComC) Activation and Sphingosine-1-Phosphate (S1P) Levels in Human Peripheral Blood Supports a Role for the ComC-S1P Axis in Circadian Changes in the Number of Stem Cells Circulating in Peripheral Blood.

The number of hematopoietic stem/progenitor cells (HSPCs) circulating in peripheral blood (PB) is regulated by a circadian rhythm, and more HSPCs circulate in PB in the morning hours than at night. Different mechanisms have been proposed that might regulate this process, including changes in tonus of ß-adrenergic innervation of bone marrow (BM) tissue. Our group reported that in mice circadian changes in the number of HSPCs circulating in PB correlates with diurnal activation of the complement cascade (ComC) and that the mice deficient in C5 component of ComC (C5-KO mice) do not show circadian changes in the number of circulating HSPCs in PB. We also reported the existence of a gradient between PB and BM of a bioactive phosphosphingolipid, sphingosine-1-phosphate (S1P), which is a major PB chemottractant for BM-residing HSPCs. Based on these observations, we investigated activation of the ComC and the level of S1P in the PB of 66 healthy volunteers. We found that both ComC activation and the S1P level undergo changes in a circadian cycle. While the ComC becomes highly activated during deep sleep at 2 am, S1P becomes activated later, and its highest level is observed at 8 am, which precedes circadian egress of HSPCs from BM into PB. In sum, circadian activation of the ComC-S1P axis releases HSPCs from BM into PB.

Closed Die Upsetting of Aluminum Matrix Composites Reinforced with Molybdenum Disulfide Nanocrystals and Multilayer Graphene, Implemented using the SPS Process-Microstructure Evolution.

New methods for producing composite materials such as SPS (Spark Plasma Sintering) are becoming more and more popular due to the ease of implementation in industrial conditions and the versatility of the materials used for processing. In order to fully exploit the potential of this method, modifications were proposed which consisted in the deliberate induction of deformation during the sintering process. The influence of the manufacturing method on the microstructure of aluminum alloy matrix composites reinforced with layered crystals in the form of nanoflakes was investigated. Composites with the addition of 10 vol % of multilayer graphene and molybdenum disulfide were prepared and their density, hardness, and the influence of the deformation ratio on the changes occurring in the microstructure were examined. The potential of the method to shape the properties of the tested composites and the strong dependence of the obtained results on the morphology of the reinforcing phase was indicated. An interesting phenomenon observed for composites with the addition of MoS2 during the process was the reaction of the components leading to in situ formation of the Al12Mo intermetallic phase.

Visual control in basketball shooting under exertion conditions.

BACKGROUND: This study examined the effect of physical exertion on gaze behavior during basketball shooting in both stationary and dynamic conditions. METHODS: Thirteen skilled basketball players performed two-point shooting during a 60 second fatigue protocol. Before and after a jump shot test, players performed two free throws. Eye movements were registered using an SMI Mobile EyeTracker. The frequency of all fixation points (number) and fixation duration during the motor phases of shooting were determined using frame-by-frame analysis. RESULTS: The type of basketball shot differentiated gaze control: 1) fixations were longer and more frequent during free throws as compared to jump shots; 2) shooting accuracy was positively influenced by less frequent and longer fixations; 3) physical exertion resulted in significantly more frequent fixations during free throws; and 4) exertion conditions resulted in a high variation in the patterns of total fixation times during jump shots. CONCLUSIONS: The findings suggest that physical exertion may reduce oculomotor efficiency during aiming at a distant target. Moreover, stationary and dynamic shots require different gaze behavior strategies.

Tribological Properties of Aluminium Alloy Composites Reinforced with Multi-Layer Graphene-The Influence of Spark Plasma Texturing Process.

Self-lubricating composites are designed to obtain materials that reduce energy consumption, improve heat dissipation between moving bodies, and eliminate the need for external lubricants. The use of a solid lubricant in bulk composite material always involves a significant reduction in its mechanical properties, which is usually not an optimal solution. The growing interest in multilayer graphene (MLG), characterised by interesting properties as a component of composites, encouraged the authors to use it as an alternative solid lubricant in aluminium matrix composites instead of graphite. Aluminium alloy 6061 matrix composite reinforced with 2-15 vol % of MLG were synthesised by the spark plasma sintering process (SPS) and its modification, spark plasma texturing (SPT), involving deformation of the pre-sintered body in a larger diameter matrix. It was found that the application of the SPT method improves the density and hardness of the composites, resulting in improved tribological properties, particularly in the higher load regime.

The Effects of Sports Vision Training on Binocular Vision Function in Female University Athletes.

Binocular vision is the most important visual cue for spatial orientation in many sports. In this study, we investigated how binocular vision was influenced by an eye training program that may be used to improve individual's oculomotor function. The experiment involved twenty-four female student athletes from team ball sports (soccer, basketball, handball). After an initial testing session, 12 participants were randomly allocated to the experimental group. Optometric investigation which included synoptophore testing and a test of dissociated horizontal phoria based on the Maddox method was performed three times: before the experiment, after eight weeks of eye training (3 times a week for 20 minutes), and four weeks after the experiment was terminated. Eye exercise methodology was based on orthoptic, sport and psychological aspects of performance. The phoria screening examination showed that exophoria was the most frequent disorder of binocular vision. Low fusional vergence range was also observed. Following the training period, 3 of the 6 oculomotor variables improved. The greatest effect was observed in near dissociated phoria (χ(2) =14.56, p=0.001 for the right eye; χ(2) =14.757, p=0.001 for the left eye) and fusional convergence (χ(2) =8.522, p=0.014). The results of the retention test conducted four weeks after the experiment confirmed the effectiveness of the vision training program. The results of the study suggest that binocular functions are trainable and can be improved by means of appropriate visual training.