RESUMO
Graphene has tremendous potential in future electronics due to its superior force, electrical, and thermal properties. However, the development of graphene devices is limited by its complex, high-cost, and low-efficiency preparation process. This study proposes a novel laser bidirectional graphene printing (LBGP) process for the large-scale preparation of patterned graphene films. In LBGP, a sandwich sample composed of a thermoplastic elastomer (TPE) substrate, carbon precursor powder, and a glass cover is irradiated by a nanosecond pulsed laser. The laser photothermal effect converts the carbon precursor into graphene, with partial graphene sheets deposited directly on the TPE substrate and the remaining transferred to the glass cover via a laser-induced plasma plume. This method simultaneously prepares two face-to-face graphene films in a single laser irradiation, integrating synthesis, transfer, and patterning. The resulting graphene patterns demonstrate good performance in flexible pressure sensing and Joule heating, showcasing high sensitivity (7.7 kPa-1), fast response (37 ms), and good cycling stability (2000 cycles) for sensors, and high heating rate (1 °C s-1) and long-term stability (3000 s) for heaters. It is believed that the simple, low-cost, and efficient LBGP process can promote the development of graphene electronics and laser manufacturing processes.
RESUMO
Skin-like flexible pressure sensors with good sensing performance have great application potential, but their development is limited owing to the need for multistep, high-cost, and low-efficiency preparation processes. Herein, a simple, low-cost, and efficient laser-induced forming process is proposed for the first time to prepare a skin-like flexible piezoresistive sensor. In the laser-induced forming process, based on the photothermal effect of graphene and the foaming effect of glucose, a skin-like polydimethylsiloxanes (PDMS) film with porous structures and surface protrusions is obtained by using infrared laser irradiation of the glucose/graphene/PDMS prepolymer film. Further, based on the skin-like PDMS film with a graphene conductive layer, a new skin-like flexible piezoresistive sensor is obtained. Due to the stress concentration caused by the surface protrusions and the low stiffness caused by the porous structures, the flexible piezoresistive sensor realizes an ultrahigh sensitivity of 1348 kPa-1 at 0-2 kPa, a wide range of 200 kPa, a fast response/recovery time of 52 ms/35 ms, and good stability over 5000 cycles. The application of the sensor to the detection of human pulses and robot clamping force indicates its potential for health monitoring and soft robots. Furthermore, in combination with the neural network (CNN) algorithm in artificial intelligence technology, the sensor achieves 95% accuracy in speech recognition, which demonstrates its great potential for intelligent wearable electronics. Especially, the laser-induced forming process is expected to facilitate the efficient, large-scale preparation of flexible devices with multilevel structures.
Assuntos
Grafite , Percepção da Fala , Humanos , Inteligência Artificial , Raios Infravermelhos , Dimetilpolisiloxanos , GlucoseRESUMO
Preparing hybrid microstructures on flexible substrates is a crucial approach to achieving highly sensitive flexible pressure sensors. However, the preparation of hybrid microstructures on soft materials often faces complex, time-consuming, and costly problems, which hampers the advancement of highly sensitive flexible sensors. Herein, based on a 3D-printing template and a household microwave oven, a simple, green, and one-step microwave irradiation process using glucose porogen is applied to develop a flexible pressure sensor with a volcano-sponge-like porous dome structure based on porous polydimethylsiloxane (PDMS). Due to the easily deformable porous dome on the porous PDMS substrate, the flexible pressure sensor showcases exceptional sensitivity of 611.85 kPa-1 in 0-1 and 50.31 kPa-1 over a wide range of 20-80 kPa. Additionally, the sensor takes only 43 ms to respond, 123 ms to recover, and presents excellent stability (>1100 cycles). In application testing, the sensor effectively captures pulse signals, speech signals, tactile signals from a mechanical gripper, and gesture signals, demonstrating its potential applications in medical diagnosis and robotics. In conclusion, the microwave irradiation method based on template and glucose porogen provides a new way for the simple, low-cost, and green preparation of porous-surface hybrid microstructures on polymers and high-performance flexible pressure sensors.
RESUMO
Due to the advantages of high porosity, excellent conductivity, and tunable morphology, carbonized metal-organic framework (C-MOF) is expected to become an ideal material for constructing high-performance flexible pressure sensor. Herein, to achieving the suitable morphology of C-MOF for piezoresistive sensors, a rapid thermal process (RTP) was used for carbonization of NiCo-MOF, and the petal-shaped NiCo alloy nanoparticles/nanoporous carbon composites (NiCo-NPCs) were obtained. Compared with NiCo-NPCs carbonized by common thermal process (CTP), NiCo-NPCs carbonized by RTP exhibit a modified morphology with smaller particle size and larger most frequent pore diameter. Due to the modified morphology, the piezoresistive sensor with RTP-carbonized NiCo-NPCs has a high sensitivity of 62.13 kPa-1at 0-3 kPa, which is 3.46 times higher than that of the sensor with CTP-carbonized NiCo-NPCs. Meanwhile, the sensor shows an ultra-wide range of 1000 kPa, excellent cycle stability (>4000 cycles), and fast response/recovery time of 25/44 ms. Furthermore, the application of the sensor in dynamic loading test, airflow monitoring, voice recognition, and gesture detection demonstrates its great application prospects. In short, this work investigates the application of carbonized NiCo-MOFs in flexible pressure sensors, and provides a new strategy to improve the performance of piezoresistive sensors with porous carbon derived from MOFs.