Degradation of hydroxypropyl methylcellulose (HPMC) by acoustic and hydrodynamic cavitation.

The present study aims to investigate the degradation of HPMC on a laboratory scale by acoustic and hydrodynamic cavitation. The effects of temperature and the addition of an external oxidizing agent on the effectiveness of HPMC degradation were systematically investigated by SEC/MALS-RI, FTIR and 1H NMR. The results of the experiments without cavitation show that an external oxidizing agent alone reduces the weight-average molar mass at 60 °C in 30 min for 45.1 % (from 335 to 184 kg mol-1). However, the weight-average molar mass of HPMC decreased significantly more in the cavitation treatment, for 98.8 % (from 335 to 4 kg mol-1) in 30 min at optimal operating conditions of hydrodynamic cavitation (i.e. addition of external oxidant and 60 °C) with a concomitant narrowing of the molar mass distribution, as shown by the dispersity value, which decreased from 2.24 to 1.31. Compared to acoustic cavitation, hydrodynamic cavitation also proved to be more energy efficient. The FTIR spectra of the cavitated HPMC samples without the addition of H2O2 show negligible oxidation of the hydroxyl groups and the glycosidic bonds, confirming that mechanical effects predominate in HPMC degradation in these cases. In contrast, when H2O2 was added, FTIR and 1H NMR show typical signals for cellulose oxidation products, especially when the experiments were performed at 60 °C, confirming that chemical as well as mechanical effects are responsible for the extensive HPMC degradation in these cases. Since treatment methods that lead to lower molar masses and narrower molar mass distributions of the polymers are lacking or require longer treatment times (e.g. 24 h), mechanochemical treatment methods such as cavitation have great potential, as they enable faster polymer degradation (in our case 30 min) through a combination of mechanical and/or chemical degradation mechanisms.

Chemical Recycling of Flexible Polyurethane Foams by Aminolysis to Recover High-Quality Polyols.

Polyurethane foams (PUFs) are widely used commodity materials, but most of them end up in landfills at the end of their life, which is not in line with the circular economy approach. Here, we introduce microwave-assisted aminolysis with amine reagents that contain primary and tertiary amino groups in the structure. These reagents enable complete degradation of the urethane groups in the structure of the flexible PUFs with a much lower amount of degradation reagent than is typically required for solvolysis reactions. The purified, recovered polyols are close equivalents to the corresponding virgin polyols in terms of their structural and molar mass characteristics. Therefore, they can be used for the production of high-quality PUFs without having to adapt the synthesis process. The flexible PUFs made from recovered polyols have comparable mechanical properties to those made from virgin polyols.

Determination of End-Group Functionality of Propylene Oxide-Based Polyether Polyols Recovered from Polyurethane Foams by Chemical Recycling.

Chemical recycling of polyurethane foams (PUFs) leads to partially aromatic, amino-functionalized polyol chains when the urethane groups in the PUF structure are incompletely degraded. Since the reactivity of amino and hydroxyl groups with isocyanate groups is significantly different, information on the type of the end-group functionality of recycled polyols is important to adjust the catalyst system accordingly to produce PUFs from recycled polyols of suitable quality. Therefore, we present here a liquid adsorption chromatography (LAC) method using a SHARC 1 column that separates polyol chains according to their end-group functionality based on their ability to form hydrogen bonds with the stationary phase. To correlate end-group functionality of recycled polyol with chain size, LAC was coupled with size-exclusion chromatography (SEC) to form a two-dimensional liquid chromatography system. For accurate identification of peaks in LAC chromatograms, the results were correlated with those obtained by characterization of recycled polyols using nuclear magnetic resonance, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, and SEC coupled with a multi-detection system. The developed method allows the quantification of fully hydroxyl-functionalized chains in recycled polyols using an evaporative light scattering detector and appropriate calibration curve.

Influence of Microstructure on the Elution Behavior of Gradient Copolymers in Different Modes of Liquid Interaction Chromatography.

We studied the influence of microstructure on the chromatographic behavior of gradient copolymers with different gradient strengths and block copolymer with completely segregated blocks by using gradient liquid adsorption chromatography (gLAC) and liquid chromatography at critical conditions (LCCC) for one of the copolymer constituents. The copolymers consist of repeating units of poly(propylene oxide) and poly(propylene phthalate) and have comparable average chemical composition and molar mass, and a narrow molar mass distribution to avoid as much as possible the influence of these parameters on the elution behavior of the copolymers. On both reversed stationary phases, the elution volume of gradient copolymers increases with the increasing strength of the gradient. The results indicate that for both modes of liquid interaction chromatography, it is important to consider the effect of microstructure on the elution behavior of the gradient copolymers in addition to the copolymer chemical composition and molar mass in the case of gLAC and the length of the chromatographically visible copolymer constituent in the case of LCCC.

Influence of Low Molecular Weight Salts on the Viscosity of Aqueous-Buffer Bovine Serum Albumin Solutions.

Pharmaceutical design of protein formulations aims at maximum efficiency (protein concentration) and minimum viscosity. Therefore, it is important to know the nature of protein-protein interactions and their influence on viscosity. In this work, we investigated the dependence of the viscosity of BSA in an aqueous 20 mM acetate buffer at pH = 4.3 on protein concentration and on temperature (5-45 °C). The viscosity of the solution increased with protein concentration and was 230% higher than the viscosity of the protein-free formulation at 160 mg/mL. The viscosity decreased by almost 60% in the temperature range from 5 to 45 °C. The agreement of the modified Arrhenius theory with experiment was quantitative, whereas a hard-sphere model provided only a qualitative description of the experimental results. We also investigated the viscosity of a 100 mg/mL BSA solution as a function of the concentration of added low molecular weight salts (LiCl, NaCl, KCl, RbCl, CsCl, NaBr, NaI) in the range of salt concentrations up to 1.75 mol/L. In addition, the particle size and zeta potential of BSA-salt mixtures were determined for solutions containing 0.5 mol/L salt. The trends with respect to the different anions followed a direct Hofmeister series (Cl- > Br- > I-), whereas for cations in the case of viscosity the indirect Hofmeister series was observed (Li+ > Na+ > K+ > Rb+ > Cs+), but the values of particle sizes and zeta potential did not show cation-specific effects. Since the protein is positively charged at pH = 4.3, anions are more attracted to the protein surface and shield its charge, while the interaction with cations is less pronounced. We hypothesize that salt surface charge shielding reduces protein colloidal stability and promotes protein aggregate formation.