In-operando FTIR study of ligand-linked Pt nanoparticle networks employed as catalysts in hydrogen gas micro sensors.

Microporous networks of Pt nanoparticles (NP) interlinked by aromatic diamines have recently shown prospects of application as hydrogen combustion catalysts in H2 gas microsensors. In particular with respect to long-term sensor performance, they outperformed plain Pt NP as catalysts. In this paper, electron microscopy and Fourier transform infrared (FTIR) spectroscopy data on the stability of p-phenylene diamine (PDA) and of the PDA-linked Pt NP network structure during catalyst activation and long-term sensor operation at elevated temperature (up to 120-180 °C) will be presented. For the first time, all data were collected directly from microsensor catalysts, and FTIR was performed in operando, i.e., during activation and sensor operation. While the data confirm high long-term catalyst activity far superior to that of plain Pt NP over 5 days of testing, they reveal that PDA fully decomposed during long-term sensor operation and that the network of discrete Pt nanoparticles changed to a sponge-like Pt nanostructure already during catalyst activation. These findings are at variance with previous work which assumed that stability of the PDA-linked Pt NP network is prerequisite for catalyst stability and performance.

Synthesis and Characterization of Ligand-Linked Pt Nanoparticles: Tunable, Three-Dimensional, Porous Networks for Catalytic Hydrogen Sensing.

Porous networks of Pt nanoparticles interlinked by bifunctional organic ligands have shown high potential as catalysts in micro-machined hydrogen gas sensors. By varying the ligand among p-phenylenediamine, benzidine, 4,4''-diamino-p-terphenyl, 1,5-diaminonaphthalene, and trans-1,4-diaminocyclohexane, new variants of such networks were synthesized. Inter-particle distances within the networks, determined via transmission electron microscopy tomography, varied from 0.8 to 1.4 nm in accordance with the nominal length of the respective ligand. While stable structures with intact and coordinatively bonded diamines were formed with all ligands, aromatic diamines showed superior thermal stability. The networks exhibited mesoporous structures depending on ligand and synthesis strategy and performed well as catalysts in hydrogen gas microsensors. They demonstrate the possibility of deliberately tuning micro- and mesoporosity and thereby transport properties and steric demands by choice of the right ligand also for other applications in heterogeneous catalysis.

Design and Fabrication Challenges of a Highly Sensitive Thermoelectric-Based Hydrogen Gas Sensor.

This paper presents a highly sensitive thermoelectric sensor for catalytic combustible gas detection. The sensor contains two low-stress (+176 MPa) membranes of a combination of stoichiometric and silicon-rich silicon nitride that makes them chemically and thermally stable. The complete fabrication process with details, especially the challenges and their solutions, is discussed elaborately. In addition, a comprehensive evaluation of design criteria and a comparative analysis of different sensor designs are performed with respect to the homogeneity of the temperature field on the membrane, power consumption, and thermal sensitivity. Evaluating the respective tradeoffs, the best design is selected. The selected sensor has a linear thermal characteristic with a sensitivity of 6.54 mV/K. Additionally, the temperature profile on the membrane is quite homogeneous (20% root mean standard deviation), which is important for the stability of the catalytic layer. Most importantly, the sensor with a ligand (p-Phenylenediamine (PDA))-linked platinum nanoparticles catalyst shows exceptionally high response to hydrogen gas, i.e., 752 mV at 2% concentration.

Ligand-Linked Nanoparticles-Based Hydrogen Gas Sensor with Excellent Homogeneous Temperature Field and a Comparative Stability Evaluation of Different Ligand-Linked Catalysts.

This paper presents a thermoelectric gas microsensor with improved stability where platinum nanoparticles linked by bifunctional ligands are used as a catalyst. The sensor design provides a homogeneous temperature field over the membrane, an important factor for the long-term stability of the catalyst. A comprehensive study of heat transfer from the chip is performed to evaluate the convection heat loss coefficient and to understand its effect on the homogeneity of the temperature field in a real-time situation. The effect of highly heat-conductive thermopiles is also analyzed by comparing the temperature distribution and power consumption with a thermoresistive sensor of the same dimensions and materials. Despite the thermopiles, the thermoelectric sensor gives better temperature homogeneity and consumes 23% less power than the thermoresistive sensor for 90 °C average temperature on the membrane. A comparative stability analysis among ligand-linked nanoparticles with 5 different ligands and unprotected nanoparticles was done through 3 consecutive 24 h tests under 1.5% continuous hydrogen gas flow. The sensors give very stable output, almost no degradation, through 72 h (3 × 24 h) tests for 3 different ligand-linked nanoparticles. The sensor design provides superb stability to the catalyst: Even catalysts of unprotected nanoparticles withstood more than 24 h and the sensor signal degradation is only 20%.

Influence of Water on Chemical Vapor Deposition of Ni and Co thin films from ethanol solutions of acetylacetonate precursors.

In chemical vapor deposition experiments with pulsed spray evaporation (PSE-CVD) of liquid solutions of Ni and Co acetylacetonate in ethanol as precursors, the influence of water in the feedstock on the composition and growth kinetics of deposited Ni and Co metal films was systematically studied. Varying the water concentration in the precursor solutions, beneficial as well as detrimental effects of water on the metal film growth, strongly depending on the concentration of water and the ß-diketonate in the precursor, were identified. For 2.5 mM Ni(acac)2 precursor solutions, addition of 0.5 vol% water improves growth of a metallic Ni film and reduces carbon contamination, while addition of 1.0 vol% water and more leads to significant oxidation of deposited Ni. By tuning the concentration of both, Ni(acac)2 and water in the precursor solution, the fraction of Ni metal and Ni oxide in the film or the film morphology can be adjusted. In the case of Co(acac)2, even smallest amounts of water promote complete oxidation of the deposited film. All deposited films were analyzed with respect to chemical composition quasi in situ by XPS, their morphology was evaluated after deposition by SEM.

Controlling the physics and chemistry of binary and ternary praseodymium and cerium oxide systems.

Rare earth praseodymium and cerium oxides have attracted intense research interest in the last few decades, due to their intriguing chemical and physical characteristics. An understanding of the correlation between structure and properties, in particular the surface chemistry, is urgently required for their application in microelectronics, catalysis, optics and other fields. Such an understanding is, however, hampered by the complexity of rare earth oxide materials and experimental methods for their characterisation. Here, we report recent progress in studying high-quality, single crystalline, praseodymium and cerium oxide films as well as ternary alloys grown on Si(111) substrates. Using these well-defined systems and based on a systematic multi-technique surface science approach, the corresponding physical and chemical properties, such as the surface structure, the surface morphology, the bulk-surface interaction and the oxygen storage/release capability, are explored in detail. We show that specifically the crystalline structure and the oxygen stoichiometry of the oxide thin films can be well controlled by the film preparation method. This work leads to a comprehensive understanding of the properties of rare earth oxides and highlights the applications of these versatile materials. Furthermore, methanol adsorption studies are performed on binary and ternary rare earth oxide thin films, demonstrating the feasibility of employing such systems for model catalytic studies. Specifically for ceria systems, we find considerable stability against normal environmental conditions so that they can be considered as a "materials bridge" between surface science models and real catalysts.

Influence of Sn content on the hydrogenation of crotonaldehyde catalysed by colloidally prepared PtSn nanoparticles.

Bimetallic PtSn nanoparticles (NPs) of well-defined size and metal composition were prepared by means of colloidal methods. The mean particle diameter was about 2 nm for all samples irrespective of the Pt/Sn-ratio, which enables a systematic study of the influence of the composition on the catalytic properties while excluding particle size effects. The hydrogenation of crotonaldehyde was investigated as a reaction for which chemoselectivity is known to be a challenging task. Already very low atomic Sn contents (≈10%) were found to lead to a significantly improved activity which may be attributed to an electronic effect of Sn on Pt. For further increasing tin contents the activity decreased gradually. This trend was accompanied by a steady increase in selectivity towards the desired product (crotylalcohol). The results show that the highest crotylalcohol time yields can be obtained by using catalysts with an atomic Sn content of approximately 23%. In contrast, maximum crotylalcohol selectivities are achieved by using catalysts with a high tin content (>50%).

Methanol Adsorption and Reaction on Samaria Thin Films on Pt(111).

We investigated the adsorption and reaction of methanol on continuous and discontinuous films of samarium oxide (SmOx) grown on Pt(111) in ultrahigh vacuum. The methanol decomposition was studied by temperature programmed desorption (TPD) and infrared reflection absorption spectroscopy (IRRAS), while structural changes of the oxide surface were monitored by low-energy electron diffraction (LEED). Methanol dehydrogenates to adsorbed methoxy species on both the continuous and discontinuous SmOx films, eventually leading to the desorption of CO and H2 which desorbs at temperatures in the range 400-600 K. Small quantities of CO2 are also detected mainly on as-prepared Sm2O3 thin films, but the production of CO2 is limited during repeated TPD runs. The discontinuous film exhibits the highest reactivity compared to the continuous film and the Pt(111) substrate. The reactivity of methanol on reduced and reoxidized films was also investigated, revealing how SmOx structures influence the chemical behavior. Over repeated TPD experiments, a SmOx structural/chemical equilibrium condition is found which can be approached either from oxidized or reduced films. We also observed hydrogen absence in TPD which indicates that hydrogen is stored either in SmOx films or as OH groups on the SmOx surfaces.

Design of a compact ultrahigh vacuum-compatible setup for the analysis of chemical vapor deposition processes.

Optimizing thin film deposition techniques requires contamination-free transfer from the reactor into an ultrahigh vacuum (UHV) chamber for surface science analysis. A very compact, multifunctional Chemical Vapor Deposition (CVD) reactor for direct attachment to any typical UHV system for thin film analysis was designed and built. Besides compactness, fast, easy, and at the same time ultimately clean sample transfer between reactor and UHV was a major goal. It was achieved by a combination of sample manipulation parts, sample heater, and a shutter mechanism designed to fit all into a NW38 Conflat six-ways cross. The present reactor design is versatile to be employed for all commonly employed variants of CVD, including Atomic Layer Deposition. A demonstration of the functionality of the system is provided. First results of the setup (attached to an Omicron Multiprobe x-ray photoelectron spectroscopy system) on the temperature dependence of Pulsed Spray Evaporation-CVD of Ni films from Ni acetylacetonate as the precursor demonstrate the reactor performance and illustrate the importance of clean sample transfer without breaking vacuum in order to obtain unambiguous results on the quality of CVD-grown thin Ni films. The widely applicable design holds promise for future systematic studies of the fundamental processes during chemical vapor deposition or atomic layer deposition.

Ethylene diamine-assisted synthesis of iron oxide nanoparticles in high-boiling polyolys.

The decomposition of iron(III) acetylacetonate in high-boiling polyols such as diethylene glycole is an efficient way to produce water-soluble iron oxide nanoparticles (IONPs) with small sizes. We present an extension of this method by introducing ethylene diamine (EDA) or diethylene triamine (DTA) as a structure-directing agent and adding polyvinylpyrrolidone (PVP) as a stabilizing agent. The synthesis was studied with respect to effects of the chain length of the polyol used as solvent, the chain length of the structure-directing agent, the presence of PVP, the heating rate, and the nature of the precursor. By varying these parameters, we were able to show, that probably an interplay of the structure-directing agent and the polyol plays an important role for the stabilization and growth of the different facets of the IONP crystal. The chain length of the polyol used as solvent alters the influence of EDA or DTA as stabilizer of {111} facets, leading to IONPs with spherical, tetrahedral, or nanoplate morphology and mean diameters ranging from 4 nm up to 25 nm. PVP in the reaction medium narrows down particle size and shape distributions and promotes the formation of very stable, water-based colloidal solutions. The saturation magnetization of the particles was determined by a superconducting quantum interference device (SQUID) and their ability to act as a T2-contrast agent was tested by magnetic resonance imaging (MRI).

Colloidal synthesis and structural control of PtSn bimetallic nanoparticles.

PtSn bimetallic nanoparticles with different particle sizes (1-9 nm), metal compositions (Sn content of 10-80 mol %), and organic capping agents (e.g., amine, thiol, carboxylic acid and polymer) were synthesized by colloidal chemistry methods. Transmission electron microscopy (TEM) measurements show that, depending on the particle size, the as-prepared bimetallic nanocrystals have quasi-spherical or faceted shapes. Energy-dispersive X-ray (EDX) analyses indicate that for all samples the signals of both Pt and Sn can be detected from single nanoparticles, confirming that the products are actually bimetallic but not only a physical mixture of pure Pt and Sn metal nanoparticles. X-ray diffraction (XRD) measurements were also conducted on the bimetallic particle systems. When compared with the diffraction patterns of monometallic Pt nanoparticles, the bimetallic samples show distinct shifts of the Bragg reflections to lower degrees, which gives clear proof of the alloying of Pt with Sn. However, a quantitative analysis of the lattice parameter shifts indicates that only part of the Sn atoms are incorporated into the alloy nanocrystals. This is consistent with X-ray photoelectron spectroscopy (XPS) measurements that reveal the segregation of Sn at the surfaces of the nanocrystals. Moreover, short PtSn bimetallic nanowires were synthesized by a seed-mediated growth method with amine-capped bimetallic particles as precursors. The resulting nanowires have an average width of 2.3 nm and lengths ranging from 5 to 20 nm.

Silver residues as a possible key to a remarkable oxidative catalytic activity of nanoporous gold.

Recently, several forms of unsupported gold were shown to display a remarkable activity to catalyze oxidation reactions. Experimental evidence points to the crucial role of residual silver present in very small concentrations in these novel catalysts. We focus on the catalytic properties of nanoporous gold (np-Au) foams probed via CO and oxygen adsorption/co-adsorption. Experimental results are analyzed using theoretical models represented by the flat Au(111) and the kinked Au(321) slabs with Ag impurities. We show that Ag atoms incorporated into gold surfaces can facilitate the adsorption and dissociation of molecular oxygen on them. CO adsorbed on top of 6-fold coordinated Au atoms can in turn be stabilized by co-adsorbed atomic oxygen by up to 0.2 eV with respect to the clean unsubstituted gold surface. Our experiments suggest a linking of that most strongly bound CO adsorption state to the catalytic activity of np-Au. Thus, our results shed light on the role of silver admixtures in the striking catalytic activity of unsupported gold nanostructures.

UHV studies of methanol decomposition on mono- and bimetallic CoPd nanoparticles supported on thin alumina films.

Bimetallic nanoparticles often turn out to be superior to the corresponding monometallic systems with respect to their catalytic properties. To study such effects for the methanol decomposition reaction, model catalysts were prepared by physical vapor deposition of Pd and Co under ultrahigh-vacuum (UHV) conditions. Monometallic Pd and Co particles as well as CoPd core-shell particles were generated on an epitaxial alumina film grown on NiAl(110). The interaction with methanol is examined by temperature-programmed desorption of methanol and carbon monoxide and by X-ray photoelectron spectroscopy. The decomposition of methanol proceeds in two reaction pathways independent of the particle composition: complete dehydrogenation towards carbon monoxide and hydrogen, and C--O bond scission yielding carbon deposits. Pd is the most active material studied here. The relative importance of the two channels varies for the different particle systems: on Pd dehydrogenation is preferred, whereas the C--O bond cleavage is more pronounced on Co. The bimetallic clusters show a moderate performance for both pathways. Carbon deposition poisons the model catalysts by blocking the adsorption sites for methoxide, which is the first intermediate product during methanol decomposition. In particular on Co, large amounts of carbon deposits can also be caused by dissociation of the final product of the dehydrogenation pathway, carbon monoxide. A comparison with the results of methanol decomposition on Co, Pd, and CoPd catalysts in continuous-flow reactors demonstrates that the findings of the present UHV study are relevant for catalytic performance under high-pressure conditions.

Crossover between monopole and multipole plasmon of Cs monolayers on Si(111) individually resolved in energy and momentum.

The evolution of the plasmon spectrum of the Si(111) (7 x 7)-Cs surface has been studied by energy loss spectroscopy individually resolved in energy and momentum during the transition from substrate to Cs overlayer metallization. The multipole plasmon is identified by an extremely narrow angular distribution of the inelastic electron scattering, unaccounted for by standard dipole scattering theory. A crossover between multipole and monopole surface plasmon is observed at finite surface wave vectors , depending on Cs coverage, and reveals a high sensitivity of the short-wavelength multipole components on surface morphology.