RESUMO
Natural compound eyes inspire the development of artificial optical devices that feature a large field of view and fast motion detection. However, the imaging of artificial compound eyes dramatically depends on many microlenses. The single focal length of the microlens array significantly limits the actual applications of artificial optical devices, like distinguishing objects at different distances. In this study, a curved artificial compound eye for a microlens array with different focal lengths was fabricated by inkjet printing and air-assisted deformation. By adjusting the space of the microlens array, secondary microlenses were created between intervals of the primary microlens. The diameter/height of the primary and secondary microlens arrays are 75/25 µm and 30/9 µm, respectively. The planar-distributed microlens array was transformed into a curved configuration using air-assisted deformation. Compared with adjusting the curved base to distinguish objects at different distances, the reported technique features simplicity and is easy to operate. The applied air pressure can be used to tune the field of view of the artificial compound eye. The microlens arrays with different focal lengths could distinguish the objects at different distances without additional components. When the external objects move a small distance, they can be detected by the microlens arrays due to their different focal lengths. It could effectively improve the motion perception of the optical system. Moreover, the focusing and imaging performances of the fabricated artificial compound eye were further tested. The compound eye combines the advantages of monocular eyes and compound eyes, holding great potential for developing advanced optical devices with a large field of view and automatic variable-focus imaging.
RESUMO
Microlens arrays (MLAs) are the key components of miniaturized optical systems. To meet the stringent requirements for their application in humid environments, achieving waterproof properties in these objects is an urgent task. It is noteworthy that conventional methods of microlens production usually sacrifice optical performance for stable superhydrophobicity by increasing the surface roughness of the microlens. In this paper, a large area artificial compound eye (ACE) is efficiently fabricated by combining photolithography and inkjet printing. The added micropillars separated the outside droplet from the microlens, and the water droplet was afterward suspended on the top of micropillars. Furthermore, the micropillars enabled superhydrophobicity (at a contact angle above 150°) and low surface adhesion (at a sliding angle of â¼2.8°) of the microlens without affecting its optical performance. Furthermore, when released from the height of 1 and 2 cm, the droplets were fully detached from the surface without sticking. The surface of the ACE was shown to have relatively stable nonwettability due to a small spacing between the micropillars. This means that tuning the morphology and spacing between micropillars allows one to noticeably improve the surface nonwettability stability. Finally, the performance of the fabricated optical system was demonstrated in a water washing experiment. Therefore, the findings of present study may open up the prospects for significant advancement in superhydrophobicity of the optical systems without affecting their imaging performance for real outdoor applications.
RESUMO
Natural compound eyes have inspired the development of self-cleaning, waterproof, and antifog optical devices. However, the traditional methods generally sacrifice the transparency of optical units to introduce hydrophobicity, which significantly limits the practical applications of state-of-the-art hydrophobic technologies. This work aims to fabricate a microimaging system by combining photolithography, inkjet printing, and chemical growth. Herein, an artificial compound eye (ACE) is endowed with stable superhydrophobicity and high transparency without affecting its optical performance. The obtained ACE system possesses good static and dynamic dewetting properties along with excellent optical performance. Its static contact angle exceeds 160°, whereas the sliding angle and contact angle hysteresis values are â¼5.5° and â¼3.8°, respectively. Furthermore, the contact time is found to be 11.97 s for the Weber number of 12. The droplet undergoes a reversible process during compressing and stretching, and the ACE exhibits no adhesion under a pressure load of 4 mN. This proves that the introduction of nonwetting nanohairs on the sidewalls of the microcone arrays significantly improves the dynamic dewetting of the system. More importantly, the properly designed position of nanohairs ensures that the optical performance of ACE is maintained at a level of â¼95% compared to that of the bare glass. The superhydrophobic ACE exhibits low adhesion and great transparency. This rationally designed ACE may provide useful guidelines for fabrication of superhydrophobic optical devices with high transparency and enable potential applications in military, medical, and some outdoor activity fields.
RESUMO
A 9-year field experiment was conducted on the Guanzhong Plain of Shaanxi Province to study the effects of subsoiling, rotary tillage, straw return, no-till seeding, and traditional tillage on the soil physical and chemical properties and the grain yield in a winter wheat-summer maize rotation system, and a comprehensive evaluation was made on the soil quality under these tillage patterns by the method of principal components analysis (PCA). Comparing with traditional tillage, all the conservation tillage patterns improved soil fertility quality and soil physical properties. Under conservative tillage, the activities of soil urease and alkaline phosphatase increased significantly, soil quality index increased by 19.8%-44.0%, and the grain yield of winter wheat and summer maize (expect that under no till seeding with straw covering) increased by 13%-28% and 3%-12%, respectively. Subsoiling every other year, straw-chopping combined with rotary tillage, and straw-mulching combined with subsoiling not only increased crop yield, but also improved soil quality. Based on the economic and ecological benefits, the practices of subsoiling and straw return should be promoted.