Biodegradable Polymer Matrix Composites Containing Graphene-Related Materials for Antibacterial Applications: A Critical Review.

For the first time, the present review critically evaluates biodegradable polymer matrix composites containing graphene-related materials (GRMs) for antibacterial applications while discussing their development, processing routes, mechanical properties, and antibacterial activity. Due to its suitable biological properties and processability, chitosan has been the most widely used biodegradable polymer for the fabrication of GRM-containing composites with antibacterial properties. The majority of biodegradable polymers (including cellulose-, gelatine-, PVA-, PCL-, and PHA-based polymers) exhibit little to no antibacterial effect alone; however, they show significant antibacterial activity (>70%) when combined with GRMs. In vitro and in vivo studies indicate that GRMs functionalization with biodegradable polymers also reduces potential GRM cytotoxicity. Overall, GRMs in biodegradable polymer matrices provide attractive antibacterial activity against a broad spectrum of bacteria (>30 different bacteria) along with improved mechanical properties over pristine polymers, where the type and the degree of improvement provided by GRMs depend on the specific matrix. For example, the addition of GRMs into chitosan, PVA, and PCL matrices increases their tensile strength by 80%, 180%, and 40%, respectively. Challenges remain in understanding the effects of processing routes and post-processing methods on the antibacterial activity and biocompatibility of biodegradable polymer/GRM composites. Given their promising properties and functionality, research on these composites is expected to further increase along with the implementation of new composite systems. These would include a wide range of applications, e.g., wound dressings, tissue engineering, drug delivery, biosensing, and photo-thermal therapy, as well as non-medical use, e.g., antibacterial food packaging, water treatment, and antibacterial fabrics. STATEMENT OF SIGNIFICANCE: Graphene-related materials (GRMs) in polymer matrices can provide excellent antibacterial activity against a broad spectrum of bacteria together with improved mechanical properties (e.g., tensile strength and elastic modulus) over pristine polymers; thus, research efforts and applications of biodegradable polymer matrix composites containing GRMs have increased notably in the last ten years. For the first time, the present review critically evaluates biodegradable polymer matrix composites containing GRMs for antibacterial applications while discussing their development, processing routes, mechanical properties, and antibacterial activity. Future research directions for each composite system are proposed to shed light on overcoming the existing challenges in composite performance (e.g., mechanical properties, toxicity) reported in the literature.

Surface, Subsurface and Tribological Properties of Ti6Al4V Alloy Shot Peened under Different Parameters.

Ti6Al4V alloy was shot peened by using stainless-steel shots with different sizes (0.09-0.14 mm (S10) and 0.7-1.0 mm (S60)) for two durations (5 and 15 min) using a custom-designed peening system. The shot size was the main parameter modifying the roughness (0.74 µm for S10 vs. 2.27 µm for S60), whereas a higher peening time slightly increased roughness. Hardness improved up to approximately 35% by peening with large shots, while peening time was insignificant in hardness improvement. However, longer peening duration with large shots led to an unwanted formation of micro-cracks and delamination on the peened surfaces. After dry sliding wear tests, the mass loss of peened samples (S60 for 15 min) was 25% higher than that of un-peened samples, while the coefficient of friction decreased by 12%. Plastically deformed regions and micro-scratches were observed on the worn surfaces, which corresponds to mostly adhesive and abrasive wear mechanisms. The present study sheds light on how surface, subsurface and tribological properties of Ti6Al4V vary with shot peening and peening parameters, which paves the way for the understanding of the mechanical, surface, and tribological behavior of shot peened Ti6Al4V used in both aerospace and biomedical applications.

Fracture strengths of endocrown restorations fabricated with different preparation depths and CAD/CAM materials.

The objectives of this study were to compare the fracture strength of endocrown restorations fabricated with different preparation depth and various CAD/CAM ceramics, and to assess the fracture types. Endodontically treated 100 extracted human permanent maxillary centrals were divided into two preparation depth groups as short (S: 3-mm-deep) and long (L: 6-mm-deep), then five ceramic subgroups, namely: feldspathic-ceramic (Vita Mark II-VM2), lithium-disilicate glass-ceramic (IPS e.max CAD-E.max), resin-ceramic (LAVA Ultimate-LU), polymer infiltrated ceramic (Vita Enamic-VE) and monoblock zirconia (inCoris TZI-TZI) (n=10/subgroup). The endocrowns were fabricated by CAD/CAM and were cemented with resin cement (RelyX U200). The teeth were thermally cycled (5,000cycles) and fracture tests were performed at 45º angle to the teeth. The data were statistically analyzed (Kruskal-Wallis, Mann Whitney U), failure modes were evaluated with stereomicroscopy. Zirconia group provided the statistically highest fracture strength, but also exhibited non-repairable failures. Preparation depth has an effect on the fracture strength only for feldspathic ceramic.