Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 4 de 4
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
Molecules ; 27(18)2022 Sep 13.
Artigo em Inglês | MEDLINE | ID: mdl-36144683

RESUMO

Starch is a biocompatible and economical biopolymer in which interest has been shown in obtaining electrospun fibers. This research reports that cassava (CEX) and pea (PEX) starches pretreated by means of reactive extrusion (REX) improved the starches rheological properties and the availability of amylose to obtain fibers. Solutions of CEX and PEX (30-36% w/v) in 38% v/v formic acid were prepared and the rheological properties and electrospinability were studied. The rheological values indicated that to obtain continuous fibers without beads, the entanglement concentration (Ce) must be 1.20 and 1.25 times the concentration of CEX and PEX, respectively. In CEX, a higher amylose content and lower viscosity were obtained than in PEX, which resulted in a greater range of concentrations (32-36% w/v) to obtain continuous fibers without beads with average diameters ranging from 316 ± 65 nm to 394 ± 102 nm. In PEX, continuous fibers without beads were obtained only at 34% w/v with an average diameter of 170 ± 49 nm. This study showed that starches (20-35% amylose) pretreated through REX exhibited electrospinning properties to obtain fibers, opening the opportunity to expand their use in food, environmental, biosensor, and biomedical applications, as vehicles for the administration of bioactive compounds.


Assuntos
Manihot , Amilose , Pisum sativum , Amido , Viscosidade
2.
Polymers (Basel) ; 12(9)2020 Sep 01.
Artigo em Inglês | MEDLINE | ID: mdl-32882974

RESUMO

The aim of this work is to structurally characterize chitosan-zinc oxide nanoparticles (CS-ZnO NPs) films in a wide range of NPs concentration (0-20 wt.%). Dielectric, conductivity, mechanical, and piezoelectric properties are assessed by using thermogravimetry, FTIR, XRD, mechanical, and dielectric spectroscopy measurements. These analyses reveal that the dielectric constant, Young's modulus, and piezoelectric constant (d33) exhibit a strong dependence on nanoparticle concentration such that maximum values of referred properties are obtained at 15 wt.% of ZnO NPs. The piezoelectric coefficient d33 in CS-ZnO nanocomposite films with 15 wt.% of NPs (d33 = 65.9 pC/N) is higher than most of polymer-ZnO nanocomposites because of the synergistic effect of piezoelectricity of NPs, elastic properties of CS, and optimum NPs concentration. A three-phase model is used to include the chitosan matrix, ZnO NPs, and interfacial layer with dielectric constant higher than that of neat chitosan and ZnO. This layer between nanoparticles and matrix is due to strong interactions between chitosan's side groups with ZnO NPs. The understanding of nanoscale properties of CS-ZnO nanocomposites is important in the development of biocompatible sensors, actuators, nanogenerators for flexible electronics and biomedical applications.

3.
Colloids Surf B Biointerfaces ; 196: 111296, 2020 Dec.
Artigo em Inglês | MEDLINE | ID: mdl-32771819

RESUMO

Herein we report the synthesis of a piezopolymer composed of chitosan (CS)/hydroxylated BaTiO3 (OH-BTO) nanoparticles with enhanced biocompatibility, non-toxicity, and piezoelectric behavior that can be advantageously used in biomedical applications. Our CS/OH-BTO nanocomposites exhibit piezoelectric coefficient (d33 = 11.29 pC/N) between those of dry skin (0.05-0.19 pC/N) and bone (4-11 pC/N), demonstrating biocompatibility in contact with human fibroblasts (HF) cells after 24 h. SEM, XRD, FTIR and Raman measurements were performed to assess the mechanism of interaction between CS matrix and OH-BTO NPs and their correlation with the biological responses. Cytotoxicity assays with HF cells reveal that hydroxylation of BTO NPs does not affect the cell viability of CS/OH-BTO films with NPs concentration from 1 to 30 wt.%. In contrast, non-hydroxylated BTO NPs showed significant cell damage, which could be traced to uncontrollable NPs agglomeration. This behavior suggests that CS/OH-BTO nanocomposites can act as active material that promotes cell growth and can be used for biomedical purposes.


Assuntos
Quitosana , Antibacterianos , Compostos de Bário , Humanos , Engenharia Tecidual , Titânio
4.
Beilstein J Nanotechnol ; 11: 703-716, 2020.
Artigo em Inglês | MEDLINE | ID: mdl-32461872

RESUMO

In this work, a high-resolution atomic force acoustic microscopy imaging technique is developed in order to obtain the local indentation modulus at the nanoscale level. The technique uses a model that gives a qualitative relationship between a set of contact resonance frequencies and the indentation modulus. It is based on white-noise excitation of the tip-sample interaction and uses system theory for the extraction of the resonance modes. During conventional scanning, for each pixel, the tip-sample interaction is excited with a white-noise signal. Then, a fast Fourier transform is applied to the deflection signal that comes from the photodiodes of the atomic force microscopy (AFM) equipment. This approach allows for the measurement of several vibrational modes in a single step with high frequency resolution, with less computational cost and at a faster speed than other similar techniques. This technique is referred to as stochastic atomic force acoustic microscopy (S-AFAM), and the frequency shifts of the free resonance frequencies of an AFM cantilever are used to determine the mechanical properties of a material. S-AFAM is implemented and compared with a conventional technique (resonance tracking-atomic force acoustic microscopy, RT-AFAM). A sample of a graphite film on a glass substrate is analyzed. S-AFAM can be implemented in any AFM system due to its reduced instrumentation requirements compared to conventional techniques.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...