Formation Processes of a Solid Electrolyte Interphase at a Silicon/Sulfide Electrolyte Interface in a Model All-Solid-State Li-Ion Battery.

Understanding the electrochemical reactions at the interface between a Si anode and a solid sulfide electrolyte is essential in improving the cycle stabilities of Si anodes in all-solid-state batteries (ASSBs). Highly dense Si films with very low roughnesses of <1 nm were fabricated at room temperature via cathodic arc plasma deposition, which led to the formation of a Si/sulfide electrolyte model interface. Li (de)alloying through the model interface hardly occurred during the first cycle, whereas it proceeded stably in subsequent cycles. Hard X-ray photoelectron spectroscopy and neutron reflectometry directly revealed that the reduction or oxidation of the interfacial component or Li3PS4 electrolyte occurred during the first cycle. Consequently, an interfacial layer with a thickness of 13 nm and primarily composed of Li2S, SiS2, and P2S5 glasses was formed during the first cycle. The interfacial layer acted as a Li-conductive, electron-insulating solid electrolyte interphase (SEI) that provided reversible (de)lithiation. Our model interface directly demonstrates the electrochemical reaction processes at the Si/Li3PS4 interface and provides insights into the structures and electrochemical properties of SEIs to activate the (de)lithiation of Si anodes using a sulfide electrolyte.

Neutron reflectometry under high shear in narrow gap for tribology study.

An operando analysis method has been established for evaluating the interfacial structure of an adsorbed layer formed by an additive on a metal surface under fluid lubricated conditions. A parallel-face narrow gap viscometer installed in an energy-resolved neutron reflectometer is used to evaluate the change in the interfacial structure under high shear. The viscometer was designed to operate at a high shear rate while maintaining a µm-order constant gap between two parallel surfaces. When an additive-free base oil was sandwiched in the gap, the neutron reflectivity profiles without and with upper surface rotation were the same. This demonstrates that the reflectivity profiles can be accurately measured regardless of whether the upper surface is rotated. When a base oil containing a polymethacrylate-based additive was sandwiched in the gap, both the thickness and density of the adsorbed additive layer in the rotation (shear field) condition were lower than those in the non-rotation (static) condition. This demonstrates that the proposed method can be used to analyse the structural changes in the adsorbed layer formed by an oil additive on a surface. This combination of a neutron reflectometer and narrow gap viscometer is a promising approach to near-future tribological studies.

Quasi-elastic neutron scattering reveals the relationship between the dynamical behavior of phospholipid headgroups and hydration water.

The dynamics of hydration water (HW) in 1,2-dimyristoyl-sn-glycero-3-phosphoethanolamine (DMPE) was investigated by means of quasi-elastic neutron scattering (QENS) and compared with those observed in 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC). The headgroup dynamics of DMPE was investigated using a mixture of tail-deuterated DMPE and D2O, and the QENS profiles were interpreted as consisting of three modes. The fast mode comprised the rotation of hydrogen atoms in -NH3+ and -CH2- groups in the headgroup of DMPE, the medium-speed mode comprised fluctuations in the entire DMPE molecule, and the slow mode comprised fluctuations in the membrane. These interpretations were confirmed using molecular dynamics (MD) simulations. The HW dynamics analysis was performed on a tail-deuterated DMPE and H2O mixture. The QENS profiles were analyzed in terms of three modes: (1) a slow mode, identified as loosely bound HW in the DMPC membrane; (2) a medium-speed mode similar to free HW in the DMPC membrane; and (3) a fast mode, identified as rotational motion. The relaxation time for the fast mode was approximately six times shorter than that of rotational water in DMPC, consistent with the results of terahertz time-domain spectroscopy. The activation energy of medium-speed HW in DMPE differed from that of free HW in DMPC, suggesting the presence of different hydration states or hydrogen-bonded networks around the phosphocholine and phosphoethanolamine headgroups.

Neutron reflectivity study on the nanostructure of PMMA chains near substrate interfaces based on contrast variation accompanied with small molecule sorption.

In the case of poly(methyl methacrylate) (PMMA) thin films on a Si substrate, thermal annealing induces the formation of a layer of PMMA chains tightly adsorbed near the substrate interface, and the strongly adsorbed PMMA remains on the substrate, even after washing with toluene (hereinafter called adsorbed sample). Neutron reflectometry revealed that the concerned structure consists of three layers: an inner layer (tightly bound on the substrate), a middle layer (bulk-like), and an outer layer (surface) in the adsorbed sample. When an adsorbed sample was exposed to toluene vapor, it became clear that, between the solid adsorption layer (which does not swell) and bulk-like swollen layer, there was a "buffer layer" that could sorb more toluene molecules than the bulk-like layer. This buffer layer was found not only in the adsorbed sample but also in the standard spin-cast PMMA thin films on the substrate. When the polymer chains were firmly adsorbed and immobilized on the Si substrate, the freedom of the possible structure right next to the tightly bound layer was reduced, which restricted the relaxation of the conformation of the polymer chain strongly. The "buffer layer" was manifested by the sorption of toluene with different scattering length density contrasts.

Interfacial Distribution of Nafion Ionomer Thin Films on Nitrogen-Modified Carbon Surfaces.

Chemically modified carbon supports for the cathode catalyst layers of polymer electrolyte fuel cells (PEFCs) show considerable promise for boosting the oxygen reduction reaction. This study evaluated the ionomer distribution of Nafion ionomer thin films on nitrogen (N)-modified carbon surfaces along their depth direction. Neutron reflectivity (NR) measurements performed using the double-contrast technique with H2O and D2O revealed that the introduction of N functional groups to carbon thin films promoted ionomer adsorption onto the surface under wet conditions (22 °C, 85% relative humidity). Molecular dynamics (MD) simulations conducted to verify the origin of the robust contact between the ionomer and N-modified carbon surface revealed an ionomer adsorption mechanism on the N-modified carbon surfaces, which involved Coulomb interactions between the positively charged carbon surface and the ionomer side chains with negatively charged sulfonic acid groups. The positive surface charge, which was determined using the contents of the N functional groups estimated by X-ray photoelectron spectroscopy, was found to be sufficient as an impetus for ionomer adsorption. This strategy involving NR measurements and MD simulations can provide insights into the solid-ionomer interfacial structures in a cathode catalyst layer and can therefore be extensively employed in studies on PEFCs.

Neutron Reflectivity Study on the Suppression of Interfacial Water Accumulation between a Polypropylene Thin Film and Si Substrate Using a Silane-Coupling Agent.

We measured the neutron reflectivity (NR) of isotactic polypropylene (PP) thin films deposited on Si substrates modified by hexamethyldisilazane (HMDS) at the saturated vapor pressure of deuterated water at 25 °C and 60 °C/85% RH to investigate the effect of HMDS on the interfacial water accumulation in PP-based polymer/inorganic filler nanocomposites and metal/resin bonding materials. We found that the amount of water accumulated at the PP/Si interface decreased with increasing immersion time of the Si substrate in a solution of HMDS in hexane prior to PP film deposition. During the immersion of the Si substrate, the HMDS molecules were deposited on the Si substrate as a monolayer without aggregation. Furthermore, the coverage of the HMDS monolayer on the Si substrate increased with increasing immersion time. At 60 ° C and 85% RH, only a slight amount of interfacial water was detected after HMDS treatment for 1200 min. As a result, the maximum concentration of interfacial water was reduced to 0.1 from 0.3, where the latter corresponds to the PP film deposited on the untreated substrate.

Neutron Reflectometry & Simultaneous Measurements of Rheology and Small Angle Neutron Scattering Studies for Polyether Modified Silicone Vesicle Systems.

Polyethyleneglycol 12 mol / polydimethylsiloxane co-polymer (PEG-12 dimethicone) is a type of polyether modified silicone (PEMS), which can form a lamellar liquid crystalline phase, and is widely used in cosmetics. The structural changes of PEG-12 dimethicone caused by water contents as well as shear flow were evaluated using simultaneous measurements of rheology and small angle neutron scattering (Rheo-SANS) and neutron reflectometry (NR). At high PEG-12 dimethicone concentrations (≥ 36 wt%), a reorientation of plate-like lamellar structures were observed and the neutral orientation was the most favorable. However, lamella-to-vesicle transitions were hardly observed. PEG-12 dimethicone turned out to form a bi-layer on a hydrophilized Si-wafer in a similar manner to that in bulk though the structure had a certain level of roughness.

Zwitterionic Poly(carboxybetaine) Brush/Albumin Conjugate Films: Structure and Lubricity.

Artificial cartilages build up a highly lubricious system with the harmony of biomacromolecules and water. Bioconjugate thin films composed of a zwitterionic poly(carboxybetaine methacrylate) (PCB) brush platform and bovine serum albumin (BSA) were designed. BSA conjugation to the PCB brush chains was achieved by carbodiimide chemistry to give PCB brush/BSA conjugate films. The PCB brush/BSA conjugate films exhibited adaptable interfacial properties due to the amphiphilic nature of BSA. Neutron reflectivity showed that BSAs were localized at the liquid side of the conjugate films in PBS and the BSA conjugation slightly reduced the water content of the top layer, while the swollen state of the carpet PCB brush layer remained unchanged. The PCB brush/BSA conjugate films showed improved lubricity in the boundary lubrication mode but slightly worse fluid lubrication induction properties. This conjugate film could be a model system for the investigation of zwitterion/protein composite interfaces and is worth developing biomaterials that require lubrication in vivo.

Enhanced Glass Transition Temperature of Thin Polystyrene Films Having an Underneath Cross-Linked Layer.

Due to the importance of the interface in the segmental dynamics of supported macromolecule ultrathin films, the glass transition temperature (Tg) of polystyrene (PS) ultrathin films upon solid substrates modified with a cross-linked PS (CLPS) layer has been investigated. The results showed that the Tg of the thin PS films on a silica surface with a ∼5 nm cross-linked layer increased with reducing film thickness. Meanwhile, the increase in Tg of the thin PS films became more pronounced with increasing the cross-linking density of the layer. For example, a 20 nm thick PS film supported on CLPS with 1.8 kDa of cross-linking degree exhibited a ∼35 and ∼50 K increase in Tg compared to its bulk and that on neat SiO2 substrate, respectively. Such a large Tg elevation for the ultrathin PS films was attributed to the interfacial aggregation states in which chains diffused through nanolevel voids formed in the cross-linked layer to the SiO2-Si surface. In such a situation, the chains were topologically constrained in the cross-linked layer with less mobility. These results offer us the opportunity to tailor interfacial effects by changing the degree of cross-linking, which has great potential application in many polymer nanocomposites.

Hydrophobicity of the Pentafluorosulfanyl Group in Side Chains of Polymethacrylates by Evaluation with Surface Free Energy and Neutron Reflectivity.

A hydrophobic surface or coating is required for surface protection, anti-fouling, adhesion, and other applications. For the achievements of hydrophobic properties, fluorine-based coatings, such as the introduction of trifluoromethyl or difluoromethylene groups, are conventionally employed. Recent developments in synthetic chemistry have indicated other organic fluoroalkyl groups that are suitable for achieving a more hydrophobic surface. In this study, we focused on the hydrophobic properties of the pentafluorosulfanyl (-SF5) group. We synthesized polymethacrylates with -SF5 groups or other functional groups (-CF3, -CH3, and -H) in their side chains and evaluated their hydrophobicity based on contact angles of water and ethylene glycol and the affinities of their films to water through neutron reflectivity measurements to demonstrate the superior hydrophobic properties of the -SF5 group. The water contact angle on the polymethacrylate film with -SF5 groups was larger, which suggested that the surface free energy was lower than that of the other polymethacrylate thin films with pendant side chains of -CF3, -CH3, and -H. In addition, the fitting analyses of the neutron reflectivity profiles of the thin polymer films in contact with air and water revealed the lowest affinity between water and the surface of polymethacrylate films with -SF5 groups among the films of the synthesized polymers. Thus, we demonstrated the potential of pentafluorosulfanyl groups as advanced hydrophobic groups.

Effects of Lithium Bis(oxalate)borate Electrolyte Additive on the Formation of a Solid Electrolyte Interphase on Amorphous Carbon Electrodes by Operando Time-Slicing Neutron Reflectometry.

Comprehensive analyses were performed using neutron reflectivity and hard X-ray photoelectron spectroscopy to understand the structure and composition of the solid electrolyte interphase (SEI) layer during charge-discharge processes and because of the addition of lithium bis(oxalate)borate (LiBOB) to improve the battery performance. The chemical composition of the SEI was assessed using these methods, and the amount of Li+ intercalated in the anode during the electrochemical reaction was evaluated. The results demonstrated that Li2C2O4 was produced initially but later decomposed to Li2CO3 on the first charge cycle. Presumably, the SEI layer formed by the decomposition of LiBOB was a single dense layer and chemically stable during the further charge-discharge processes owing to the difference in the reaction process. Therefore, the reduced Li+ transfer resistance and charging capacity accounted for the substantial improvement contributed by adding LiBOB. Moreover, the charges used for the intercalation of Li+ and SEI formation during the two-cycle processes were analyzed. The addition of LiBOB increased the discharge capacity of the anode and provided an additional charge used for SEI formation, presumably for decomposing Li2C2O4, which could reflect the durability of the Li-ion batteries. The electrode, electrolyte, and charge-discharge reactions affect the SEI properties and consequently the electrochemical reactions. Therefore, additional investigations under different charge-discharge conditions would reveal important characteristics such as the charge and discharge efficiency, output performance, and safety.

Effect of Oligomer Segregation on the Aggregation State and Strength at the Polystyrene/Substrate Interface.

The interfacial strength of polystyrene (PS) with and without PS oligomers in contact with a glass substrate was examined to determine the relationship between the interfacial aggregation state and adhesion. The shear bond strength and adsorbed layer thickness of neat PS exhibited a similar dependence on the thermal annealing time: they increased to constant values within almost the same time. This implies that the adhesion of the polymer is closely related to the formation of an adsorbed layer at the adhesion interface. Nevertheless, in the case of PS with a small amount of oligomer, the shear bond strength decreased, while the adsorbed layer thickness was almost the same as that of neat PS. Based on the results of interfacial analyses, we propose that the interfacial segregation of the oligomer reduced the entanglement between the interfacial free chains in the adsorbed layer and the bulk chains.

Interfacial Selective Study on the Gelation Behavior of Aqueous Methylcellulose Solution via a Quartz Crystal Microbalance.

It is important to understand the interfacial structure and physical properties of a polymer material to improve its function. In this study, we used a quartz crystal microbalance (QCM) and neutron reflectivity (NR) measurements to evaluate the viscoelasticity and structure of an aqueous methylcellulose solution near the gold interface. The apparent shear modulus, which was calculated from the complex frequency, was used to assess gelation behavior. The apparent shear modulus determined via the QCM suggested high-frequency rheological properties that reflected the relaxation of skeletal stretching and rotational motion of polymer segments, as well as cooperative motion of the various functional groups. The gelation temperature was found to be lowered at the interface in comparison with that of the bulk. It is suggested that the QCM can evaluate the shear modulus accompanying the gelation near the interface. The interfacial segregation on the gold substrate caused by the surface free energy and long-range van der Waals interaction was observed from NR measurements.

The role of the molecular weight of the adsorbed layer on a substrate in the suppressed dynamics of supported thin polystyrene films.

The adsorbed layer on a solid surface plays a crucial role in the dynamics of nanoconfinement polymer materials. However, the influence of the adsorbed layer is complex, and clarifying this influence on the dynamics of confined polymers remains a major challenge. In this paper, SiO2-Si substrates with various thicknesses and adsorbed layers of PS with various molecular weights were used to reveal the effect of the adsorbed layer on the corresponding segmental dynamics of the supported thin PS films. Strongly suppressed segmental dynamics of thin PS films were observed for the films supported on thicker adsorbed layers or prepared using higher molecular weight. Neutron reflectivity revealed that the overlap region thickness between the adsorbed layer and the top overlayer increased with increasing thickness and molecular weight of the adsorbed layer, both of which correlate well with the distance over which the polystyrene dynamics were depressed by the adsorbed layer. The results show that the influencing distance of the adsorbed layer is related to the overlap zone formed between the adsorption layer and the upper thin film. The effect of the adsorbed layer molecular weight can be ascribed to the fact that large loops and long tails in the adsorbed layer result in stronger interpenetrations and entanglements between polymer chains in the adsorbed layer and in the overlayer, causing a stronger substrate effect and suppression of the segment dynamics of the supported thin PS films.

Neutron flat-panel detector using In-Ga-Zn-O thin-film transistor.

Neutron imaging is a powerful tool for observing the internal structure of an object without destroying the object. Neutron imaging (neutron radiography) is a prominent application of neutrons but still requires significant improvements, for example, in sensitivity, resolution, radiation hardness, and handling of neutron imaging detectors. This paper presents the development and the first neutron imaging results of a neutron flat-panel detector (nFPD) based on an In-Ga-Zn-O (IGZO) thin-film transistor (TFT)/photodiode array coupled with a LiF/ZnS scintillator sheet. Direct photo-coupling to the scintillator increases the light collection efficiency. Moreover, unlike lens-coupled neutron cameras, the proposed detector is compact and easy to handle. Owing to the high off-state resistance of IGZO TFTs, their leakage current is lower than that of conventional TFTs, enabling the IGZO TFTs to hold an accumulated charge for a longer period of time and allowing longer exposure times for imaging. This would be a powerful feature for imaging at compact neutron sources with limited flux. This paper reports on the first neutron imaging results with an IGZO nFPD, its performance evaluation, and a demonstration of three-dimensional computed tomography with neutrons.

Neutron reflectometry-based in situ structural analysis of an aligning agent additive for the alignment of nematic liquid crystals on solid substrates.

Surface aligning agents, such as amphiphilic surfactants, are widely used to control the initial alignment of nematic liquid crystals (NLCs) in liquid crystal displays (LCDs). Generally, these agents are first coated on a substrate prior to NLC introduction. When mixed with NLCs, long alkyl chain amphiphilic agent additives may control the NLC alignment without requiring pretreatment because they may spontaneously form an adsorbed layer at the solid-NLC interface. These self-assembled layers (SALs) appear promising in the effective control of the initial alignment of LCDs. However, direct observation of the adsorbed layer structure in contact with the NLCs is challenging due to probe limitations. Furthermore, the areal densities and alignments of the amphiphiles adsorbed from NLCs at the solid-NLC interface are not previously reported. Herein, the structure of the surface aligning agent n-hexadecyltrimethylammonium-d42 bromide (d-CTAB) was investigated at the silicon-NLC interface using in situ neutron reflectometry (NR), which indicated that the CTAB self-assembled as a monolayer, with its alignment dependent on the amphiphile concentration. At low amphiphile concentrations, the alignment of the SAL and NLCs was parallel to the substrate. With increasing amphiphile concentration, the number of amphiphiles attached to the substrate increased within the framework of the Gibbs monolayer, with the alignment of the amphiphiles and NLCs becoming perpendicular to the substrate. The experimental setup used here is comparable to those of more natural systems, such as those found in the alignment of NLCs in LCDs.

Cononsolvency of Poly[2-(methacryloyloxy)ethyl phosphorylcholine] in Ethanol-Water Mixtures: A Neutron Reflectivity Study.

Molecular mechanisms underlying the cononsolvency, a re-entrant coil-to-globule-to-coil conformational transition of polymer chains in mixtures of two good solvents, of poly[2-(methacryloyloxy)ethyl phosphorylcholine] (PMPC) in ethanol-water binary mixtures were complementarily investigated. This was accomplished by following a statistical mechanical model for competitive hydrogen bonding combined with the cooperative solvation concept as well as neutron reflectivity (NR) experiments employing contrast variation in the cononsolvents. The experimental re-entrant aggregation of the PMPC chains in ethanol-water mixed solvents, obtained on the basis of turbidity was accurately reproduced by theoretical calculations. The calculation proved the relatively strong cooperativity of ethanol and the preferential interaction of water, while the total coverage of solvents was the lowest at an ethanol volume fraction (fethanol) of 0.90. At this level, the cononsolvency was the most significant, and the collapsed PMPC chains were solvated with more water than the bulk mixed solvent. The ethanol-water cononsolvency for the PMPC brushes on a planar silicon wafer was investigated by NR experiments, and the solvent composition involved in the collapsed PMPC brush was addressed according to the contrast variation study with mixed solvents of water, deuterium oxide, ethanol-d5, and ethanol-d6. The collapsed PMPC brushes at fethanol = 0.90 contained more water than the bulk solvent. The preferential distribution of water in the collapsed PMPC brush was consistent with the simulation results. Therefore, the molecular mechanism for the cononsolvency of PMPC in ethanol-water mixed solvents based on competitive hydrogen bonding coupled with cooperative solvation was experimentally rationalized.

Modification of a Polymer Surface by Partial Swelling Using Nonsolvents.

Surface modification without changing the physical properties in the bulk is of pivotal importance for the development of polymers as devices. We recently proposed a simple surface functionalization method for polymer films by partial swelling using a nonsolvent and demonstrated the incorporation of poly(2-methoxyethyl acrylate) (PMEA), which has an excellent antibiofouling ability, only into the outermost region of a poly(methyl methacrylate) (PMMA) film. We here extend this technology to another versatile polymer, polystyrene (PS). In this case, PS and PMEA have different solubility parameters making it difficult to select a suitable solvent, which is a nonsolvent for PS and a good solvent for PMEA, unlike the combination of PMMA with PMEA. Thus, such a solvent was first sought by examining the swelling behavior of PS films in contact with various alcohols. Once a mixed solvent of methanol/1-butanol (50/50 (v/v)) was chosen, PMEA chains could be successfully incorporated at the outermost region of the PS film. Atomic force microscopy in conjunction with neutron reflectivity revealed that chains of PMEA incorporated in the PS surface region were well swollen in water. This leads to an excellent ability to suppress the adhesion of platelets on the PS film.

Investigation of Interfacial Water Accumulation between Polypropylene Thin Film and Si Substrate by Neutron Reflectivity.

We performed neutron reflectivity (NR) measurements of isotactic polypropylene (PP) thin films deposited on a Si substrate at the saturated vapor pressure of deuterated water to investigate interfacial water accumulation between the PP and metal surfaces in PP-based polymer/inorganic filler nanocomposites and metal/resin bonding materials. The PP thin films prepared on a Si substrate by a spin-coating technique were adequate as a model system for the PP/metal interface in these materials. A water-rich layer with a maximum water concentration of 0.5, which was considerably higher than those reported in previous studies of organic/inorganic interfaces, was observed within a width of approximately 3 nm at the interface under saturated vapor conditions. This could be attributed to the weak interaction between the PP thin film and the Si substrate. The pathway of moisture transport to the interfacial region was along the interface rather than through the PP film because the hydrophobic PP thin film does not entirely swell with water vapor.

Polymer Brush Formation Assisted by the Hierarchical Self-Assembly of Topological Supramolecules.

The development of methods for the polymer brush layer formation on material surfaces to improve the surface properties has been researched for decades. Here, we report a novel approach for the formation of a polymer brush layer on materials and the alteration of the surface properties using a pseudo-polyrotaxane nanosheet (PPRNS). In the PPRNS, ß-cyclodextrin (CD) selectively covered the central poly(propylene oxide)29 segment of the carboxyl-terminated poly(ethylene oxide)75-b-poly(propylene oxide)29-b-poly(ethylene oxide)75 (COOH-EO75PO29EO75) triblock copolymer to form columnar crystals. The EO chains of COOH-EO75PO29EO75 then adopt polymer brush conformations and exhibit an oil-repellent property on the material surfaces. Based on the flexibility derived from the nanosheet structure, the PPRNS showed high adhesion to the Blu-ray disk substrate (1D bending), polystyrene spherical beads (2D bending), and random rough surface of pork skin. The PPRNS is expected to become a new method for obtaining polymer brush layers and improving the surface properties irrespective of the material type.