Changes in Bone Mineral Density and Related Influencing Factors Assessed by Quantitative Computed Tomography in Maintenance Dialysis Patients.

OBJECTIVE: To investigate the changes in volumetric bone mineral density (vBMD) assessed by quantitative computed tomography (QCT) in chronic kidney disease (CKD) patients on maintenance dialysis. STUDY DESIGN: Descriptive study. Place and Duration of the Study: Department of Radiology, The Second Affiliated Hospital of Anhui Medical University, Hefei, China, from March to July 2022. METHODOLOGY: Maintenance dialysis patients were selected for this study, and parameters related to renal function and bone metabolism markers were recorded. Patients undergoing routine physical examination were age-matched with maintenance dialysis patients to serve as the control group. vBMD scans of the lumbar spine (L1-3) were obtained by QCT for all participants. RESULTS: Among the 141 maintenance dialysis patients, there were 67 patients with secondary hyperparathyroidism (SHPT) and 74 patients with non-secondary hyperparathyroidism (non-SHPT) with mean vBMDs of 145.99±55.13 mg/cm3 and 129.10±44.20 mg/cm3, respectively. The 159 individuals in the control group had mean age of 52.77±11.66 years and mean vBMD of 129.62±36.36 mg/cm3. The vBMD of the SHPT group was greater than that of both the non-SHPT group and the control group (all p<0.05). For dialysis patients, vBMD was positively correlated with calcium-phosphorus product and intact parathyroid hormone (iPTH) levels (r = 0.181, 0.214, respectively, p<0.05); vBMD was inversely correlated with age (r = -0.555, p<0.05). After adjusting for the covariates, vBMD remained positively correlated with iPTH (r = 0.184, p<0.05). CONCLUSION: Increased lumbar vertebral vBMD in maintenance dialysis patients may be associated with high iPTH, providing clinicians with a new understanding of the changes in bone mineral density in maintenance dialysis patients. KEY WORDS: Bone mineral density, Quantitative computed tomography, Chronic kidney disease, Maintenance dialysis.

Simultaneous Detection of Eight Prohibited Flavor Compounds in Foodstuffs Using Gas Chromatography-Tandem Mass Spectrometry.

A multiflavor detection method, using gas chromatography-triple quadrupole tandem mass spectrometry (GC-MS/MS), has been developed for the simultaneous identification and quantification of eight prohibited flavor compounds in daily foods. Under the optimized extraction conditions, samples were purified directly through membrane filtration. Variables affecting the GC-MS/MS were optimized to obtain better separation. The excellent selectivity and sensitivity achieved in multiple reactions monitoring mode allowed satisfactory confirmation and quantitation. In this study, the linear ranges of the target compounds were 0.05 to 500 ng/L with good correlation coefficients ( R2 > 0.999). The limits of detection of target compounds ranged from 0.005 to 0.2 µg/kg. The average recoveries were in the range of 80.2 to 110.6% (beef jerky), 82.3 to 94.1% (cod liver oil), and 83.6 to 104.1% (candy).

A high-throughput screening method of bisphenols, bisphenols digycidyl ethers and their derivatives in dairy products by ultra-high performance liquid chromatography-tandem mass spectrometry.

A simple and universal analytical method based on ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) for high throughput screening of 21 bisphenols, bisphenols digycidyl ethers and their derivatives in dairy products was developed. Response Surface Methodology (RSM) was used to optimize sample preparation conditions based on a quick, easy, cheap, effective, rugged and safe (QuEChERS) method. The analytes were extracted by using 15 mL acetonitrile with 1% acetic acid, and the extracts were further purified by using 190 mg of C18 and 390 mg of PSA. The extracts were analyzed by UHPLC-MS/MS with electrospray ionization (ESI) source. Linearity was assessed by using matrix-matched standard calibration and good correlation coefficients (r2 > 0.99) were obtained. The limits of quantitation (LOQs) for the analytes ranged from 0.02 to 5 µg kg-1. The extraction recoveries were in a range of 88.2%-108.2%. Good method reproducibility in terms of intra- and inter-day precision was observed, yielding relative standard deviations (RSDs) less than 8.9% and 9.9%, respectively. The validation method results revealed that the proposed method was sensitive and reliable. Finally, this method was successfully applied to dairy product analysis.