RESUMO
Carbon nanoallotropes are important nanomaterials with unusual properties and promising applications. High pressure synthesis has the potential to open new avenues for controlling and designing their physical and chemical characteristics for a broad range of uses but it remains little understood due to persistent conceptual and experimental challenges, in addition to fundamental physics and chemistry questions that are still unresolved after many decades. Here we demonstrate sub-nanosecond nanocarbon synthesis through the application of laser-induced shock-waves to a prototypical organic carbon-rich liquid precursor-liquid carbon monoxide. Overlapping large-scale molecular dynamics simulations capture the atomistic details of the nanoparticles' formation and evolution in a reactive environment and identify classical evaporation-condensation as the mechanism governing their growth on these time scales.
RESUMO
The chemical and physical processes involved in the shock-to-detonation transition of energetic solids are not fully understood due to difficulties in probing the fast dynamics involved in initiation. Here, we employ shock interferometry experiments with sub-20-ps time resolution to study highly textured (110) pentaerythritol tetranitrate (PETN) thin films during the early stages of shock compression using ultrafast laser-driven shock wave methods. We observe evidence of rapid exothermic chemical reactions in the PETN thin films for interface particle velocities above â¼1.05 km/s as indicated by shock velocities and pressures well above the unreacted Hugoniot. The time scale of our experiment suggests that exothermic reactions begin less than 50 ps behind the shock front for these high-density PETN thin films. Thermochemical calculations for partially reacted Hugoniots also support this interpretation. The experimentally observed time scale of reactivity could be used to narrow possible initiation mechanisms.
RESUMO
Ammonium perchlorate NH4ClO4 (AP) was studied using synchrotron angle-dispersive X-ray powder diffraction (XRPD) and Raman spectroscopy. A diamond-anvil cell was used to compress AP up to 50 GPa at room temperature (RT). Density functional theory (DFT) calculations were performed to provide further insight and comparison to the experimental data. A high-pressure barite-type structure (Phase II) forms at ≈4 GPa and appears stable up to 40 GPa. Refined atomic coordinates for Phase II are provided, and details for the Phase I â II transition mechanics are outlined. Pressure-dependent enthalpies computed for DFT-optimized crystal structures confirm the Phase I â II transition sequence, and the interpolated transition pressure is in excellent agreement with the experiment. Evidence for additional (underlying) structural modifications include a marked decrease in the Phase II b'-axis compressibility starting at 15 GPa and an unambiguous stress relaxation in the normalized stress-strain response at 36 GPa. Above 47 GPa, XRD Bragg peaks begin to decrease in amplitude and broaden. The apparent loss of crystalline long-range order likely signals the onset of amorphization. Three isostructural modifications were discovered within Phase II via Raman spectroscopy. A revised RT isothermal phase diagram is discussed based on the findings of this study.
RESUMO
We use a recently developed plasma-flow reactor to experimentally investigate the formation of oxide nanoparticles from gas phase metal atoms during oxidation, homogeneous nucleation, condensation, and agglomeration processes. Gas phase uranium, aluminum, and iron atoms were cooled from 5000 K to 1000 K over short-time scales (∆t < 30 ms) at atmospheric pressures in the presence of excess oxygen. In-situ emission spectroscopy is used to measure the variation in monoxide/atomic emission intensity ratios as a function of temperature and oxygen fugacity. Condensed oxide nanoparticles are collected inside the reactor for ex-situ analyses using scanning and transmission electron microscopy (SEM, TEM) to determine their structural compositions and sizes. A chemical kinetics model is also developed to describe the gas phase reactions of iron and aluminum metals. The resulting sizes and forms of the crystalline nanoparticles (FeO-wustite, eta-Al2O3, UO2, and alpha-UO3) depend on the thermodynamic properties, kinetically-limited gas phase chemical reactions, and local redox conditions. This work shows the nucleation and growth of metal oxide particles in rapidly-cooling gas is closely coupled to the kinetically-controlled chemical pathways for vapor-phase oxide formation.
RESUMO
Using in situ synchrotron x-ray diffraction and Raman spectroscopy in concert with first principles calculations we demonstrate the synthesis of stable Xe(Fe,Fe/Ni)_{3} and XeNi_{3} compounds at thermodynamic conditions representative of Earth's core. Surprisingly, in the case of both the Xe-Fe and Xe-Ni systems Fe and Ni become highly electronegative and can act as oxidants. The results indicate the changing chemical properties of elements under extreme conditions by documenting that electropositive at ambient pressure elements could gain electrons and form anions.
RESUMO
We present the development of a steady state plasma flow reactor to investigate gas phase physical and chemical processes that occur at high temperature (1000 < T < 5000 K) and atmospheric pressure. The reactor consists of a glass tube that is attached to an inductively coupled argon plasma generator via an adaptor (ring flow injector). We have modeled the system using computational fluid dynamics simulations that are bounded by measured temperatures. In situ line-of-sight optical emission and absorption spectroscopy have been used to determine the structures and concentrations of molecules formed during rapid cooling of reactants after they pass through the plasma. Emission spectroscopy also enables us to determine the temperatures at which these dynamic processes occur. A sample collection probe inserted from the open end of the reactor is used to collect condensed materials and analyze them ex situ using electron microscopy. The preliminary results of two separate investigations involving the condensation of metal oxides and chemical kinetics of high-temperature gas reactions are discussed.
RESUMO
Magnesium chloride (MgCl2) with the rhombohedral layered CdCl2-type structure (α-MgCl2) has been studied experimentally using synchrotron angle-dispersive powder x-ray diffraction and Raman spectroscopy using a diamond-anvil cell up to 100 GPa at room temperature and theoretically using first-principles density functional calculations. The results reveal a pressure-induced second-order structural phase transition to a hexagonal layered CdI2-type structure (ß-MgCl2) at 0.7 GPa: the stacking sequence of the Cl anions are altered resulting in a reduction of the c-axis length. Theoretical calculations confirm this phase transition sequence and the calculated transition pressure is in excellent agreement with the experiment. Lattice dynamics calculations also reproduce the experimental Raman spectra measured for the ambient and high-pressure phase. According to our experimental results MgCl2 remains in a 2D layered phase up to 100 GPa and further, the 6-fold coordination of Mg cations is retained. Theoretical calculations of relative enthalpy suggest that this extensive pressure stability is due to a low enthalpy of the layered structure ruling out kinetic barrier effects. This observation is unusual, as it contradicts with the general structural behavior of highly compressed AB2 compounds.
RESUMO
Recent theoretical studies of 2,6-diamino-3,5-dinitropyrazine-1-oxide (C4H4N6O5 Lawrence Livermore Molecule No. 105, LLM-105) report unreacted high pressure equations of state that include several structural phase transitions, between 8 and 50 GPa, while one published experimental study reports equation of state (EOS) data up to a pressure of 6 GPa with no observed transition. Here we report the results of a synchrotron-based X-ray diffraction study and also ambient temperature isobaric-isothermal atomistic molecular dynamics simulations of LLM-105 up to 20 GPa. We find that the ambient pressure phase remains stable up to 20 GPa; there is no indication of a pressure induced phase transition. We do find a prominent decrease in b-axis compressibility starting at approximately 13 GPa and attribute the stiffening to a critical length where inter-sheet distance becomes similar to the intermolecular distance within individual sheets. The ambient temperature isothermal equation of state was determined through refinements of measured X-ray diffraction patterns. The pressure-volume data were fit using various EOS models to yield bulk moduli with corresponding pressure derivatives. We find very good agreement between the experimental and theoretically derived EOS.
RESUMO
Pressure dependent angle-dispersive x-ray powder diffraction measurements of alpha-phase aluminum trifluoride (α-AlF3) and separately, aluminum triiodide (AlI3) were conducted using a diamond-anvil cell. Results at 295 K extend to 50 GPa. The equations of state of AlF3 and AlI3 were determined through refinements of collected x-ray diffraction patterns. The respective bulk moduli and corresponding pressure derivatives are reported for multiple orders of the Birch-Murnaghan (B-M), finite-strain (F-f), and higher pressure finite-strain (G-g) EOS analysis models. Aluminum trifluoride exhibits an apparent isostructural phase transition at approximately 12 GPa. Aluminum triiodide also undergoes a second-order atomic rearrangement: applied stress transformed a monoclinically distorted face centered cubic (fcc) structure into a standard fcc structural arrangement of iodine atoms. Results from semi-empirical thermochemical computations of energetic materials formulated with fluorine containing reactants were obtained with the aim of predicting the yield of halogenated products.
RESUMO
Efforts to synthesize, characterize, and recover novel polynitrogen energetic materials have driven attempts to subject high nitrogen content precursor materials (in particular, metal and nonmetal azides) to elevated pressures. Here we present a combined theoretical and experimental study of the high-pressure behavior of ammonium azide (NH4N3). Using density functional theory, we have considered the relative thermodynamic stability of the material with respect to two other crystal phases, namely, trans-tetrazene (TTZ), and also a novel hydronitrogen solid (HNS) of the form (NH)4, that was recently predicted to become relatively stable under high pressure. Experimentally, we have measured the Raman spectra of NH4N3 up to 71 GPa at room temperature. Our calculations demonstrate that the HNS becomes stable only at pressures much higher (89.4 GPa) than previously predicted (36 GPa). Our Raman spectra are consistent with previous reports up to lower pressures and at higher pressures, while some additional subtle behavior is observed (e.g., mode splitting), there is again no evidence of a phase transition to either TTZ or the HNS.
RESUMO
We apply ultrafast optical interferometry to measure the Hugoniot of an oxygen-balanced mixture of nitromethane and hydrogen peroxide (NM/HP) and compare with Hugoniot data for pure nitromethane (NM) and a 90% hydrogen peroxide/water mixture (HP), as well as theoretical predictions. We observe a 2.1% percent mean pairwise difference between the measured shockwave speed (at the measured piston speed) in unreacted NM/HP and the corresponding "universal" liquid Hugoniot, which is larger than the average standard deviation of our data, 1.4%. Unlike the Hugoniots of both HP and NM, in which measured shock speeds deviate to values greater than the unreacted Hugoniot for piston speeds larger than the respective reaction thresholds, in the NM/HP mixture we observe shock speed deviations to values lower than the unreacted Hugoniot well below the von Neumann pressure (≈28 GPa). Although the trend should reverse for high enough piston speeds, the initial behavior is unexpected. Possible explanations range from mixing effects to a complex index of refraction in the reacted solution. If this is indeed a signature of chemical initiation, it would suggest that the process may not be kinetically limited (on a ~100 ps time scale) between the initiation threshold and the von Neumann pressure.
RESUMO
We report observations of shock compressed, unreacted hydrogen peroxide at pressures up to the von Neumann pressure for a steady detonation wave, using ultrafast laser-driven shock wave methods. At higher laser drive energy we find evidence of exothermic chemical reactivity occurring in less than 100 ps after the arrival of the shock wave in the sample. The results are consistent with our MD simulations and analysis and suggest that reactivity in hydrogen peroxide is initiated on a sub-100 ps time scale under conditions found just subsequent to the lead shock in a steady detonation wave.
RESUMO
We report the adiabatic sound speeds for supercritical fluid carbon monoxide along two isotherms, from 0.17 to 2.13 GPa at 297 K and from 0.31 to 3.2 GPa at 600 K. The carbon monoxide was confined in a resistively heated diamond-anvil cell, and the sound speed measurements were conducted in situ using a recently reported variant of the photoacoustic light scattering effect. The measured sound speeds were then used to parametrize a single site dipolar exponential-6 intermolecular potential for carbon monoxide. PρT thermodynamic states, sound speeds, and shock Hugoniots were calculated using the newly parametrized intermolecular potential and compared to previously reported experimental results. Additionally, we generated an analytical equation of state for carbon monoxide by fitting to a grid of calculated PρT states over a range of 0.1-10 GPa and 150-2000 K. A 2% mean variation was found between computed high-pressure solid-phase densities and measured data-a surprising result for a spherical interaction potential. We further computed a rotationally dependent fluid to ß-solid phase boundary; results signal the relative magnitude of short-range rotational disorder under conditions that span existing phase boundary measurements.
Assuntos
Monóxido de Carbono/química , Temperatura , PressãoRESUMO
Shock compression studies of pressed and confined ultrafine 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) powder were conducted using ultrashort ~300 ps, ~50 GPa shock waves. The recovered decomposition products were characterized using X-ray photoelectron spectroscopy, infrared spectroscopy, and Raman spectroscopy. A substantial amount of shock-related chemistry was observed. Approximately 75% of the nitrogen atoms were liberated as gas-phase species, along with ~33% of the oxygen atoms, as a result of the applied shock. Furthermore, we observe C 1s binding energies suggesting the formation of sp(3) hybridized amorphous carbon. For comparison, a carbon nitride material was also prepared and characterized by thermally pyrolizing TATB. The shock-compressed TATB and the thermally pyrolized TATB are qualitatively different, suggesting that, carbon nitrides, a possible indicator of nitrogen-rich heterocycles precursors, are not a major product class for strongly overdriven shock conditions. These experimental conditions were, however, not detonation conditions, and the possible formation of nitrogen-rich heterocycles in actual detonations still exists.
Assuntos
Lasers , Trinitrobenzenos/química , Nitrilas/química , Espectrofotometria , Espectroscopia de Infravermelho com Transformada de Fourier , Análise Espectral Raman , Termodinâmica , Raios XRESUMO
We have directly resolved shock structures in pure aluminum in the first few hundred picoseconds subsequent to a dynamic load at peak stresses up to 43 GPa and strain rates in excess of 10(10) s(-1). For strong shocks we obtain peak stresses, strain rates, and rise times. From these data, we directly validate the invariance of the dissipative action in the strong shock regime, and by comparing with data obtained at much lower strain rates show that this invariance is observed over at least 5 orders of magnitude in the strain rate. Over the same range, we similarly validate the fourth-power scaling of the strain rate with the peak stress (the Swegle-Grady relation).
RESUMO
Aerogel materials have myriad scientific and technological applications due to their large intrinsic surface areas and ultralow densities. However, creating a nanodiamond aerogel matrix has remained an outstanding and intriguing challenge. Here we report the high-pressure, high-temperature synthesis of a diamond aerogel from an amorphous carbon aerogel precursor using a laser-heated diamond anvil cell. Neon is used as a chemically inert, near-hydrostatic pressure medium that prevents collapse of the aerogel under pressure by conformally filling the aerogel's void volume. Electron and X-ray spectromicroscopy confirm the aerogel morphology and composition of the nanodiamond matrix. Time-resolved photoluminescence measurements of recovered material reveal the formation of both nitrogen- and silicon- vacancy point-defects, suggesting a broad range of applications for this nanocrystalline diamond aerogel.
RESUMO
The effect of pressure on the global thermal decomposition rate of the energetic material HMX was studied. HMX was precompressed in a diamond anvil cell (DAC) and heated at various rates. The parent species population was monitored as a function of time and temperature using Fourier transform infrared (FTIR) spectroscopy. Global decomposition rates were determined by fitting the fraction reacted to the extended-Prout-Tompkins nucleation-growth model and the Friedman isoconversional method. The results of these experiments and analysis indicate that pressure accelerates the decomposition at low-to-moderate pressures (i.e., between ambient pressure and 0.1 GPa) and decelerates the decomposition at higher pressures. The decomposition acceleration is attributed to pressure-enhanced autocatalysis, whereas the deceleration at high pressures is attributed to pressure-inhibiting bond homolysis step(s), which would result in an increase in volume. These results indicate that both the beta- and delta-polymorphs of HMX are sensitive to pressure in the thermally induced decomposition kinetics.
RESUMO
The time scale and/or products of photoinduced decomposition of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) were investigated at ambient pressure and compared with products formed at 8 GPa. Ultrafast time-resolved infrared and steady-state Fourier transform IR (FTIR) spectroscopies were used to probe TATB and its products after photoexcitation with a 5 ns pulse of 532 nm light. At ambient pressure, transient spectra of TATB indicate that the molecule has significantly decomposed within 60 ns; transient spectra also indicate that formation of CO(2), an observed decomposition product, is complete within 30-40 mus. Proof of principle time-resolved experiments at elevated pressures were performed and are discussed briefly. Comparison of steady-state FTIR spectra obtained at ambient and elevated pressure (ca. 8 GPa) indicate that the decomposition products vary with pressure. We find evidence for water as a decomposition product only at elevated pressure.
RESUMO
Characterizing the nature of medium-range order (MRO) in liquids and disordered solids is important for understanding their structure and transport properties. However, accurately portraying MRO, as manifested by the first sharp diffraction peak (FSDP) in neutron and X-ray scattering measurements, has remained elusive for more than 80 years. Here, using X-ray diffraction of amorphous red phosphorus compressed to 6.30 GPa, supplemented with micro-Raman scattering studies, we build three-dimensional structural models consistent with the diffraction data. We discover that the pressure dependence of the FSDP intensity and line position can be quantitatively accounted for by a characteristic void distribution function, defined in terms of average void size, void spacing and void density. This work provides a template to unambiguously interpret atomic and void-space MRO across a broad range of technologically promising network-forming materials.
RESUMO
Phase transitions for CdTe nanoparticles (NPs) under high pressure up to 37.0 GPa have been studied using fluorescence measurements. The phase transition from cinnarbar to rocksalt phase has been observed in CdTe NPs solution at 5.8 GPa, which is much higher than the phase transition pressure of bulk CdTe (3.8 GPa) and that of CdTe NPs in solid form (0.8 GPa). CdTe NPs solution therefore shows elevated phase transition pressure and enhanced stability against pressure compared with bulk CdTe and CdTe NPs in solid forms. The enhanced stability of CdTe NPs solution has been attributed to possible shape change in the phase transition and/or inhomogeneous strains in nanoparticle solutions.