Biodegradable Alkali-Swellable Emulsion Polymers: Industrial and Commercial Thickeners.

Sustainability and circularity are key issues facing the global polymer industry. The search for biodegradable and environmentally-friendly polymers that can replace conventional materials is a difficult challenge that has been met with limited success. Alternatives must be cost-effective, scalable, and provide equivalent performance. We report that latexes made by the conventional emulsion polymerization of vinyl acetate and functional vinyl ester monomers are efficient thickeners for consumer products and biodegrade in wastewater. This approach uses readily-available starting materials and polymerization is carried out in water at room temperature, in one pot, and generates negligible waste. Moreover, the knowledge that poly(vinyl ester)s are biodegradable will lead to the design of new green polymer materials.

Synthesis and Biodegradation Studies of Low-Dispersity Poly(acrylic acid).

Poly(acrylic acid) (PAA) is produced on an industrial scale and widely-used in applications such as personal care products and cleaning formulations that end up "down-the-drain." Relatively high molecular weight PAA is considered poorly biodegradable, but little is known about the biodegradability of low molecular weight PAA at the wastewater treatment plant according to current regulatory and industrial Organization for Economic Co-operation and Development (OECD) standards. The synthesis, separation, and characterization of a series of ultralow dispersity PAA oligomers (i.e., D < 1.10) in the molecular weight range Mn ≈ 350-1200 Da and the results of biodegradability testing are reported. Miniaturized, high-throughput screening studies in a parallel respirometer reveals a strong trend toward lower biodegradation at higher molecular weight; these results are confirmed and expanded using standardized method OECD 301F. Biodegradability reaches ≈40% at Mn = 380 Da, ≈26% at Mn = 770 Da, and ≈17% at Mn = 1190 Da for discrete polyacid oligomers. These data not only shed light on potential biodegradation mechanisms for linear PAA, but also may inspire the future design of biodegradable PAA-containing macromolecules.

Correction to "Multicompartment Micelles by Aqueous Self-Assembly of µ-A(BC) n Miktobrush Terpolymers".

[This corrects the article DOI: 10.1021/acsomega.6b00284.].

Multicompartment Micelles by Aqueous Self-Assembly of µ-A(BC) n Miktobrush Terpolymers.

The aqueous self-assembly of µ-A(BC) n miktobrush terpolymers has been studied using dynamic light scattering and cryogenic transmission electron microscopy. In this system, the A block is hydrophilic poly(ethylene oxide), "O", the B block is hydrophobic poly(methylcaprolactone), "C", and the C block is hydrophobic and oleophobic poly(perfluoropropylene oxide), "F". Two terpolymers were examined: one with an average of about two C blocks and two F blocks and another with an average of about three C blocks and two F blocks. In both cases, the total molar mass is near 40 kg mol-1, and the volume fraction of the single O block is greater than 50% of the whole. Both samples form multicompartment micelle structures with subdivided solvophobic cores of C and F domains. The morphologies observed are generally analogous to those previously observed for the self-assembly of µ-ABC miktoarm star terpolymers, namely, "raspberry" and "hamburger" micelles; however, an intriguing multicompartment polymersome morphology with compartmentalized solvophobic bilayers is also observed. These results are interpreted in terms of the relative strengths of the competing interactions among the three blocks and the solvent and in terms of the constraints imposed by the miktobrush architecture.

Preparation and performance of hydroxypropyl methylcellulose esters of substituted succinates for in vitro supersaturation of a crystalline hydrophobic drug.

We prepared hydroxypropyl methylcellulose (HPMC) esters of substituted succinates and examined their performance for improving the aqueous solubility of crystalline hydrophobic drugs in spray-dried dispersions (SDDs). From one HPMC, we synthesized five HPMC esters using various monosubstituted succinic anhydrides. These HPMC esters along with a commercial HPMC acetate succinate (HPMCAS) were spray-dried from solutions with phenytoin. The SDDs with different matrices at 10 wt % loading had very similar bulk properties with a minimal amount of detectable crystalline phenytoin as revealed by scanning electron microscopy (SEM), powder X-ray diffraction (powder XRD), and differential scanning calorimetry (DSC). In solution, while the SDD with HPMCAS was very effective at achieving high levels of phenytoin supersaturation initially, it was not competent at maintaining such supersaturation due to the rapid crystallization of the dissolved phenytoin. Alternatively, SDDs with several synthesized HPMC esters of substituted succinates not only achieved rather high initial supersaturation but also maintained high concentrations for extended time (i.e., 1.5 h and longer). Such maintenance was largely ascribed to the inhibition of phenytoin nucleation. Structure-property relationships were established, and the most successful systems contained a high degree of substitution and a combination of a thioether with neighboring weak electron-withdrawing groups in the substituted succinic anhydrides. The effective maintenance of supersaturated solutions was only found in SDDs with rather low drug loadings, which indicates the significance of sufficiently high concentrations of polymer additives in the dissolution media.