Effects of Inhomogeneous Gas Diffusion Layer Properties on the Transportation Phenomenon and Performances of Proton-Exchange Membrane Fuel Cells.

The encapsulation of the proton-exchange membrane fuel cell (PEMFC) is an essential step of fuel cell stack assembly. The selection of the assembly pressure is very important to the stack performance and life. Based on that, this paper presents a method to describe the internal physical deformation of the gas diffusion layer (GDL) after inhomogeneous pressure by using user-defined functions (UDFs). The results show that the transmission difference caused by the nonuniform GDL deformation can be clearly seen by the UDFs method, and there is an obvious transition of GDL at the interface of the channel and the rib. A three-dimensional single-channel PEMFC model is established, and an optimal assembly pressure range is obtained, between 1.5 and 2.0 MPa. The maximum thermal stress inside the cell occurs in the middle of the membrane electrode assembly and decreases as the assembly pressure increases. Furthermore, the influence of rib-channel ratios is discussed. Compared to the fuel cells with ratios of 2:1, 2:3, and 1:2, the one with 1:1 exhibits the maximum current density and the highest power density.

Water Management Capacity of Metal Foam Flow Field for PEMFC under Flooding Situation.

Porous metal foam with complex opening geometry has been used as a flow field to enhance the distribution of reactant gas and the removal of water in polymer electrolyte membrane fuel cells. In this study, the water management capacity of a metal foam flow field is experimentally investigated by polarization curve tests and electrochemical impedance spectroscopy measurements. Additionally, the dynamic behavior of water at the cathode and anode under various flooding situations is examined. It is found that obvious flooding phenomena are observed after water addition both into the anode and cathode, which are alleviated during a constant-potential test at 0.6 V. Greater abilities of anti-flooding and mass transfer and higher current densities are found as the same amount of water is added at the anode. No diffusion loop is depicted in the impedance plots although a 58.3% flow volume is occupied by water. The maximum current density of 1.0 A cm-2 and the lowest Rct around 17 mΩ cm2 are obtained at the optimum state after 40 and 50 min of operation as 2.0 and 2.5 g of water are added, respectively. The porous metal pores store a certain amount of water to humidify the membrane and achieve an internal "self-humidification" function.

Enhanced Ageing Performance of Sulfonic Acid-Grafted Pt/C Catalysts.

Chemical functionalization of carbon support for Pt catalysts is a promising way to enhance the performance of catalysts. In this study, Pt/C catalysts grafted with various amounts of phenylsulfonic acid groups were prepared under mild conditions. The influence of sulfonic acid groups on the physiochemical characteristics and electrochemical activities of the modified catalysts were studied using X-ray diffraction, X-ray photoelectron spectroscopy, a transmission electron microscope, and cyclic voltammetry (CV). The presence of the chemical groups enhanced the hydrogen adsorption onto/desorption off the Pt surface during the CV cycling. In contrast, the hydrogen peaks of the grafted catalysts increased after 500 CV cycles, especially for Pt (111) facets. The highest electrochemical surface area (ECSA) after the aging test was obtained for the catalyst with 18.0 wt.% graft, which was ca. 87.3% higher than that of the non-functionalized Pt catalyst. In the density functional theory (DFT) calculation, it was proven that SO3H adsorption on the crystalline was beneficial for Pt stability. The adsorption energy and bond distance of the adsorbed SO3H on Pt (110), (100), and (111) surfaces were calculated. All the stable configurations were obtained when O from S-O single bond or S was bound to the Pt surface, with the adsorption energy following the trend of (111)F > (100)H > (110)H. This result was consistent with the ECSA experiment, which explained the high electrochemical stability of the sulfonic acid groups-grafted Pt/C catalyst.

Time-course relationship between environmental factors and microbial diversity in tobacco soil.

Soil physicochemical properties and microbial diversity both play equally important roles in tobacco cultivation. However, the relationship between these factors remains unclear. In this study, we investigated their correlations through the whole tobacco growth period, including the pretransplanting (YX-p), root extending (R), flourishing (F), and mature (M) stages in the Yuxi region of the Yunnan-Guizhou Plateau by measuring physicochemical properties and conducting 16S/18S rRNA analysis. The analysis demonstrated that the microbial community richness and diversity continuously changed along with the growth course of the tobacco. Multiple environmental factors showed a certain correlation with the diversity of microbial communities. Some bacteria could accumulate nitrogen during the growth stages, and the diversity of the bacterial community also increased when the content of organic matter rose. In addition, the water content and available K also influenced the diversity of the microbial community. The dynamic changes in soil physicochemical properties and enzyme activities gave rise to differences in the microbial community composition and structure, all of which affected the growth of tobacco. This study revealed the time-course relationship between environmental factors and microbial diversity in tobacco soil. An understanding of this relationship provides guidance for research on the interaction system of plants, soil and microbes and on improving plant yield and quality.