Honeybee comb-inspired stiffness gradient-amplified catapult for solid particle repellency.

Natural surfaces that repel foreign matter are ubiquitous and crucial for living organisms. Despite remarkable liquid repellency driven by surface energy in many organisms, repelling tiny solid particles from surfaces is rare. The main challenge lies in the unfavourable scaling of inertia versus adhesion in the microscale and the inability of solids to release surface energy. Here we report a previously unexplored solid repellency on a honeybee's comb: a catapult-like effect to immediately eject pollen after grooming dirty antennae for self-cleaning. Nanoindentation tests revealed the 38-µm-long comb features a stiffness gradient spanning nearly two orders of magnitude from ~25 MPa at the tip to ~645 MPa at the base. This significantly augments the elastic energy storage and accelerates the subsequent conversion into kinetic energy. The reinforcement in energy storage and conversion allows the particle's otherwise weak inertia to outweigh its adhesion, thereby suppressing the unfavourable scaling effect and realizing solid repellency that is impossible in conventional uniform designs. We capitalize on this to build an elastomeric bioinspired stiffness-gradient catapult and demonstrate its generality and practicality. Our findings advance the fundamental understanding of natural catapult phenomena with the potential to develop bioinspired stiffness-gradient materials, catapult-based actuators and robotic cleaners.

Self-Adaptive Droplet Bouncing on a Dual Gradient Surface.

Rapid detachment of impacting droplets from underlying substrate is highly preferred for mass, momentum, and energy exchange in many practical applications. Driven by this, the past several years have witnessed a surge in engineering macrotexture to reduce solid-liquid contact time. Despite these advances, these strategies in reducing contact time necessitate the elegant control of either the spatial location for droplet contact or the range of impacting velocity. Here, this work circumvents these limitations by designing a dual gradient surface consisting of a vertical spacing gradient made of tapered pillar arrays and a lateral curvature gradient characterized as macroscopic convex. This design enables the impacting droplets to self-adapt to asymmetric or pancake bouncing mode accordingly, which renders significant contact time reduction (up to ≈70%) for a broad range of impacting velocities (≈0.4-1.4 m s-1 ) irrespective of the spatial impacting location. This new design provides a new insight for designing liquid-repellent surfaces, and offers opportunities for applications including dropwise condensation, energy conversion, and anti-icing.

Achieving ultra-stable and superior electricity generation by integrating transistor-like design with lubricant armor.

Extensive work have been done to harvest untapped water energy in formats of raindrops, flows, waves, and others. However, attaining stable and efficient electricity generation from these low-frequency water kinetic energies at both individual device and large-scale system level remains challenging, partially owing to the difficulty in designing a unit that possesses stable liquid and charge transfer properties, and also can be seamlessly integrated to achieve preferential collective performances without the introduction of tortuous wiring and redundant node connection with external circuit. Here, we report the design of water electricity generators featuring the combination of lubricant layer and transistor-like electrode architecture that endows enhanced electrical performances in different working environments. Such a design is scalable in manufacturing and suitable for facile integration, characterized by significant reduction in the numbers of wiring and nodes and elimination of complex interfacing problems, and represents a significant step toward large-scale, real-life applications.

Electrically switched underwater capillary adhesion.

Developing underwater adhesives that can rapidly and reversibly switch the adhesion in wet conditions is important in various industrial and biomedical applications. Despite extensive progresses, the manifestation of underwater adhesion with rapid reversibility remains a big challenge. Here, we report a simple strategy that achieves strong underwater adhesion between two surfaces as well as rapid and reversible detachment in on-demand manner. Our approach leverages on the design of patterned hybrid wettability on surfaces that selectively creates a spatially confined integral air shell to preserve the water bridge in underwater environment. The overall adhesion strength can be multiplied by introducing multiple air shells and rapidly broken by disturbing the integrity of the protective air shell in response to the applied voltage on two surfaces. Our design can be constructed on the flexible substrate with hybrid wettability, which can be applied to non-conductive substrates and adapted to more complicated morphologies, extending the choice of underlying materials.

Bubble energy generator.

Bubbles have been extensively explored as energy carriers ranging from boiling heat transfer and targeted cancer diagnosis. Yet, despite notable progress, the kinetic energy inherent in small bubbles remains difficult to harvest. Here, we develop a transistor-inspired bubble energy generator for directly and efficiently harvesting energy from small bubbles. The key points lie in designing dielectric surface with high-density electric charges and tailored surface wettability as well as transistor-inspired electrode configuration. The synergy between these features facilitates fast bubble spreading and subsequent departure, transforms the initial liquid/solid interface into gas/solid interface under the gating of bubble, and yields an output at least one order of magnitude higher than existing studies. We also show that the output can be further enhanced through rapid bubble collapse at the air/liquid interface and multiple bubbles synchronization. We envision that our design will pave the way for small bubble-based energy harvesting in liquid media.

3D Printed, Solid-State Conductive Ionoelastomer as a Generic Building Block for Tactile Applications.

Shaping soft and conductive materials into preferential architectures via 3D printing is highly attractive for numerous applications ranging from tactile devices to bioelectronics. A landmark type of soft and conductive materials is hydrogels/ionogels. However, 3D-printed hydrogels/ionogels still suffer from a fundamental bottleneck: limited stability in their electrical-mechanical properties caused by the evaporation and leakage of liquid within hydrogels/ionogels. Although photocurable liquid-free ion-conducting elastomers can circumvent these limitations, the associated photocurable process is cumbersome and hence the printing quality is relatively poor. Herein, a fast photocurable, solid-state conductive ionoelastomer (SCIE) is developed that enables high-resolution 3D printing of arbitrary architectures. The printed building blocks possess many promising features over the conventional ion-conducting materials, including high resolution architectures (even ≈50 µm overhanging lattices), good Young's modulus (up to ≈6.2 MPa), and stretchability (fracture strain of ≈292%), excellent conductivity tolerance in a wide range of temperatures (from -30 to 80 °C), as well as fine elasticity and antifatigue ability even after 10 000 loading-unloading cycles. It is further demonstrated that the printed building blocks can be programmed into 3D flexible tactile sensors such as gyroid-based piezoresistive sensor and gap-based capacitive sensor, both of which exhibit several times higher in sensitivity than their bulky counterparts.

Three-dimensional capillary ratchet-induced liquid directional steering.

Conventional understanding has it that a liquid deposited on a surface tends to move along directions that reduce surface energy, which is mainly dictated by surface properties rather than liquid properties, such as surface tension. Achieving well-controlled directional steering remains challenging because the liquid-solid interaction mainly occurs in the two-dimensional (2D) domain. We show that the spreading direction of liquids with different surface tensions can be tailored by designing 3D capillary ratchets that create an asymmetric and 3D spreading profile both in and out of the surface plane. Such directional steering is also accompanied by self-propulsion and high flow velocity, all of which are preferred in liquid transport.

Explosive Pancake Bouncing on Hot Superhydrophilic Surfaces.

The rapid detachment of liquid droplets from engineered surfaces in the form of complete rebound, pancake bouncing, or trampolining has been extensively studied over the past decade and is of practical importance in many industrial processes such as self-cleaning, anti-icing, energy conversion, and so on. The spontaneous trampolining of droplets needs an additional low-pressure environment and the manifestation of pancake bouncing on superhydrophobic surfaces requires meticulous control of macrotextures and impacting velocity. In this work, we report that the rapid pancake-like levitation of impinging droplets can be achieved on superhydrophilic surfaces through the application of heating. In particular, we discovered explosive pancake bouncing on hot superhydrophilic surfaces made of hierarchically non-interconnected honeycombs, which is in striking contrast to the partial levitation of droplets on the surface consisting of interconnected microposts. This enhanced droplet bouncing phenomenon, characterized by a significant reduction in contact time and increase in the bouncing height, is ascribed to the production and spatial confinement of pressurized vapor in non-interconnected structures. The manifestation of pancake bouncing on the superhydrophilic surface rendered by a bottom-to-up boiling process may find promising applications such as the removal of trapped solid particles.

Directional Liquid Transport from the Cold Region to the Hot Region on a Topological Surface.

Manifested from the "tears of wine" to the "coffee-ring effect", the directional transport of a liquid governed by the Marangoni effect is highly pervasive in our daily life and has brought a great number of applications. Similar to this surface tension gradient-dominated process, the fluid preferentially flows from the hot region to the cold region. In contrast to this perception, in this study, we report that water liquid deposited on a specially designed topological surface can flow from the low-temperature region to the high-temperature region in a spontaneous, long-range, and unidirectional manner. We show that such a behavior is mainly owing to a strong topological effect that outweighs the thermal gradient imposed along the surface. Moreover, the specific temperature range applied on the topological surface for the occurrence of such a unidirectional liquid transport phenomenon is also identified. Our findings would find important insights for developing next-generation cooling devices where a rapid flow from the condensation region to the evaporation/boiling region is preferred.

Dopamine-Triggered Hydrogels with High Transparency, Self-Adhesion, and Thermoresponse as Skinlike Sensors.

Mussel-inspired conductive hydrogels are attractive for the development of next-generation self-adhesive, flexible skinlike sensors. However, despite extensive progress, there are still some daunting challenges that hinder their applications, such as inferior optical transparency, low catechol content (e.g., poor adhesion), as well as limited sensation performances. Here, we report a dopamine-triggered gelation (DTG) strategy for fabricating mussel-inspired, transparent, and conductive hydrogels. The DTG design leverages on the dual functions of dopamine, which serves as both polymerization initiator and dynamic mediator to elaborate and orchestrate the cross-linking networks of hydrogels, allowing for pronounced adhesion, robust elasticity, self-healing ability, excellent injectability and three-dimensional printability, reversible and tunable transparent-opaque transition, and thermoresponsive feature. These preferable performances enable DTG hydrogels as self-adhesive, flexible skinlike sensors for achieving multiple sensations toward pressure, strain, and temperature, even an extraordinary visual perception effect, making it a step closer in the exploration of future biomimetic skin.

Electronic Skin from High-Throughput Fabrication of Intrinsically Stretchable Lead Zirconate Titanate Elastomer.

Electronic skin made of thin, soft, stretchable devices that can mimic the human skin and reconstruct the tactile sensation and perception offers great opportunities for prosthesis sensing, robotics controlling, and human-machine interfaces. Advanced materials and mechanics engineering of thin film devices has proven to be an efficient route to enable and enhance flexibility and stretchability of various electronic skins; however, the density of devices is still low owing to the limitation in existing fabrication techniques. Here, we report a high-throughput one-step process to fabricate large tactile sensing arrays with a sensor density of 25 sensors/cm2 for electronic skin, where the sensors are based on intrinsically stretchable piezoelectric lead zirconate titanate (PZT) elastomer. The PZT elastomer sensor arrays with great uniformity and passive-driven manner enable high-resolution tactile sensing, simplify the data acquisition process, and lower the manufacturing cost. The high-throughput fabrication process provides a general platform for integrating intrinsically stretchable materials into large area, high device density soft electronics for the next-generation electronic skin.

Tip-induced flipping of droplets on Janus pillars: From local reconfiguration to global transport.

Despite their simplicity, water droplets manifest a wide spectrum of forms and dynamics, which can be actuated using special texture at solid surfaces to achieve desired functions. Along this vein, natural or synthetic materials can be rendered water repellent, oleophobic, antifogging, anisotropic, etc.-all properties arising from an original design of the substrate and/or from the use of special materials promoting capillary or elastic forces at the droplet scale. Here, we report an original phenomenon occurring at the tip of asymmetric (half-flat, half-curved) pillars: Droplets reconfigure and get oriented on the curved side of these Janus tips. This local, geometry-driven effect, namely, tip-induced flipping of droplets, is found to be generic and have spectacular global consequences: Vast assemblies of Janus pillars enable a continuous, long-range, and fast self-transport of water harvested from fogs, which makes it possible to collect and concentrate droplets at different scales.

A droplet-based electricity generator with high instantaneous power density.

Extensive efforts have been made to harvest energy from water in the form of raindrops1-6, river and ocean waves7,8, tides9 and others10-17. However, achieving a high density of electrical power generation is challenging. Traditional hydraulic power generation mainly uses electromagnetic generators that are heavy, bulky, and become inefficient with low water supply. An alternative, the water-droplet/solid-based triboelectric nanogenerator, has so far generated peak power densities of less than one watt per square metre, owing to the limitations imposed by interfacial effects-as seen in characterizations of the charge generation and transfer that occur at solid-liquid1-4 or liquid-liquid5,18 interfaces. Here we develop a device to harvest energy from impinging water droplets by using an architecture that comprises a polytetrafluoroethylene film on an indium tin oxide substrate plus an aluminium electrode. We show that spreading of an impinged water droplet on the device bridges the originally disconnected components into a closed-loop electrical system, transforming the conventional interfacial effect into a bulk effect, and so enhancing the instantaneous power density by several orders of magnitude over equivalent devices that are limited by interfacial effects.

Crack engineering for the construction of arbitrary hierarchical architectures.

Three-dimensional hierarchical morphologies widely exist in natural and biomimetic materials, which impart preferential functions including liquid and mass transport, energy conversion, and signal transmission for various applications. While notable progress has been made in the design and manufacturing of various hierarchical materials, the state-of-the-art approaches suffer from limited materials selection, high costs, as well as low processing throughput. Herein, by harnessing the configurable elastic crack engineering-controlled formation and configuration of cracks in elastic materials-an effect normally avoided in various industrial processes, we report the development of a facile and powerful technique that enables the faithful transfer of arbitrary hierarchical structures with broad material compatibility and structural and functional integrity. Our work paves the way for the cost-effective, large-scale production of a variety of flexible, inexpensive, and transparent 3D hierarchical and biomimetic materials.

Fabrication of Wettability Mesh with Quasi-Rectangular-Restraining Capacity to Water.

A water droplet placed on a surface is usually round owing to surface tension. Restraining a droplet to a rectangle shape has been rarely reported. Herein, we fabricated three meshes with diverse wettability including ordinary mesh, superhydropilic mesh, and quasi-rectangular-restraining mesh. The profiles of water droplets on these three meshes were entirely different from the top view, especially for the quasi-rectangular-restraining mesh, which enables the water droplet on it to achieve the rectangular shape. The surface morphologies and chemical compositions of the meshes were characterized by scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction. Moreover, the influences of processing parameters of the quasi-rectangular-restraining mesh on the quasi-rectangular quality of the water droplet on it were investigated to obtain the relatively optimum processing parameters. The dynamic properties of water droplets on the three meshes were compared, and forces acting on the water droplets during the spreading and shrinking processes on the three meshes were qualitatively analyzed. Additionally, we studied the influences of falling height and water volume on the quasi-rectangular quality of the water droplet on the quasi-rectangular-restraining mesh. Water droplets on the quasi-rectangular-restraining mesh demonstrated good stability under vibration and the droplet could maintain the quasi-rectangular quality on the quasi-rectangular-restraining mesh for about 7 days, revealing a good durability. Further, the large-scaled fabrication of the quasi-rectangular-restraining mesh was realized.

Designing biomimetic liquid diodes.

Just as the innovation of electronic diodes that allow the current to flow in one direction provides a foundation for the development of digital technologies, the engineering of surfaces or devices that allow the directional and spontaneous transport of fluids, termed liquid diodes, is highly desired in a wide spectrum of applications ranging from medical microfluidics, advanced printing, heat management and water collection to oil-water separation. Recent advances in manufacturing, visualization techniques, and biomimetics have led to exciting progress in the design of various liquid diodes. In spite of exciting progress, formulating a general framework broad enough to guide the design, optimization and fabrication of engineered liquid diodes remains a challenging task to date. In this review, we first present an overview of the development of biological and engineered liquid diodes to elucidate how to control the surface chemistry and topography to regulate the transport of liquids without the need for external energy. Then the latest design strategies allowing for the creation of longitudinal and transverse liquid diodes are discussed and compared. We also define some figures of merit such as the rectification coefficient and the transport velocity and distance to quantify the performance of liquid diodes. Finally, we highlight perspectives on the development of engineered liquid diodes that transcend nature and adapt to various practical applications.

SLIPS-TENG: robust triboelectric nanogenerator with optical and charge transparency using a slippery interface.

Energy harvesting devices that prosper in harsh environments are highly demanded in a wide range of applications ranging from wearable and biomedical devices to self-powered and intelligent systems. Particularly, over the past several years, the innovation of triboelectric nanogenerators (TENGs) that efficiently convert ambient kinetic energy of water droplets or wave power to electricity has received growing attention. One of the main bottlenecks for the practical implications of such devices originates from the fast degradation of the physiochemical properties of interfacial materials under harsh environments. To overcome these challenges, here we report the design of a novel slippery lubricant-impregnated porous surface (SLIPS) based TENG, referred to as SLIPS-TENG, which exhibits many distinctive advantages over conventional design including optical transparency, configurability, self-cleaning, flexibility, and power generation stability, in a wide range of working environments. Unexpectedly, the slippery and configurable lubricant layer not only serves as a unique substrate for liquid/droplet transport and optical transmission, but also for efficient charge transfer. Moreover, we show that there exists a critical thickness in the liquid layer, below which the triboelectric effect is almost identical to that without the presence of such a liquid film. Such an intriguing charge transparency behavior is reminiscent of the wetting transparency and van der Waals potential transparency of graphene previously reported, though the fundamental mechanism remains to be elucidated. We envision that the marriage of these two seemingly totally different arenas (SLIPS and TENG) provides a paradigm shift in the design of robust and versatile energy devices that can be used as a clean and longer-lifetime alternative in various working environments.

Maskless Hydrophilic Patterning of the Superhydrophobic Aluminum Surface by an Atmospheric Pressure Microplasma Jet for Water Adhesion Controlling.

Superhydrophobic surfaces with hydrophilic patterns have great application potential in various fields, such as microfluidic systems and water harvesting. However, many reported preparation methods involve complicated devices and/or masks, making fabrication of these patterned surfaces time-consuming and inefficient. Here, we propose a highly efficient, simple, and maskless microplasma jet (MPJ) treatment method to prepare hydrophilic patterns such as dots, lines, and curves on superhydrophobic aluminum substrates. Contact angles, sliding angles, adhesive forces, and droplet impact behavior of the created patterns are investigated and analyzed. The prepared "dot" patterns exhibit great water adhesion, whereas the "line" patterns show anisotropic adhesion. Additionally, the MPJ treatment does not obviously change the surface structures, which makes it possible to achieve repeatable patterning on one substrate. The adhesion behavior of these patterns could be adjusted using MPJs with different diameters. MPJs with larger diameters are efficient for the creation of patterns with high water adhesion, which can be potentially used for open-channel lab-on-chip systems (e.g., continuous water transportation), whereas MPJs with smaller diameters are preferable in preparing patterns with low water adhesion for diverse applications in biomedical fields (e.g., lossless liquid droplet mixing and cell screening).

Anisotropic sliding on dual-rail hydrophilic tracks.

Biomimetic surfaces with sliding angle (SA) anisotropy have the capacity to directionally control the motion of water droplets and therefore have wide applications in various domains. Parallel and narrowing dual-rail hydrophilic tracks (DRHTs) are fabricated on etched superhydrophobic Al surfaces using a micromilling technique. Orthogonal and linear SA anisotropies are observed and investigated on the parallel and narrowing DRHTs, respectively. Track spacings of the parallel DRHTs are designed to regulate the orthogonal SA anisotropy of the water droplet. Experimental data shows that the along-track droplet-substrate interfacial widths, together with the sliding anisotropy, decrease with the increase of the track spacings. SA contrast (linear SA anisotropy) in two opposite directions along the tracks is observed and discussed on the narrowing DRHTs. Results indicate that droplets slide with more difficulty in the spacing-expanding direction than those in the shrinking direction, and when a droplet is dispensed at the tail end of a DRHT segment, the along-track outward detaching SAs and inward SAs also show sharp linear anisotropy due to the droplet-track interfacial liquid tension. On the basis of the discussed orthogonal and linear SAs, potential lab-on-a-chip applications for intelligent droplet transport, mixing and capture & release are explored.

Underwater Spontaneous Pumpless Transportation of Nonpolar Organic Liquids on Extreme Wettability Patterns.

Spontaneous pumpless transportation (SPT) of liquids has generated tremendous demands in microfluidic systems and advanced devices. However, the transportation of nonpolar organic liquids on open platforms underwater remains a challenge because most existing SPT systems are only designed for use in air. Here, we report a surface-tension-driven SPT system to transport various nonpolar organic liquids using underwater extreme wettability patterns. The patterns were fabricated with a wedge-shaped superoleophilic track on a superoleophobic background by combining CuCl2 etching, stearic acid modification, and mask-based nitrogen cold plasma treatment. Three types of underwater SPT processes-horizontal transport, tilted transport, and directional transport-were studied experimentally and theoretically. For horizontal SPT and tilted SPT, the capillary force was the main driving force, which depended on the wedge angle of the superoleophilic track. The excellent transportation ability of horizontal SPT of underwater liquid droplets was obtained at a wedge angle of 3-5°. The maximum moving height of organic liquids on the tilted SPT transport was obtained at an angle of 8°. For directional SPT, organic liquids did not drop off in the moving process because of the constraint imposed by surface tension, resulting in the sustained directional transport with long distances and complex trajectories.