RESUMO
Owing to the high potential application need in the aerospace and structural industry for honeycomb sandwich composite, the study on the flexural behaviour of sandwich composite structure has attracted attention in recent decades. The excellent bending behaviour of sandwich composite structures is based on their facesheet (FS) and core materials. This research studied the effect of woven glass-fibre prepreg orientation on the honeycomb sandwich panel. A three-point bending flexural test was done as per ASTM C393 standard by applying a 5 kN load on different orientation angles of woven glass-fibre prepreg honeycomb sandwich panel: α = 0°, 45° and 90°. The results show that most of the sandwich panel has almost the same failure mode during the three-point bending test. Additionally, the α = 0° orientation angle shows a higher maximum load prior to the first failure occurrence compared to others due to higher flexibility but lower stiffness. In addition, the woven glass-fibre prepreg orientation angle, α = 0°, has the maximum stress and flexural modulus, which directly depend upon the maximum load value obtained during the flexural test. In addition, the experimental results and analytical prediction for honeycomb sandwich deflection show good agreement. According to the result obtained, it is revealed that woven glass-fibre honeycomb sandwich panels with an α = 0° orientation is a good alternative compared to 45° and 90°, especially when better bending application is the main purpose. The final result of this research can be applied to enhance the properties of glass-fibre-reinforced polymer composite (GFRPC) cross-arm and enhance the existing cross-arm used in high transmission towers.
RESUMO
The current work discusses ground coffee waste (GCW) reinforced high-density polyethylene (HDPE) composite. GCW underwent two types of treatment (oil extraction, and oil extraction followed by mercerization). The composites were prepared using stacking HDPE film and GCW, followed by hot compression molding with different GCW particle loadings (5%, 10%, 15% and 20%). Particle loadings of 5% and 10% of the treated GCW composites exhibited the optimum level for this particular type of composite, whereby their mechanical and thermal properties were improved compared to untreated GCW composite (UGC). SEM fracture analysis showed better adhesion between HDPE and treated GCW. The FTIR conducted proved the removal of unwanted impurities and reduction in water absorption after the treatment. Specific tensile modulus improved for OGC at 5 vol% particle loading. The highest impact energy absorbed was obtained by OGC with a 16% increment. This lightweight and environmentally friendly composite has potential in high-end packaging, internal automotive parts, lightweight furniture, and other composite engineering applications.
RESUMO
There has been much effort to provide eco-friendly and biodegradable materials for the next generation of composite products owing to global environmental concerns and increased awareness of renewable green resources. This review article uniquely highlights the use of green composites from natural fiber, particularly with regard to the development and characterization of chitosan, natural-fiber-reinforced chitosan biopolymer, chitosan blends, and chitosan nanocomposites. Natural fiber composites have a number of advantages such as durability, low cost, low weight, high specific strength, non-abrasiveness, equitably good mechanical properties, environmental friendliness, and biodegradability. Findings revealed that chitosan is a natural fiber that falls to the animal fiber category. As it has a biomaterial form, chitosan can be presented as hydrogels, sponges, film, and porous membrane. There are different processing methods in the preparation of chitosan composites such as solution and solvent casting, dipping and spray coating, freeze casting and drying, layer-by-layer preparation, and extrusion. It was also reported that the developed chitosan-based composites possess high thermal stability, as well as good chemical and physical properties. In these regards, chitosan-based "green" composites have wide applicability and potential in the industry of biomedicine, cosmetology, papermaking, wastewater treatment, agriculture, and pharmaceuticals.
RESUMO
Nowadays, pultruded glass fiber-reinforced polymer composite (PGFRPC) structures have been used widely for cross-arms in high transmission towers. These composite structures have replaced cross-arms of conventional materials like wood due to several factors, such as better strength, superior resistance to environmental degradation, reduced weight, and comparatively cheaper maintenance. However, lately, several performance failures have been found on existing cross-arm members, caused by moisture, temperature changes in the atmosphere, and other environmental factors, which may lead to a complete failure or reduced service life. As a potential solution for this problem, enhancing PGFRPC with honeycomb-filled composite structures will become a possible alternative that can sustain a longer service life compared to that of existing cross-arms. This is due to the new composite structures' superior performance under mechanical duress in providing better stiffness, excellence in flexural characteristics, good energy absorption, and increased load-carrying capacity. Although there has been a lack of previous research done on the enhancement of existing composite cross-arms in applications for high transmission towers, several studies on the enhancement of hollow beams and tubes have been done. This paper provides a state-of-the-art review study on the mechanical efficiency of both PGFRPC structures and honeycomb-filled composite sandwich structures in experimental and analytical terms.
