Soft elasticity optimises dissipation in 3D-printed liquid crystal elastomers.

Soft-elasticity in monodomain liquid crystal elastomers (LCEs) is promising for impact-absorbing applications where strain energy is ideally absorbed at constant stress. Conventionally, compressive and impact studies on LCEs have not been performed given the notorious difficulty synthesizing sufficiently large monodomain devices. Here, we use direct-ink writing 3D printing to fabricate bulk (>cm3) monodomain LCE devices and study their compressive soft-elasticity over 8 decades of strain rate. At quasi-static rates, the monodomain soft-elastic LCE dissipated 45% of strain energy while comparator materials dissipated less than 20%. At strain rates up to 3000 s-1, our soft-elastic monodomain LCE consistently performed closest to an ideal-impact absorber. Drop testing reveals soft-elasticity as a likely mechanism for effectively reducing the severity of impacts - with soft elastic LCEs offering a Gadd Severity Index 40% lower than a comparable isotropic elastomer. Lastly, we demonstrate tailoring deformation and buckling behavior in monodomain LCEs via the printed director orientation.

Liquid crystal elastomer shell actuators with negative order parameter.

Liquid crystals (LCs) are nonsolids with long-range orientational order, described by a scalar order parameter 〈 P 2 〉 = 1 2 〈 3 cos 2 ß - 1 〉 . Despite the vast set of existing LC materials, one-third of the order parameter value range, -1/2 < 〈P 2〉 < 0, has until now been inaccessible. Here, we present the first material with negative LC order parameter in its ground state, in the form of elastomeric shells. The optical and actuation characteristics are opposite to those of conventional LC elastomers (LCEs). This novel class of anti-ordered elastomers gives access to the previously secluded range of liquid crystallinity with 〈P 2〉 < 0, providing new challenges for soft matter physics and adding a complementary type of LCE actuator that is attractive for applications in, e.g., soft robotics.

Liquid-crystal order during synthesis affects main-chain liquid-crystal elastomer behavior.

This study presents the first direct comparison of the influence of liquid-crystal order during synthesis on the thermo-mechanical behaviors of main-chain liquid-crystal elastomers (LCEs) in thiol-acrylate networks. Six polydomain nematic elastomer (PNE) chemistries were compared directly by synthesizing with the mesogens in either an isotropic state (i-PNE) or a nematic state (n-PNE). The i-PNE networks were created in the presence of solvent, which disrupted any liquid-crystal order during network formation. Conversely, the n-PNE networks were created without the presence of solvent below the isotropic transition (TNI). Differential scanning calorimetry (DSC) was first performed, and it showed that i-PNE networks experienced a clearly defined nematic-to-isotropic transition upon heating, whereas the transition in n-PNE networks was unable to be identified, which may be the result of a nematic-to-paranematic phase transition. Dynamic mechanical analysis (DMA) tests revealed that while both networks maintained elevated loss tangent in the nematic region, only i-PNE networks prominently displayed dynamic soft elasticity behavior. The two-way shape switching behaviors of LCE networks were examined using actuation tests under a 100 kPa bias stress. It showed that the strain amplitude strongly depends on synthesis history; it ranges from 66% to 126% in i-PNE samples and 3% to 61% in n-PNE samples. To help interpret the different actuation strain behaviors between i-PNEs and n-PNEs, wide-angle X-ray scattering (WAXS) was then performed where the LCE samples were strained to 40%. The results showed that order parameter (S) in n-PNE samples (ranging from 0.37 to 0.50) is lower than that in i-PNE samples (0.54 for all cases), and the parameter decreased as the cross-linking density increased. The stress-strain behaviors of the LCE networks measured from uniaxial tension tests revealed that all i-PNE samples had a lower soft-elasticity plateau during loading compared to the n-PNE samples. Finally, free-standing strain recovery of LCE samples after being strained to 100% was investigated. Immediately after removing stress on the samples, i-PNE and n-PNE samples recovered 14% to 38% and 27% to 73% of strain, respectively. We discuss the advantages and disadvantages of the different synthetic histories on LCE design.

Cytotoxicity and thermomechanical behavior of biomedical shape-memory polymer networks post-sterilization.

Shape-memory polymers (SMPs) are being increasingly proposed for use in biomedical devices. This paper investigates the cytotoxicity, surface characteristics and thermomechanics of two acrylate-based SMP networks as a function of sterilization using a minimal essential media elution test, FTIR-ATR and dynamic mechanical analysis (DMA). Networks sterilized by low-temperature plasma elicited a cytotoxic response and are shown to completely destroy the cell monolayer. FTIR-ATR analysis showed evidence of surface oxidation with an increase and broadening of the absorbance peak from approximately 3500 to 3100 cm(-1), which is associated with an increase in hydroxyl groups. DMA revealed small, but statistically significant, differences in reduction of the glass transition temperatures of both networks when sterilized with gamma irradiation. One network showed an increase in rubbery modulus, which is an indication of crosslink density, after gamma irradiation. Lastly, practical sterilization concerns of SMP devices are discussed in light of the different methods.