Growth of Mesenchymal Stem Cells on Poly(3-Hydroxybutyrate) Scaffolds Loaded with Simvastatin.

We studied the effect of porous composite scaffolds based on poly(3-hydroxybutyrate) (PHB) loaded with simvastatin on the growth and differentiation of mesenchymal stem cells. The scaffolds have a suitable microstructure (porosity and pore size) and physicochemical properties to support the growth of mesenchymal stem cells. Scaffold loading with simvastatin suppressed cell growth and increased alkaline phosphatase activity, which can attest to their osteoinductive properties.

Poly(3-hydroxybutyrate)/poly(ethylene glycol) scaffolds with different microstructure: the effect on growth of mesenchymal stem cells.

Development of biocompatible 3D scaffolds is one of the most important challenges in tissue engineering. In this study, we developed polymer scaffolds of different design and microstructure to study cell growth in them. To obtain scaffolds of various microstructure, e.g., size of pores, we used double- and one-stage leaching methods using porogens with selected size of crystals. A composite of poly(3-hydroxybutyrate) (PHB) with poly(ethylene glycol) (PEG) (PHB/PEG) was used as polymer biomaterial for scaffolds. The morphology of scaffolds was analyzed by scanning electron microscopy; the Young modulus of scaffolds was measured by rheometry. The ability to support growth of mesenchymal stem cells (MSCs) in scaffolds was studied using the XTT assay; the phenotype of MSC was preliminarily confirmed by flow cytometry and the activity of alkaline phosphatase and expression level of CD45 marker was studied to test possible MSC osteogenic differentiation. The obtained scaffolds had different microstructure: the scaffolds with uniform pore size of about 125 µm (normal pores) and 45 µm (small pores) and scaffolds with broadly distributed pores size from about 50-100 µm. It was shown that PHB/PEG scaffolds with uniform pores of normal size did not support MSCs growth probably due to their marked spontaneous osteogenic differentiation in these scaffolds, whereas PHB/PEG scaffolds with diverse pore size promoted stem cells growth that was not accompanied by pronounced differentiation. In scaffolds with small pores (about 45 µm), the growth of MSC was the lowest and cell growth suppression was only partially related to stem cells differentiation. Thus, apparently, the broadly distributed pore size of PHB/PEG scaffolds promoted MSC growth in them, whereas uniform size of scaffold pores stimulated MSC osteogenic differentiation.

Biosynthesis of poly(3-hydroxybutyrate) copolymers by Azotobacter chroococcum 7B: A precursor feeding strategy.

A precursor feeding strategy for effective biopolymer producer strain Azotobacter chroococcum 7B was used to synthesize various poly(3-hydroxybutyrate) (PHB) copolymers. We performed experiments on biosynthesis of PHB copolymers by A. chroococcum 7B using various precursors: sucrose as the primary carbon source, various carboxylic acids and ethylene glycol (EG) derivatives [diethylene glycol (DEG), triethylene glycol (TEG), poly(ethylene glycol) (PEG) 300, PEG 400, PEG 1000] as additional carbon sources. We analyzed strain growth parameters including biomass and polymer yields as well as molecular weight and monomer composition of produced copolymers. We demonstrated that A. chroococcum 7B was able to synthesize copolymers using carboxylic acids with the length less than linear 6C, including poly(3-hydroxybutyrate-co-3-hydroxy-4-methylvalerate) (PHB-4MHV) using Y-shaped 6C 3-methylvaleric acid as precursor as well as EG-containing copolymers: PHB-DEG, PHB-TEG, PHB-PEG, and PHB-HV-PEG copolymers using short-chain PEGs (with n ≤ 9) as precursors. It was shown that use of the additional carbon sources caused inhibition of cell growth, decrease in polymer yields, fall in polymer molecular weight, decrease in 3-hydroxyvalerate content in produced PHB-HV-PEG copolymer, and change in bacterial cells morphology that were depended on the nature of the precursors (carboxylic acids or EG derivatives) and the timing of its addition to the growth medium.

Biosynthesis of poly(3-hydroxybutyrateco-3-hydroxy-4-methylvalerate) by Strain Azotobacter chroococcum 7B.

Production of novel polyhydroxyalkanoates (PHAs), biodegradable polymers for biomedical applications, and biomaterials based on them is a promising trend in modern bioengineering. We studied the ability of an effective strain-producer Azotobacter chroococcum 7B to synthesize not only poly(3-hydroxybutyrate) homopolymer (PHB) and its main copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), but also a novel copolymer, poly(3-hydroxybutyrate-co-3-hydroxy-4-methylvalerate) (PHB4MV). For the biosynthesis of PHB copolymers, we used carboxylic acids as additional carbon sources and monomer precursors in the chain of synthesized copolymers. The main parameters of these polymers' biosynthesis were determined: strain-producer biomass yield, polymer yield, molecular weight and monomer composition of the synthesized polymers, as well as the morphology of A. chroococcum 7B bacterial cells. The physico-chemical properties of the polymers were studied using nuclear magnetic resonance spectroscopy (NMR), differential scanning calorimetry (DSC), contact angle test, and other methods. In vitro biocompatibility of the obtained polymers was investigated using stromal cells isolated from the bone marrow of rats with the XTT cell viability test. The synthesis of the novel copolymer PHB4MV and its chemical composition were demonstrated by NMR spectroscopy: the addition of 4-methylvaleric acid to the culture medium resulted in incorporation of 3-hydroxy-4-methylvalerate (3H4MV) monomers into the PHB polymer chain (0.6 mol%). Despite the low molar content of 3H4MV in the obtained copolymer, its physico-chemical properties were significantly different from those of the PHB homopolymer: it has lower crystallinity and a higher contact angle, i.e. the physico-chemical properties of the PHB4MV copolymer containing only 0.6 mol% of 3H4MV corresponded to a PHBV copolymer with a molar content ranging from 2.5% to 7.8%. In vitro biocompatibility of the obtained PHB4MV copolymer, measured in the XTT test, was not statistically different from the cell growth of PHB and PHBV polymers, which make its use possible in biomedical research and development.

[Development and preclinical studies of insulating membranes based on poly-3-hydroxybutyrate-co-3-hydroxyvalerate for guided bone regeneration].

Bone tissue damages are one of the dominant causes of temporary disability and developmental disability. Currently, there are some methods of guided bone regeneration employing different osteoplastic materials and insulation membranes used in surgery. In this study, we have developed a method of preparation of porous membranes from the biopolymer poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV), produced by a strain of Azotobacter chroococcum 7B. The biocompatibility of the porous membranes was investigated in vitro using mesenchymal stem cells (MSCs) and in vivo on laboratory animals. The cytotoxicity test showed the possibility of cell attachment on membrane and histological studies confirmed good insulating properties the material. The data obtained demonstrate the high biocompatibility and the potential application of insulating membranes based on PHBV in bone tissue engineering.

Culturing of Mouse Mesenchymal Stem Cells on Poly-3-Hydroxybutyrate Scaffolds.

We studied the possibility of long-term culturing of mouse mesenchymal stem cells on a porous scaffold made of biocompatible polymer poly-3-hydroxybutyrate. The cells remained viable for at least 2 months and passed more than 65 population doublings in culture. Culturing on the scaffold did not change surface phenotype of cells. 3D poly-3-hydroxybutyrate scaffolds are appropriate substrate for long-term culturing of mesenchymal stem cells.

[Biocompatibility of electrospun poly(3-hydroxybutyrate) and its composites scaffolds for tissue engineering].

Development of biodegradable polymers-based scaffolds for tissue engineering is a promising trend in bioengineering. The electrospun scaffolds from poly(3-hydroxybutyrate) (PHB) were produced using different additives that changed the physical and chemical characteristics of the products. As a result, the construct consisting of interwoven threads of different diameter (0.8-3.4 mm) were obtained, the smallest diameter was observed in the threads from the PHB using tetrabutilammonium iodide (TBAI) and titanium oxide II (TiO2) as additives. Mesenchymal stem cells (MSC) were cultivated on the scaffolds for the biocompatibility evaluation of obtained materials. Cells viability was determined by the XTT assay test. It was shown that the scaffold from the interwoven threads of lowest diameter is most favorable for MSC growth in comparison with the polymer film and scaffolds from the threads of larger diameter. Thus, it was shown that the biocompatibility of electrospun PHB scaffolds depended on their microstructure. The obtained data can be used for development of scaffolds for tissue engineering.

[The effect of poly(3-hydroxybutyrate) modification by poly(ethylene glycol) on the viability of cells grown on the polymer films].

A biodegradable polymer of bacterial origin, poly(3-hydroxybutyrate) (PHB), is intensively studied as biomaterial for tissue engineering. However, factors determining its biocompatibility still require better understanding. To analyze the PHB films biocompatibility, the polymer material was modified by hydrophilic polymer, poly(ethylene glycol) 300 (PEG). The blends PHB/PEG with different PEG content (10, 20, 30 and 50%) were produced by subsequent incubation in water resulted in removal of 95% PEG. The surface roughness and hydrophilicity were studied by atomic force microscopy (AFM) and contact angle "water-polymer" measurement, respectively. The film biocompatibility on cell culture of COS-1 fibroblasts was studied in vitro. It was shown that both roughness and hydrophobicity are directly proportional to initial PEG content in the PHB/PEG blends. The growth rate of COS-1 fibroblasts on polymer films is determined by combination of two basic physicochemical properties of the polymer surface: the roughness and hydrophilicity. The optimal roughness requred for COS-1 cells growth is the average roughness more than 25 nm, whereas the limit values of the contact angle "water-polymer" that was responsible for relatively high cell viability were not found. These data indicate that the film surface roughness had the greatest effect on the cell growth, whereas the increase in the polymer surface hydrophilicity caused the additional positive effect on viability of attached cells. Thus, the modification of PHB polymer material by PEG resulted in the improved viability of cells cultivated on the polymer films in vitro. The obtained data can be used for development of such medical devices as surgeon patches and periodontal membranes.