Corrigendum: Enhanced electrochemical properties of catalyst by phosphorous addition for direct urea fuel cell.

[This corrects the article DOI: 10.3389/fchem.2020.00777.].

Hierarchical PtCuMnP Nanoalloy for Efficient Hydrogen Evolution and Methanol Oxidation.

The higher amount of Pt usage and its poisoning in methanol oxidation reaction in acidic media is a major setback for methanol fuel cells. Herein, a promising dual application high-performance electrocatalyst has been developed for hydrogen evolution and methanol oxidation. A low Pt-content nanoalloy co-doped with Cu, Mn, and P is synthesized using a modified solvothermal process. Initially, ultrasmall ≈2.9 nm PtCuMnP nanoalloy is prepared on N-doped graphene-oxide support and subsequently, it is characterized using several analytical techniques and examined through electrochemical tests. Electrochemical results show that PtCuMnP/N-rGO has a low overpotential of 6.5 mV at 10 mA cm-2 in 0.3 m H2 SO4 and high mass activity for the hydrogen evolution reaction. For the methanol oxidation reaction, the PtCuMnP/N-rGO electrocatalyst exhibits robust performance. The mass activity of PtCuMnP/N-rGO is 6.790 mA mg-1 Pt , which is 7.43 times higher than that of commercial Pt/C (20% Pt). Moreover, in the chronoamperometry test, PtCuMnP/N-rGO shows exceptionally good stability and retains 72% of the initial current density even after 20,000 cycles. Furthermore, the PtCuMnP/N-rGO electrocatalyst exhibits outstanding performance for hydrogen evolution and methanol oxidation along with excellent anti-poisoning ability. Hence, the developed bifunctional electrocatalyst can be used efficiently for hydrogen evolution and methanol oxidation.

Enhanced Thermal Stability and Conductivity of FeF3 Using Ni-Coated Carbon Composites: Application as High-Temperature Cathodes in Thermal Batteries.

Cathode active materials and conductive additives for thermal batteries operating at high temperatures have attracted research interest, with a particular focus on compounds offering high thermal stability. Recently, FeF3 has been proposed as a candidate for high-voltage cathode materials; however, its commercialization is hindered by its low conductivity. In this study, conductive additives, such as Ni-coated carbon composites (multi-walled carbon nanotubes (MWCNTs) and carbon black (CB)), were utilized to enhance the thermal stability and conductivity of FeF3. The incorporation of metal-carbon conductive additives in the FeF3 composite increased the thermal stability by more than 10 wt.% and ensured high capacity upon conductivity enhancement. The FeF3@Ni/MWCB 15 wt.% composite containing 30 wt.% Ni exhibited a discharge capacity of ∼86% of the theoretical capacity of 712 mAh/g. The use of Ni-coated carbon-based conductive additives will allow the application of FeF3 as an effective high-temperature cathode material for thermal batteries.

FeF3/(Acetylene Black and Multi-Walled Carbon Nanotube) Composite for Cathode Active Material of Thermal Battery through Formation of Conductive Network Channels.

Considerable research is being conducted on the use of FeF3 as a cathode replacement for FeS2 in thermal batteries. However, FeF3 alone is inefficient as a cathode active material because of its low electrical conductivity due to its wide bandgap (5.96 eV). Herein, acetylene black and multi-walled carbon nanotubes (MWCNTs) were combined with FeF3, and the ratio was optimized. When acetylene black and MWCNTs were added separately to FeF3, the electrical conductivity increased, but the mechanical strength decreased. When acetylene black and MWCNTs were both added to FeF3, the FeF3/M1AB4 sample (with 1 wt.% MWCNTs and 4% AB) afforded a discharge capacity of approximately 74% of the theoretical capacity (712 mAh/g) of FeF3. Considering the electrical conductivity and mechanical strength, this composition was confirmed to be the most suitable.

Development of A 14.8-MEV Mono-Energetic Neutron Field in Korea Research Institute of Standards and Science.

A standard irradiation field for 14.8-MeV neutrons is under development for mono-energetic neutron standards research in the Korea Research Institute of Standards and Science, Republic of Korea. We developed a target chamber with the associated alpha particle (AAP) system for 14.8-MeV mono-energetic neutrons by a T(d,n)4He reaction. We designed the target chamber and the AAP detector system using a two-body kinematic calculation. We conducted simulations of the T(d,n)4He reaction on a tritiated target to determine a specification of the target and the AAP detector. This paper will discuss the simulation and calculation results for the associated particle system design.

Frontal peripheral osteomas: a retrospective study.

BACKGROUND: Osteomas are benign, slow-growing bone tumors that can be classified as central, peripheral, or extraskeletal. Central osteomas arise from the endosteum, peripheral osteomas from the periosteum, and extraskeletal osteomas within the muscle. Frontal peripheral osteomas are mainly encountered in plastic surgery. In this study, we retrospectively analyzed the clinical data of patients with frontal peripheral osteomas. METHODS: We retrospectively reviewed the medical records of patients who visited our hospital with frontal peripheral osteomas between January 2014 and June 2022. We analyzed the following variables: age, sex, tumor type (sessile or pedunculated), single or multiple, size, history of head trauma, operation, and recurrence. RESULTS: A total of 39 patients and 41 osteomas were analyzed, of which 29 osteomas (71%) were sessile and 12 osteomas (29%) were pedunculated. The size of the osteomas ranged from 4 to 30 mm, with an average size of 10 mm. The age of patients ranged from 4 to 78 years with a mean age of 52 years. There were seven men (18%) and 32 women (82%), and the man-to-woman ratio was 1:4.6. Two patients (5%) had multiple masses, with two osteomas in each, while only two patients (5%) had a history of head trauma. Twenty-nine patients (74%) underwent ostectomy by a direct approach, and none of the patients experienced recurrence. CONCLUSION: The epidemiologic data of our study will help plastic surgeons encounter frontal peripheral osteomas in the field to provide proper management for their patients.

Electrospun Poly(Styrene-Co-Vinylbenzyl Chloride-Co-Acrylonitrile) Nanofiber Mat as an Anion Exchange Membrane for Fuel Cell Applications.

A nanofiber mat of styrene-co-vinylbenzyl chloride-co-acrylonitrile copolymer as an anion exchange membrane (AEM) was synthesized via the electrospinning of organic reaction mixtures. The synthesized membranes were characterized using FT-IR spectroscopy for structural analysis. The AEM demonstrated a high ionic conductivity mainly due to the phase segregation in the membrane structure, as analyzed by transmission electron microscopy (TEM). The membrane properties such as water uptake, swelling ratio, and ion exchange capacity, as well as ionic conductivity, varied with the chemical composition. With the molar ratio of styrene, vinylbenzyl chloride, and acrylonitrile at 3:5:2, the highest ionic conductivity of 0.214 S cm-1 at 80 °C was observed. Additionally, the AEM retained 94% of original conductivity after 72 h of soaking in 1 M KOH solution.

Shear behavior of single cast-in anchor simulating characteristics of bridge bearing anchor.

A bridge bearing anchor transmits various loads of a superstructure to a substructure. Most anchors are generally designed without consideration of characteristics such as concrete pedestal, grout bedding, and anchor socket. This study investigated the shear behavior of anchors in accordance with the edge distance, embedment depth, compressive strength of concrete, and height of the concrete pedestal in order to simulate the practical characteristics of the bridge bearing anchors. The actual shear capacity of the anchor differs from the shear strengths calculated by the ACI 318 and EN 1992-4; especially, the importance of the embedment depth is underestimated in these codes. An increase in the height of the concrete pedestal has a negative effect on the shear capacity because of the stress concentration. The grout is fractured prior to the occurrence of local damages in concrete, resulting in a secondary moment. As a result, the effect of the level arm is observed. An equation, which can predict the relative cracking degree of concrete, is proposed by analyzing the displacement of grout and concrete. High strain occurs in the stirrups close to the anchor, and the behavior of the strain is more influenced by the embedment depth than the edge distance. The comparison of obtained and analytically evaluated failure loads by calculations according to EN 1992-4, Schmid model and Sharma model was conducted to consider the effect of supplementary reinforcement. Finally, the design equation of concrete breakout strength is modified to predict the more precise shear resistance of a bridge bearing anchor.

Anion Exchange Membranes for Fuel Cell Application: A Review.

The fuel cell industry is the most promising industry in terms of the advancement of clean and safe technologies for sustainable energy generation. The polymer electrolyte membrane fuel cell is divided into two parts: anion exchange membrane fuel cells (AEMFCs) and proton exchange membrane fuel cells (PEMFCs). In the case of PEMFCs, high-power density was secured and research and development for commercialization have made significant progress. However, there are technical limitations and high-cost issues for the use of precious metal catalysts including Pt, the durability of catalysts, bipolar plates, and membranes, and the use of hydrogen to ensure system stability. On the contrary, AEMFCs have been used as low-platinum or non-platinum catalysts and have a low activation energy of oxygen reduction reaction, so many studies have been conducted to find alternatives to overcome the problems of PEMFCs in the last decade. At the core of ensuring the power density of AEMFCs is the anion exchange membrane (AEM) which is less durable and less conductive than the cation exchange membrane. AEMFCs are a promising technology that can solve the high-cost problem of PEMFCs that have reached technological saturation and overcome technical limitations. This review focuses on the various aspects of AEMs for AEMFCs application.

Shielding Effectiveness and Impact Resistance of Concrete Walls Strengthened by High-Strength High-Ductility Concrete.

Following the fourth Industrial Revolution, electronic and data-based technology is becoming increasingly developed. However, current research on enhancing electromagnetic interference (EMI) shielding and the physical protection performance of structures incorporating these technologies is insufficient. Therefore, in this study aiming for the improvement of EMI shielding and structural performance of structures, twelve concrete walls were fabricated and tested to determine their shielding effectiveness and drop-weight impact resistance. Concrete walls strengthened by three thickness types of high-strength, high-ductility concrete (HSDC) have been considered. The test results showed that the shielding effectiveness with strengthening thickness increased by approximately 35.6-46.2%. Specimens strengthened by more than 40% and 10% of the strengthening area ratio of single- and double-layer, respectively, exhibited more than 20 dB of shielding effectiveness. Moreover, the relationship between the damaged area ratio and shielding effectiveness was evaluated by means of the drop-weight impact test. The structural performance and EMI shielding effectiveness improved as the HSDC thickness increased.

Ni-Fe phosphide deposited carbon felt as free-standing bifunctional catalyst electrode for urea electrolysis.

A free-standing catalyst electrode for the urea oxidation reaction (UOR) and hydrogen evolution reaction (HER) in a urea electrolysis cell was synthesized by electroplating a Ni-Fe alloy onto carbon felt, followed by phosphidation (P-NiFe@CF). The prepared P-NiFe@CF catalyst consisted of Ni5P4, NiP2, and FeP with 3D flower-like P-NiFe architecture on CF. P-NiFe@CF exhibited excellent electrocatalytic activity for the UOR (demanding only 1.39 V (vs. RHE) to achieve 200 mA cm-2), and for the HER with a low overpotential of 0.023 V (vs. RHE) at 10 mA cm-2, indicating its feasibility as a bifunctional catalyst electrode for urea electrolysis. A urea electrolysis cell with P-NiFe@CF as both the free-standing anode and cathode generated a current density of 10 mA cm-2 at a cell potential of 1.37 V (vs. RHE), which is considerably lower than that of water electrolysis, and also lower than previously reported values. The results indicate that the P-NiFe@CF catalyst electrodes can be used as free-standing bifunctional electrodes for urea electrolyzers.

Mechanical and Electrical Characteristics of Lightweight Aggregate Concrete Reinforced with Steel Fibers.

There is increased interest in applying electromagnetic (EM) shielding to prevent EM interference, which destroys electronic circuits. The EM shielding's performance is closely related to the electrical conductivity and can be improved by incorporating conductive materials. The weight of a structure can be reduced by incorporating lightweight aggregates and replacing the steel rebars with CFRP rebars. In this study, the effects of lightweight coarse aggregate and CFRP rebars on the mechanical and electrical characteristics of concrete were investigated, considering the steel fibers' incorporation. The lightweight coarse aggregates decreased the density and strength of concrete and increased the electrical conductivity of the concrete, owing to its metallic contents. The steel fibers further increased the electrical conductivity of the lightweight aggregate concrete. These components improved the EM shielding performance, and the steel fibers showed the best performance by increasing shielding effectiveness by at least 23 dB. The CFRP rebars behaved similarly to steel rebars because of their carbon fiber content. When no steel fiber was mixed, the shielding effectiveness increased by approximately 2.8 times with reduced spacing of CFRP rebars. This study demonstrates that lightweight aggregate concrete reinforced with steel fibers exhibits superior mechanical and electrical characteristics for concrete and construction industries.

Building-Information-Modeling Based Approach to Simulate Strategic Location of Shelter in Place and Its Strengthening Method.

It is important to consider establishing a shelter in place (SIP) using existing facilities to prepare for unpredictable and no-notice disasters. In this study, we evaluate the building-information-modeling (BIM)-based approach to simulate the strategic location of SIP and its strengthening method. BIM software was used to model a light rail station and analyze the elements of the facility that can affect the evacuation time to reach the SIP. The purpose of this study was to understand the effects of structural standards on the design of SIPs using a direct simulation. The differences between domestic and overseas standards were analyzed. An analysis was carried out to evaluate whether national specifications are satisfactory. As the proposed evacuation method is based on a rational human behavior analysis through a direct simulation, it was going to be a safer and faster route of evacuation in the case of physical terror attack situations for existing infrastructure, Furthermore, the SIP design is considered where reinforcement of the SIP structure is necessary. Three types of reinforcing were considered. Here, the use of high-strength, high-ductility concrete proved to be an effective method to improve the impact resistance of reinforced concrete walls and recommended for strengthening reinforced concrete members.

Effects of COVID-2019 on plastic surgery emergencies in Korea.

BACKGROUND: To fight the coronavirus disease 2019 (COVID-19) pandemic, many countries have implemented social distancing and lockdowns. We investigated the changes in the trauma patterns of emergency plastic surgeries in the midst of a pandemic. METHODS: A retrospective review of the medical records of all patients treated for emergency plastic surgeries was performed at our hospital in Seoul. We conducted the analysis between March 1 and June 30, 2020, and compared the data obtained with that of the same period in 2019. We also investigated changes in trauma patterns according to the social distancing level from July 2020 to February 2021. RESULTS: There was a total of 800 emergency plastic surgery patients from March to June 2020, which was less than the 981 in the corresponding period in 2019. The proportion of patients aged 7-17 years and ≥ 80 in 2020 showed a significant decrease. In 2020, patients presenting with facial trauma decreased and hand trauma, markedly laceration, increased significantly. In 2020, more injuries happened at home, whereas significantly fewer injuries happened on the streets. In 2020, slipping and sports injury decreased, whereas penetrating injury increased significantly. In the changes observed according to the social distancing level, there were significant differences in age classification, facial open wound, and the mechanism of injury. CONCLUSION: Social distancing has caused a change in emergency plastic surgeries. To ensure safe and appropriate treatment, strict epidemiologic workup and protective equipment are required.

Evaluation on the Microstructure and Durability of High-Strength Concrete Containing Electric Arc Furnace Oxidizing Slag.

The application of electric arc furnace oxidizing slag (EAS) in high strength concrete (HSC) as the cementitious material is investigated in this study. The microstructure and mechanical properties of HSC with four different replacement ratios of EAS were evaluated and HSC with two replacement ratios of ground granulated blast furnace slag (GBS) was used for performance comparison. The results show that the HSC with EAS replacement ratios smaller than 15% undergo similar hydration processes and result in a similar final product when compared with those of NC-NN. Increases in EAS replacement ratio cause a reduction in Ca(OH)2 content; this, in turn, leads to an increase in porosity and a reduction in compressive strength. In terms of shrinkage behavior under free conditions, mixtures with increasing replacement ratios of cementitious materials saw increasing shrinkage, with the HSC containing EAS being similar to the other specimens. The mixtures containing EAS saw a quite gradual decrease in their freezing and thawing resistance properties as the number of freeze-thaw cycles they underwent increased. However, the efficacy of HSC with less than 15% of EAS is similar to GBS; hence, EAS could replace cement in concrete for certain applications, which would lead to more environmental benefits.

Effect of Co3O4 Nanoparticles on Improving Catalytic Behavior of Pd/Co3O4@MWCNT Composites for Cathodes in Direct Urea Fuel Cells.

Direct urea fuel cells (DUFCs) have recently drawn increased attention as sustainable power generation devices because of their considerable advantages. Nonetheless, the kinetics of the oxidation-reduction reaction, particularly the electrochemical oxidation and oxygen reduction reaction (ORR), in direct urea fuel cells are slow and hence considered to be inefficient. To overcome these disadvantages in DUFCs, Pd nanoparticles loaded onto Co3O4 supported by multi-walled carbon nanotubes (Pd/Co3O4@MWCNT) were employed as a promising cathode catalyst for enhancing the electrocatalytic activity and oxygen reduction reaction at the cathode in DUFCs. Co3O4@MWCNT and Pd/Co3O4@MWCNT were synthesized via a facile two-step hydrothermal process. A Pd/MWCNT catalyst was also prepared and evaluated to study the effect of Co3O4 on the performance of the Pd/Co3O4@MWCNT catalyst. A current density of 13.963 mA cm-2 and a maximum power density of 2.792 mW cm-2 at 20 °C were obtained. Pd/Co3O4@MWCNT is a prospectively effective cathode catalyst for DUFCs. The dilution of Pd with non-precious metal oxides in adequate amounts is economically conducive to highly practical catalysts with promising electrocatalytic activity in fuel cell applications.

Data on the observation of the interface between lithium phosphorus oxynitride film and lithium layer.

This data provides the observation of the interface between lithium phosphorus oxynitride(LiPON) film and lithium layer. In other words, the shape of the lithium electrode protected by the LiPON film after the dissolution/precipitation cycle is provided as images. Also, for clear interpretation of these images, the shape of lithium formed between LiPON and copper current collector is provided as images. Readers are requested to go through the article entitled "Suppression of formation of lithium dendrite via surface modification by 2-D lithium phosphorus oxynitride as a highly stable anode for metal lithium batteries" (Ko et al., 2020) for further interpretation and discussion. Since the article provided only surface images for the above-mentioned items, it is expected that the cross-sectional images provided in this data will help readers to understand the overall contents in depth.

Effect of Strengthening Methods on Two-Way Slab under Low-Velocity Impact Loading.

In this study, the performance of reinforced concrete slabs strengthened using four methods was investigated under impact loads transferred from the top side to bottom side. The top and bottom sides of test slabs were strengthened by no-slump high-strength, high-ductility concrete (NSHSDC), fiber-reinforced-polymer (FRP) sheet, and sprayed FRP, respectively. The test results indicated that the test specimens strengthened with FRP series showed a 4% increase in reaction force and a decrease in deflection by more than 20% compared to the non-strengthened specimens. However, the specimen enhanced by the NSHSDC jacket at both the top and bottom sides exhibited the highest reaction force and energy dissipation as well as the above measurements because it contains two types of fibers in the NSHSDC. In addition, the weight loss rate was improved by approximately 0.12% for the NSHSDC specimen, which was the lowest among the specimens when measuring the weight before and after the impact load. Therefore, a linear relationship between the top and bottom strengthening of the NSHSDC and the impact resistance was confirmed, concluding that the NSHSDC is effective for impact resistance when the top and bottom sides are strengthened. The results of the analysis of the existing research show that the NSHSDC is considered to have high impact resistance, even though it has lower resistance than the steel fiber reinforced concrete and ultra-high-performance-concrete, it can be expected to further studies on strengthening of NSHSDC.

Enhanced Electrochemical Properties of Catalyst by Phosphorous Addition for Direct Urea Fuel Cell.

An anode bimetallic catalyst comprising Ni-Pd alloy nanoparticles was loaded on acid-treated multi-walled carbon nanotubes (MWCNTs) for application in a direct urea fuel cell. The bimetallic catalyst and MWCNTs were synthesized by a hydrothermal method at 160°C for 5 h. To reduce the catalyst particle size, alkaline resistance, and facilitate their uniform distribution on the surface of the MWCNTs, phosphorus (P) was added to the Ni-Pd/MWCNT catalyst. The effects of P on the distribution and reduction in size of catalyst particles were investigated by Brunauer-Emmett-Teller analysis, transmission electron microscopy, and X-ray diffraction analysis. The enhanced catalytic activity and durability of the P-containing catalyst was confirmed by the high current density [1897.76 mA/cm2 (vs. Ag/AgCl)] obtained at 0.45 V in a 3 M KOH/1.0 M urea alkaline aqueous solution compared with that of the catalyst without P [604.87 mA/cm2 (vs. Ag/AgCl)], as determined by cyclic voltammetry and chronoamperometry. A Urea-O2 fuel cell assembled with a membrane electrode assembly comprising the Ni-Pd(P)/MWCNT catalyst delivered peak power densities of 0.756 and 3.825 mW/cm2 at 25 and 60°C, respectively, in a 3 M KOH/1 M urea solution.

Quaternized Chitosan-Based Anion Exchange Membrane Composited with Quaternized Poly(vinylbenzyl chloride)/Polysulfone Blend.

An efficient and effective process for the production of high-performance anion exchange membranes (AEMs) is necessary for the commercial application of fuel cells. Therefore, in this study, quaternized poly vinylbenzyl chloride (QVBC) and polysulfone were composited with glycidyltrimethylammonium-chloride-quaternized chitosan (QCS) at different ratios (viz., 1 wt %, 5 wt %, and 10 wt %). The structure and morphology of the membranes were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy, respectively. Further, the water uptake, swelling ratio, and ionic conductivities of the composite membrane at different wt % of QCS were evaluated. The membrane with 5% QCS exhibited an ionic conductivity of 49.6 mS/cm and 130 mS/cm at 25 °C and 70 °C, respectively.