Optimizing refuse-derived fuel production from scheduled wastes through Aspen plus simulation.

This study aims to improve the quality of fuel with high calorific value namely Sfuel - a commercial high-quality refuse-derived fuel (RDF) from hazardous waste via modifying the process design and operating parameters of thermal conversion process. The study analyses key parameters of RDF quality, such as calorific value and heavy metal content, before and after process modifications based on the combination of experimental and simulation using Aspen Plus. In this study, the temperature and pressure of the simulation system are varied from 100 to 700 °C and from 1 to 5 bar, respectively. Findings indicate that there are a total of eleven heavy metals and 179 volatile compounds in the "Sfuels". The quality of the targeted product is greatly improved by the metal evaporation at high temperatures and pressures. However, the calorific value of RDF significantly decreases at 700 °C due to a large amount of the carbon content being evaporated. Although the carbon content at high temperatures is significantly lost, the heat from the vapour stream reactor outlet, which is reused to preheat the nitrogen gas stream supplied to the system, reduces energy consumption while improving the thermal conversion efficiency of the system. Besides, low pressure along with high temperature are not the optimal conditions for quality Sfuels improvement by thermal conversion. Results also indicate that electric heating is more economically efficient than natural gas heating.

Sustainable grain production growth of farmland-A role of agricultural socialized services.

The main aim of this study is to examine the evolving landscape of agricultural socialized services and their impact on the consistent growth of grain production in China. Using panel data from 2007 to 2020, we employ the Entropy Method to gauge the dynamic changes in agricultural socialized services that have contributed to the steady increase in grain production. The research methods include static panel, mediator, and threshold regression models to investigate the effects and mechanisms underpinning the improvement of agricultural socialized services on grain production growth. The empirical findings demonstrate a significantly positive correlation between enhanced agricultural socialized services, such as means of production services, sci-tech information services, and social public services, and increased grain production. This positive impact persists even with limited grain production resources. A mediating effect was identified, whereby agricultural socialized services indirectly stimulate grain production growth by encouraging large-scale agricultural land management. Furthermore, threshold analysis indicates the presence of a single threshold effect linked to the level of agricultural socialization services. This threshold effect plays a pivotal role in the relationship between large-scale agricultural management and steady grain production growth. The study suggests an enhancement of agricultural socialized services can promote sustained growth in grain production.

Solving the fouling mechanisms in composite membranes for water purification: An advance approach.

With the increasing population worldwide more wastewater is created by human activities and discharged into the waterbodies. This is causing the contamination of aquatic bodies, thus disturbing the marine ecosystems. The rising population is also posing a challenge to meet the demands of fresh drinking water in the water-scarce regions of the world, where drinking water is made available to people by desalination process. The fouling of composite membranes remains a major challenge in water desalination. In this innovative study, we present a novel probabilistic approach to analyse and anticipate the predominant fouling mechanisms in the filtration process. Our establishment of a robust theoretical framework hinges upon the utilization of both the geometric law and the Hermia model, elucidating the concept of resistance in series (RIS). By manipulating the transmembrane pressure, we demonstrate effective management of permeate flux rate and overall product quality. Our investigations reveal a decrease in permeate flux in three distinct phases over time, with the final stage marked by a significant reduction due to the accumulation of a denser cake layer. Additionally, an increase in transmembrane pressure leads to a correlative rise in permeate flux, while also exerting negative effects such as membrane ruptures. Our study highlights the minimal immediate impact of the intermediate blocking mechanism (n = 1) on permeate flux, necessitating continuous monitoring for potential long-term effects. Additionally, we note a reduced membrane selectivity across all three fouling types (n = 0, n = 1.5, n = 2). Ultimately, our findings indicate that the membrane undergoes complete fouling with a probability of P = 0.9 in the presence of all three fouling mechanisms. This situation renders the membrane unable to produce water at its previous flow rate, resulting in a significant reduction in the desalination plant's productivity. I have demonstrated that higher pressure values notably correlate with increased permeate flux across all four membrane types. This correlation highlights the significant role of TMP in enhancing the production rate of purified water or desired substances through membrane filtration systems. Our innovative approach opens new perspectives for water desalination management and optimization, providing crucial insights into fouling mechanisms and proposing potential strategies to address associated challenges.

A sustainable approach for fluoride treatment using coconut fiber cellulose as an adsorbent.

In developing countries like India, an economically viable and ecologically approachable strategy is required to safeguard the drinking water. Excessive fluoride intake through drinking water can lead to dental fluorosis, skeletal fluorosis, or both. The present study has been under with an objective to investigate the feasibility of using cellulose derived from coconut fiber as an adsorbent under varying pH conditions for fluoride elimination from water. The assessment of equilibrium concentration of metal ions using adsorption isotherms is an integral part of the study. This present finding indicates the considerable effect of variation of adsorbent dosages on the fluoride removal efficiency under constant temperature conditions of 25 ± 2 °C with a contact period of 24 h. It is pertinent to mention that maximum adsorption of 88% has been observed with a pH value of 6 with 6 h time duration with fluoride dosage of 50 mg/L. The equilibrium concentration dwindled to 0.4 mg/L at fluoride concentration of 20 mg/L. The Langmuir model designates the adsorption capacity value of 2.15 mg/L with initial fluoride concentration of 0.21 mg/g with R2 value of 0.660. Similarly, the adsorption capacity using Freundlich isotherms is found to be 0.58 L/g and 0.59 L/g with fluoride concentration of 1.84 mg/L and 2.15 mg/L respectively. The results from the present study confirm that coconut fiber possesses appropriate sorption capabilities of fluoride ion but is a pH dependent phenomenon. The outcomes of the study indicate the possible use of cellulose extracted from waste coconut fiber as a low-cost fluoride adsorbent. The present study can be well implemented on real scale systems as it will be beneficial economically as well as environmentally.

Optimization of syngas production from co-gasification of palm oil decanter cake and alum sludge: An RSM approach with char characterization.

The study explores co-gasification of palm oil decanter cake and alum sludge, investigating the correlation between input variables and syngas production. Operating variables, including temperature (700-900 °C), air flow rate (10-30 mL/min), and particle size (0.25-2 mm), were optimized to maximize syngas production using air as the gasification agent in a fixed bed horizontal tube furnace reactor. Response Surface Methodology with the Box-Behnken design was used employed for optimization. Fourier Transformed Infra-Red (FTIR) and Field Emission Scanning Electron Microscopic (FESEM) analyses were used to analyze the char residue. The results showed that temperature and particle size have positive effects, while air flow rate has a negative effect on the syngas yield. The optimal CO + H2 composition of 39.48 vol% was achieved at 900 °C, 10 mL/min air flow rate, and 2 mm particle size. FTIR analysis confirmed the absence of C─Cl bonds and the emergence of Si─O bonds in the optimized char residue, distinguishing it from the raw sample. FESEM analysis revealed a rich porous structure in the optimized char residue, with the presence of calcium carbonate (CaCO3) and aluminosilicates. These findings provide valuable insights for sustainable energy production from biomass wastes.

Brassinosteroid Signaling Pathways: Insights into Plant Responses under Abiotic Stress.

With the growing global population, abiotic factors have emerged as a formidable threat to agricultural food production. If left unaddressed, these stress factors might reduce food yields by up to 25% by 2050. Plants utilize natural mechanisms, such as reactive oxygen species scavenging, to mitigate the adverse impacts of abiotic stressors. Diverse plants exhibit unique adaptations to abiotic stresses, which are regulated by phytohormones at various levels. Brassinosteroids (BRs) play a crucial role in controlling essential physiological processes in plants, including seed germination, xylem differentiation, and reproduction. The BR cascade serves as the mechanism through which plants respond to environmental stimuli, including drought and extreme temperatures. Despite two decades of research, the complex signaling of BRs under different stress conditions is still being elucidated. Manipulating BR signaling, biosynthesis, or perception holds promise for enhancing crop resilience. This review explores the role of BRs in signaling cascades and summarizes their substantial contribution to plants' ability to withstand abiotic stresses.

Exploring the Effects of Selenium and Brassinosteroids on Photosynthesis and Protein Expression Patterns in Tomato Plants under Low Temperatures.

This study aimed to assess the effects of low-temperature stress on two tomato cultivars (S-22 and PKM-1) treated with 24-epibrassinolide (EBL) and selenium (Se) by determining the changes in the proteomics profiles, growth biomarkers, biochemical parameters, and physiological functions. The growth parameters, photosynthetic traits, and activity of nitrate reductase in the S-22 and PKM-1 plants were markedly reduced by exposure to low temperatures. However, the combined application of EBL and Se under different modes significantly enhanced the aforementioned parameters under stress and non-stress conditions. Exposure to low temperatures increased the activities of the antioxidant enzymes (catalase, peroxidase, and superoxide dismutase) and the proline content of leaves, which were further enhanced by treatment with Se and EBL in both varieties. This research sheds light on the potential for employing exogenous EBL and Se as crucial biochemical tactics to assist tomato plants in surviving low-temperature stress. Moreover, the differentially expressed proteins that were involved in plant metabolism following the combined application of EBL and Se under low-temperature stress were additionally identified. Functional analysis revealed that the Q54YH4 protein plays an active role against plant stressors. The conserved regions in the protein sequences were analyzed for assessing the reliability of plant responses against the external application of EBL and Se under low temperatures.

Influence of fly ash on thermo-mechanical and mechanical behavior of injection molded polypropylene matrix composites.

Polypropylene composites find widespread application in industries, including packaging, plastic parts, automotive, textiles, and specialized devices like living hinges known for their remarkable flexibility. This study focuses on the manufacturing of polypropylene composite specimens by incorporating varying weight percentages of fly ash particles with polypropylene using a twin-screw extruder and injection molding machine. The composites were comprehensively tested, evaluating tensile, compressive, and flexural strength, solid-state and polymer melt properties, modulus, damping, and thermal response. The findings reveal that the compressive strength of polypropylene increases up to 2 wt% of added fly ash particles and subsequently exhibits a slight decline. Tensile strength demonstrates an increase up to 1 wt% of fly ash, followed by a decrease with a 2 wt% addition, and then a subsequent increase. Flexural strength shows improvement up to 3 wt% fly ash addition before declining. The storage modulus curve is categorized into three regions: the glassy region (up to 0 °C), the glass transition region (0-50 °C), and the glass transition region of polypropylene (>50 °C), each corresponding to different molecular motions. Weight loss curves exhibit similar trends, indicating uniform pyrolysis behavior attributed to consistent chemical bonds. Plastic degradation commences around 440 °C and concludes near 550 °C. Additionally, elemental mapping of fly ash composition identified various elements such as O, Si, K, Mg, Ca, Cl, Na, P, Al, Fe, S, Cu, Ti, and Ni. These findings offer valuable insights into the mechanical and thermal properties of polypropylene composites reinforced with fly ash, rendering them suitable for a wide range of industrial applications necessitating strength and durability across temperature variations.

Integrating of electrocoagulation process with submerged membrane bioreactor for wastewater treatment under low voltage gradients.

Treating and reusing wastewater has become an essential aspect of water management worldwide. However, the increase in emerging pollutants such as polycyclic aromatic hydrocarbons (PAHs), which are presented in wastewater from various sources like industry, roads, and household waste, makes their removal difficult due to their low concentration, stability, and ability to combine with other organic substances. Therefore, treating a low load of wastewater is an attractive option. The study aimed to address membrane fouling in the submerged membrane bioreactor (SMBR) used for wastewater treatment. An aluminum electrocoagulation (EC) device was combined with SMBR as a pre-treatment to reduce fouling. The EC-SMBR process was compared with a conventional SMBR without EC, fed with real grey water. To prevent impeding biological growth, low voltage gradients were utilized in the EC deviceThe comparison was conducted over 60 days with constant transmembrane pressure and infinite solid retention time (SRT). In phase I, when the EC device was operated at a low voltage gradient (0.64 V/cm), no significant improvement in the pollutants removal was observed in terms of color, turbidity, and chemical oxygen demand (COD). Nevertheless, during phase II, a voltage gradient of 1.26 V/cm achieved up to 100%, 99.7%, 92%, 94.1%, and 96.5% removals in the EC-SMBR process in comparison with 95.1%, 95.4%, 85%, 91.7% and 74.2% removals in the SMBR process for turbidity, color, COD, ammonia nitrogen (NH3-N), total phosphorus (TP), respectively. SMBR showed better anionic surfactant (AS) removal than EC-SMBR. A voltage gradient of 0.64 V/cm in the EC unit significantly reduced fouling by 23.7%, while 1.26 V/cm showed inconsistent results. Accumulation of Al ions negatively affected membrane performance. Low voltage gradients in EC can control SMBR fouling if Al concentration is controlled. Future research should investigate EC-SMBR with constant membrane flux for large-scale applications, considering energy consumption and operating costs.

Controlled Synthesis and Uniform Anchoring of Hollow CuxO Nanocubes on Carbon Nanofiber for Enhanced Se(S)-Se(S) Bond Activation.

In the present study, we fabricated hollow cubic CuxO nanoparticles (∼23 nm) incorporated with CNF (HC-CuxO/CNF) through controlled thermal oxidation of solid cubic Cu2O nanoparticles (∼21 nm) supported on carbon nanofibers (SC-Cu2O/CNF) under airflow, exploiting the nanoscale Kirkendall effect. These hollow CuxO nanocubes with increased surface areas exhibited outstanding catalytic activity for unsymmetrical chalcogenide synthesis under ligand-free conditions.

Development and Antibacterial Investigation of Linezolid-Loaded SPIONs and HPLC Method Development for Quantitative Analysis of Linezolid.

BACKGROUND: Linezolid (LNZ) is extremely prone to resistance. The development of resistance to LNZ should be taken into consideration when selecting this drug as a therapeutic option. It is well established that reactive oxygen species (ROS) generated by iron oxide nanoparticles (MNPs) could kill the infecting bacteria. So, we hypothesized the synergistic antibacterial effect of iron oxide nanoparticles and LNZ. OBJECTIVE: To study the release and antibacterial effects of LNZ-loaded superparamagnetic iron oxide nanoparticles (SPIONs) on Staphylococcus aureus and Streptococcus pneumoniae. METHOD: Ferrofluid containing SPIONs was synthesized via chemical co-precipitation method and stabilized by sodium lauryl sulphate (SLS). SPIONs were then loaded with LNZ and characterized for particle size, FT-IR, XRD, and entrapment efficiency. Further antibacterial activity of SPIONs and LNZ-loaded SPIONs was investigated. For the in vitro release findings, HPLC analytical method development and validation were performed. RESULTS: Isolation of LNZ was accomplished on a C-18 column with methanol-TBHS (tetra butyl ammonium hydrogen sulphate, 50:50, v/v). The eluate was monitored at 247 nm with a retention time of 4.175 min. The MNP's DLS measurement revealed monodispersed particles with an average size of 16.81 ± 1.07 nm and PDI 0.176 ± 0.012. In optimized formulation, 25 ± 1.75% (w/w) of the drug was found to be entrapped. XRD revealed uniform coating of oleic acid covering the entire magnetic particles' surface with no change in its crystallinity. An effective antimicrobial activity was observed at the lowered dose of drug. CONCLUSIONS: A robust HPLC method was developed to quantify the LNZ in MNPs, and outcomes showed that the reduced dose of LNZ incorporated in SPIONs was able to show similar activity as the marketed product. HIGHLIGHTS: Successfully reduction of the dose of LNZ was established with the aid of biocompatible MNPs to attain the equivalent antibacterial activity.

Exploring the potential of metal and metal oxide nanomaterials for sustainable water and wastewater treatment: A review of their antimicrobial properties.

Metallic nanoparticles (NPs) are of particular interest as antimicrobial agents in water and wastewater treatment due to their broad suppressive range against bacteria, viruses, and fungi commonly found in these environments. This review explores the potential of different types of metallic NPs, including zinc oxide, gold, copper oxide, and titanium oxide, for use as effective antimicrobial agents in water and wastewater treatment. This is due to the fact that metallic NPs possess a broad suppressive range against bacteria, viruses, as well as fungus. In addition to that, NPs are becoming an increasingly popular alternative to antibiotics for treating bacterial infections. Despite the fact that most research has been focused on silver NPs because of the antibacterial qualities that are known to be associated with them, curiosity about other metallic NPs as potential antimicrobial agents has been growing. Zinc oxide, gold, copper oxide, and titanium oxide NPs are included in this category since it has been demonstrated that these elements have antibacterial properties. Inducing oxidative stress, damage to the cellular membranes, and breakdowns throughout the protein and DNA chains are some of the ways that metallic NPs can have an influence on microbial cells. The purpose of this review was to engage in an in-depth conversation about the current state of the art regarding the utilization of the most important categories of metallic NPs that are used as antimicrobial agents. Several approaches for the synthesis of metal-based NPs were reviewed, including physical and chemical methods as well as "green synthesis" approaches, which are synthesis procedures that do not involve the employment of any chemical agents. Moreover, additional pharmacokinetics, physicochemical properties, and the toxicological hazard associated with the application of silver NPs as antimicrobial agents were discussed.

Recent advances in the biocatalytic mitigation of emerging pollutants: A comprehensive review.

The issue of environmental pollution has been worsened by the emergence of new contaminants whose morphology is yet to be fully understood . Several techniques have been adopted to mitigate the pollution effects of these emerging contaminants, and bioremediation involving plants, microbes, or enzymes has stood out as a cost-effective and eco-friendly approach. Enzyme-mediated bioremediation is a very promising technology as it exhibits better pollutant degradation activity and generates less waste. However, this technology is subject to challenges like temperature, pH, and storage stability, in addition to recycling difficulty as it is arduous to isolate them from the reaction media. To address these challenges, the immobilization of enzymes has been successfully applied to ameliorate the activity, stability, and reusability of enzymes. Although this has significantly increased the uses of enzymes over a wide range of environmental conditions and facilitated the use of smaller bioreactors thereby saving cost, it still comes with additional costs for carriers and immobilization. Additionally, the existing immobilization methods have their individual limitations. This review provides state-of-the-art information to readers focusing on bioremediation using enzymes. Different parameters such as: the sustainability of biocatalysts, the ecotoxicological evaluation of transformation contaminants, and enzyme groups used were reviewed. The efficacy of free and immobilized enzymes, materials and methods for immobilization, bioreactors used, challenges to large-scale implementation, and future research needs were thoroughly discussed.

Evaluating ionic liquids for its potential as eco-friendly solvents for naproxen removal from water sources using COSMO-RS: Computational and experimental validation.

An emerging contaminant of concern in aqueous streams is naproxen. Due to its poor solubility, non-biodegradability, and pharmaceutically active nature, the separation is challenging. Conventional solvents employed for naproxen are toxic and harmful. Ionic liquids (ILs) have attracted great attention as greener solubilizing and separating agent for various pharmaceuticals. ILs have found extensive usage as solvents in nanotechnological processes involving enzymatic reactions and whole cells. The employment of ILs can enhance the effectiveness and productivity of such bioprocesses. To avoid cumbersome experimental screening, in this study, conductor like screening model for real solvents (COSMO-RS) was used to screen ILs. Thirty anions and eight cations from various families were chosen. Activity coefficient at infinite dilution, capacity, selectivity, performance index, molecular interactions using σ-profiles and interaction energies were used to make predictions about solubility. According to the findings, quaternary ammonium cations, highly electronegative, and food-grade anions will form excellent ionic liquid combinations for solubilizing naproxen and hence will be better separating agents. This research will contribute easy designing of ionic liquid-based separation technologies for naproxen. In different separation technologies, ionic liquids can be employed as extractants, carriers, adsorbents, and absorbents.

MXenes and MXene-based materials for removal of pharmaceutical compounds from wastewater: Critical review.

The rapid increase in the global population and its ever-rising standards of living are imposing a huge burden on global resources. Apart from the rising energy needs, the demand for freshwater is correspondingly increasing. A population of around 3.8 billion people will face water scarcity by 2030, as per the reports of the World Water Council. This may be due to global climate change and the deficiency in the treatment of wastewater. Conventional wastewater treatment technologies fail to completely remove several emerging contaminants, especially those containing pharmaceutical compounds. Hence, leading to an increase in the concentration of harmful chemicals in the human food chain and the proliferation of several diseases. MXenes are transition metal carbide/nitride ceramics that primarily structure the leading 2D material group. MXenes act as novel nanomaterials for wastewater treatment due to their high surface area, excellent adsorption properties, and unique physicochemical properties, such as high electrical conductivity and hydrophilicity. MXenes are highly hydrophilic and covered with active functional groups (i.e., hydroxyl, oxygen, fluorine, etc.), which makes them efficient adsorbents for a wide range of species and promising candidates for environmental remediation and water treatment. This work concludes that the scaling up process of MXene-based materials for water treatment is currently of high cost. The up-to-date applications are still limited because MXenes are currently produced mainly in the laboratory with limited yield. It is recommended to direct research efforts towards lower synthesis cost procedures coupled with the use of more environmentally friendly materials to avoid secondary contamination.

Contemporary avenues of the Hydrogen industry: Opportunities and challenges in the eco-friendly approach.

Hydrogen (H2) is a possible energy transporter and feedstock for energy decarbonization, transportation, and chemical sectors while reducing global warming's consequences. The predominant commercial method for producing H2 today is steam methane reforming (SMR). However, there is still room for development in process intensification, energy optimization, and environmental concerns related to CO2 emissions. Reactors using metallic membranes (MRs) can handle both problems. Compared to traditional reactors, MRs operates at substantially lower pressures and temperatures. As a result, capital and operational costs may be significantly cheaper than traditional reactors. Furthermore, metallic membranes (MMs), particularly Pd and its alloys, naturally permit only H2 permeability, enabling the production of a stream with a purity of up to 99.999%. This review describes several methods for H2 production based on the energy sources utilized. SRM with CO2 capture and storage (CCUS), pyrolysis of methane, and water electrolysis are all investigated as process technologies. A debate based on a color code was also created to classify the purity of H2 generation. Although producing H2 using fossil fuels is presently the least expensive method, green H2 generation has the potential to become an affordable alternative in the future. From 2030 onward, green H2 is anticipated to be less costly than blue hydrogen. Green H2 is more expensive than fossil-based H2 since it uses more energy. Blue H2 has several tempting qualities, but the CCUS technology is pricey, and blue H2 contains carbon. At this time, almost 80-95% of CO2 can be stored and captured by the CCUS technology. Nanomaterials are becoming more significant in solving problems with H2 generation and storage. Sustainable nanoparticles, such as photocatalysts and bio-derived particles, have been emphasized for H2 synthesis. New directions in H2 synthesis and nanomaterials for H2 storage have also been discussed. Further, an overview of the H2 value chain is provided at the end, emphasizing the financial implications and outlook for 2050, i.e., carbon-free H2 and zero-emission H2.

Electrospun Fe doped TiO2 fiber photocatalyst for efficient wastewater treatment.

Water pollution caused by industrial wastewater is the most critical environmental problem in the world. Synthetic dyes are commonly used in various industries such as paper, plastic, printing, leather and textile for their ability to impact color. Complex composition, high toxicity and low biodegradability of dyes make them difficult to degrade which causes a substantial negative impact on overall ecosystems. To address this issue we synthesized TiO2 fibers photocatalyst using the combination of sol-gel and electrospinning techniques to be used in the degradation of dyes which causes water pollution. We doped Fe in TiO2 fibers to enhance the absorption in the visible region of the solar spectrum which will also help to increase the degradation efficiency. As synthesized pristine TiO2 fibers and Fe doped TiO2 fibers were analyzed using different characterization techniques such as X-ray diffraction, Scanning electron microscopy, Transmission electron microscopy, UV-Visible spectroscopy, X-ray photoelectron spectroscopy. 5% Fe doped TiO2 fibers show excellent photocatalytic degradation activity for rhodamine B (99% degradation in 120 min). It can be utilized for degradation of other dye pollutants such as methylene blue, Congo red and methyl orange. It shows good photocatalytic activity (97%) even after 5 cycles of reuse. The radical trapping experiments reveals that holes, •O2- and •OH has a significant contribution in the photocatalytic degradation. Due to the robust fibrous nature of 5FeTOF the process of collection of photocatalysts was simple and without loss as compared to powder photocatalysts. This justifies our selection of electrospinning method of synthesis of 5FeTOF which is also useful for large scale production.

Emerging waste-to-wealth applications of fly ash for environmental remediation: A review.

The considerable increase in world energy consumption owing to rising global population, intercontinental transportation and industrialization has posed numerous environmental concerns. Particularly, in order to meet the required electricity supply, thermal power plants for electricity generation are widely used in many countries. However, an annually excessive quantity of waste fly ash up to 1 billion tones was globally discarded from the combustion of various carbon-containing feedstocks in thermoelectricity plants. About half of the industrially generated fly ash is dumped into landfills and hence causing soil and water contamination. Nonetheless, fly ash still contains many valuable components and possesses outstanding physicochemical properties. Utilizing waste fly ash for producing value-added products has gained significant interests. Therefore, in this work, we reviewed the current implementation of fly ash-derived materials, namely, zeolite and geopolymer as efficient adsorbents for the environmental treatment of flue gas and polluted water. Additionally, the usage of fly ash as a catalyst support for the photodegradation of organic pollutants and reforming processes for the corresponding wastewater remediation and H2 energy generation is thoroughly covered. In comparison with conventional carbon-based adsorbents, fly ash-derived geopolymer and zeolite materials reportedly exhibited greater heavy metal ions removal and reached the maximum adsorption capacity of about 150 mg g-1. As a support for biogas reforming process, fly ash could enhance the activity of Ni catalyst with 96% and 97% of CO2 and CH4 conversions, respectively.

Electrocatalytic Oxygen Reduction Reaction of Graphene Oxide and Metal-Free Graphene in an Alkaline Medium.

Graphene is a well-known two-dimensional material with a large surface area and is used for numerous applications in a variety of fields. Metal-free carbon materials such as graphene-based materials are widely used as an electrocatalyst for oxygen reduction reactions (ORRs). Recently, more attention has been paid to developing metal-free graphenes doped with heteroatoms such as N, S, and P as efficient electrocatalysts for ORR. In contrast, we found our prepared graphene from graphene oxide (GO) by the pyrolysis method under a nitrogen atmosphere at 900 °C has shown better ORR activity in aqueous 0.1 M potassium hydroxide solution electrolyte as compared with the electrocatalytic activity of pristine GO. At first, we prepared various graphene by pyrolysis of 50 mg and 100 mg of GO in one to three alumina boats and pyrolyzed the samples under a N2 atmosphere at 900 °C. The prepared samples are named G50-1B to 3B and G100-1B and G100-2B. The prepared GO and graphenes were also analyzed under various characterization techniques to confirm their morphology and structural integrity. The obtained results suggest that the ORR electrocatalytic activity of graphene may differ based on the pyrolysis conditions. We found that G100-1B (Eonset, E1/2, JL, and n values of 0.843, 0.774, 4.558, and 3.76) and G100-2B (Eonset, E1/2, and JL values of 0.837, 0.737, 4.544, and 3.41) displayed better electrocatalytic ORR activity, as did Pt/C electrode (Eonset, E1/2, and JL values of 0.965, 0.864, 5.222, and 3.71, respectively). These results display the wide use of the prepared graphene for ORR and also can be used for fuel cell and metal-air battery applications.

Synergy of silica sand and waste plastics as thermoplastic composites on abrasive wear characteristics under conditions of different loads and sliding speeds.

The diverse nature of polymers with attractive properties has replaced the conventional materials with polymeric composites. The present study was sought to evaluate the wear performance of thermoplastic-based composites under the conditions of different loads and sliding speeds. In the present study, nine different composites were developed by using low-density polyethylene (LDPE), high-density polyethylene (HDPE) and polyethylene terephthalate (PET) with partial sand replacements i.e., 0, 30, 40, and 50 wt%. The abrasive wear was evaluated as per the ASTM G65 standard test for abrasive wear through a dry-sand rubber wheel apparatus under the applied loads of 34.335, 56.898, 68.719, 79.461 and 90.742 (N) and sliding speeds of 0.5388, 0.7184, 0.8980, 1.0776 and 1.4369 (m/s). The optimum density and compressive strength were obtained to be 2.0555 g/cm3 and 46.20 N/mm2, respectively for the composites HDPE60 and HDPE50 respectively. The minimum value of abrasive wear were found to 0.02498, 0.03430, 0.03095, 0.09020 and 0.03267 (cm3) under the considered loads of 34.335, 56.898, 68.719, 79.461 and 90.742 (N), respectively. Moreover, the composites LDPE50, LDPE100, LDPE100, LDPE50PET20 and LDPE60 showed a minimum abrasive wear of 0.03267, 0.05949, 0.05949, 0.03095 and 0.10292 at the sliding speeds of 0.5388, 0.7184, 0.8980, 1.0776 and 1.4369 (m/s), respectively. The wear response varied non-linearly with the conditions of loads and sliding speeds. Micro-cutting, plastic deformations, fiber peelings, etc. were included as the possible wear mechanism. The possible correlations between wear and mechanical properties, and throughout discussions for wear behaviors through the morphological analyses of the worn-out surfaces were provided.